ACTi Q960 for RAS Configuration Guide

ACTi
Brand
ACTi
Model
Q960 for RAS
Type
Configuration Guide
Q960 Configuration Guide
with RAS
2019/05/28
www.acti.com
CONFIGURATION GUIDE
2
Part one: Access the Camera
1. Open the IP utility tool on the desktop.
2. Find the camera (Q960) you would like to install.
Note: MAC Address will be used in the second part of 1-2,
please record it for easy operation.
3. Open IE browser. (Please be sure to use IE browser.)
4. Enter the Camera IP on your browser, press “Enter” to go to the
Camera login page.
5. Fill in the account / password and click login to log in.
(Default account/ password→ User name: admin, Password: Aa123456)
www.acti.com
CONFIGURATION GUIDE
3
Part two: Settings of Camera
Please refer to the following figure for the People counting setting:
1. Click “Configuration”.
2. Click “People Counting”.
3. Click “Rule”.
4. Make sure “Enable People Counting” has been checked.
5. Adjust “Auto” to “Manual”.
6. Enter the ceiling height (from the floor) and click “Calibration”.
7. Adjust the detection area and the detection line as the picture below.
*Note: The detection lines should be drawn on the same level (There
should be no unevenness on the detection line)
www.acti.com
CONFIGURATION GUIDE
4
8. Click “Save” for the settings.
Click to draw an orange detection line.
Click to change the direction
of entry and exit.
Click to draw a polygon
detection line.
www.acti.com
CONFIGURATION GUIDE
5
A. Please refer to the following steps for data upload settings.
1. Click “Data Uploading”, check “ON” for Real-Time Upload Data
2. IP should be set the same as the MGB Server.
3. Please set URL as “/PeopleCountingApi/Q960Receiver”
4. Set the Port ” 9005”
5. Click “Save” to save the settings
6. Click “Advanced”
7. Click “Enter/Leave” for Flow Overlay
www.acti.com
CONFIGURATION GUIDE
6
8. Click “Save”.
B. Please refer below to modify the camera IP address
1. Click “Configuration”
2. Click “Network”
3. Click “Basic Settings”
4. Click “TCP/IP”
5. Uncheck “DHCP” to undo dynamic IP address setting
6. This is the IP address to configure
7. Subnet mask
8. Router address
9. Click “Save” to save the settings
www.acti.com
CONFIGURATION GUIDE
7
10. When the settings are done, restart to apply all the settings. Click OK
to restart.
www.acti.com
CONFIGURATION GUIDE
8
Part three: Set up related parameters for the webpage
1. Open the webpage (Using Google chrome browser)
http://localhost/MAS_RetailPackage/Setting/mgbmanagement.aspx
2. Sign in RAS (admin/123456)
3. Add new device settings
3-1. Click “Overview” “Setting” “MGB Server”
3-2. Click the same name as the one attached to the server. (Ex: MGB
Server)
3-3. Click “Add new device” as the picture below
www.acti.com
CONFIGURATION GUIDE
9
3-4 Choose “Q960A” for the Device Type (Please refer to the picture
below)
www.acti.com
CONFIGURATION GUIDE
10
3-5 Configure the details of the device
Camera name:
(Store name +960+location)
MAC Address:
Fill in the default Camera
MAC, please refer to step 2
of the first part.
Note: The minus sign (-) of
the MAC address must be
replaced with a colon (:)
Stream URL: Please
keep it blank.
Camera IP:Enter the IP of
Q960.
HTTP PORT Maintain the
number “80”
Account:admin
Password:Aa123456
3-6 Click “ Save”
3-7 Be sure all the devices
have been set properly,
then click “Lock”.
Click “Lock”→ Press “Save”
（If there are still other devices that need to be added (except Q960),
please click “Lock” after all the devices have been set without error.）
Note: The saved settings cannot be changed after clicking “Lock”！
（If there’s any setting error and need to adjust, please contact ACTi
customer service to unlock.）
www.acti.com
CONFIGURATION GUIDE
11
4. Store Settings
Click” Setting”→” Store”
1. Click “Add Store”
2. Click “Enabled”
3. Name: Store name
4. Address: Enter the address and set the location (click sign)
5. Bussiness Hour: Confirm with the customer and set the store opening hours
6. Enter Third Account None.
7. Select “Foot Traffic Device” same as the device we mentioned above.
8. Click “Save”
9. Click “Lock”, then press “Save” again for the settings
（Please wait for the store to complete the related information, click “Lock” after
confirmed.）
Note: The saved settings cannot be changed after clicking “Lock”！
（If there’s any setting error and need to adjust, please contact ACTi
customer service to unlock.）
www.acti.com
CONFIGURATION GUIDE
12
5. Permission
1. Click “Setting”
2. Click “UserManagement”
3. Click “Add a User”
4. Account Name：Fill in the login account
5. Email：Fill in the Email
6. Password：Fill in the Password
7. Role：Select “Manager”
8. Store：Click the store you set on step 4
9. Click “Save” to save the settings
Copyright © 2019, ACTi Corporation All Rights Reserved
7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan
114, R.O.C.
TEL : +886-2-2656-2588 FAX : +886-2-2656-2599
Email: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

ACTi Q960 for RAS Configuration Guide

ACTi
Brand
ACTi
Model
Q960 for RAS
Type
Configuration Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents