Barco DLite 14 Owner's manual

Brand: Barco

Model: DLite 14

Type: Owner's manual

Barco DLite 14 is a high-quality display solution designed for a wide range of applications, including corporate presentations, educational settings, and home entertainment. With its sleek design and advanced features, the Barco DLite 14 offers an immersive and engaging visual experience.

The DLite 14 boasts a brilliant 14-inch TFT LCD panel with a resolution of 1366 x 768, delivering sharp and vivid images. Its high contrast ratio and wide viewing angles ensure excellent visibility from any vantage point. The display also supports a variety of input sources, including HDMI, VGA, and composite video, making it easy to connect to laptops, PCs, and other devices.

Barco service bulletin

Serial Number: 782

Date: 20/10/2008

Product: DLite tiles

Priority code*: A

”Must” modiﬁcation, Barco will provide the necessary components to perform this modiﬁcation

at no charge.

Improves the reliability of the product.

Improves the general working conditions of t he pr odu ct.

For information only.

1. DLITE PLASTIC HANDLES MAY B REAK OFF

DUE TO Y EARS OF EXPOS URE TO VARYING

CLIMATE CONDITIONS

1.1 General

Phenom enon

The plastic handles of some DLite tiles may break during handling.

Cause

After years of exposure to varying climate conditions the plastic materi

al of the handles of

all types of DLite tiles becomes fragile.

Solution

Replacement of both plastic handles of the DLite tiles with two new metal handles. Barco

offers a spare part kit which contains 50 metal DLite handles and 100 suitable replacement

screws to upgrade 25 DLite tiles. The order number of the spare part kit with metal DLite

handles is R860883K. This Info-T contains the proper instructions for replacement of the

plastic DLite handles.

Since the handles are also the attachment points for the safety cable of the DLite tile it is

mandatory that the handles are replaced as soon as possible for all type of DL ite tiles in

either rental or ﬁxed installations.

Scope

All type of DL ite tiles with plastic handles (e.g. left side of image 1-1). This Info-T is not

applicable upon DLite tiles with moulded handles (e.g. right side o f image 1-1).

Image 1-1

Barco nv Media & Entertain ment Division

Noordlaan 5, B-8520 Kuurne

www.barco.com

Page 1 of 4

Barco service bulletin

1.2 Replacement of the DLite handles

This procedure describes how to replace the handles of a DLite tile while

the t ile is mounted in the DLite display (on site). The same procedure

is applicable upon unmounted DLite tiles (e.g. at a workshop). The in-

structions regarding the safety cable can be omitted when replacing the

handles of unmounted DLite tiles (e.g. at a workshop).

WARNING: Replace one handle at a time so that the DLite tile is always se-

cured with a safety cable through the remaining handle. The replacement

should be done as soon as possible to avoid potential hazard to persons

and or property.

Necessary tools

4 mm Allen wrench (included in the kit).

Necessary parts

• Two metal handles per DLite tile.

• Two M5x10 hexagon socket head cap screws per handle.

How to replace the handles of the DLite tile?

1. Make sure that the DLite tile is secured with a safety cable. The safety cable (reference

1 of image 1-2) must pass through the upper handle (reference 2 of image 1-2) to form

a closed loop with the support structure of the DLite display.

Image 1-2

2. Remove the lower plastic handle (reference 3 of

image 1-3) by unscrewing the two cur-

rent hexagon socket head cap screws (reference 4 of image 1-3). Use the included 4 mm

Allen wrench.

Image 1-3

3. Install the lower metal handle (reference 5 of image 1-4) as illustrated. Tighten the

handle with two M5x10 replacement hexagon socket head cap screws (reference 6 of

image 1-4) until it is ﬁrmly secured. Use the included 4 mm Allen wrench.

IMPORTANT NOTICE: Do not reuse the longer screws from the plastic handle to

secure the metal handle. The metal handles are less thick and thus the screws

are shorter.

InfoT: 782

Page 2 of 4

Barco service bulletin

Image 1-4

4. Reinstall the safety cable (reference 7 of image 1-5) so that it passes through the newly

mounted lower metal handle to form a closed loop with the support structure of the DLite

display.

Image 1-5

5. Remove the upper plastic handle (reference 8 of image 1-6) by unscrewing the two cur-

rent hexagon socket head cap screws (reference 9 of image 1-6). Use the included 4 mm

Allen wrench.

Image 1-6

6. Install the upper metal handle (reference 10 of image 1-7) as illustrated. Tighten the

handle with two M5x10 replacement hexagon socket head cap screws (reference 11 of

image 1-7) until it is ﬁrmly secured. Use the included 4 mm Allen wrench.

IMPORTANT NOTICE: Do not reuse the longer screws from the plastic handles to

secure the metal handles. The metal handles are less thick and thus the screws

are shorter.

Image 1-7

Page 3 of 4 InfoT: 782

Barco service bulletin

1.3 Approvals

Modiﬁcation approved by:

Quality Director MED

Danny Van Hoof

R&D Manager

Bruno D evos

Product M anager

Thomas Van Damme

If you should have any more questions, or remarks, please do not hesitate to contact our

technical support team on following E-mail address “service.mne@barco.com”.

InfoT: 782

Page 4 of 4

Barco DLite 14 Owner's manual

Barco DLite 14 Owner's manual

Barco DLite 14 Owner's manual

Related papers

Other documents