LG ABNC488RLA0.ENCTEVH Owner's manual

Brand: LG

Model: ABNC488RLA0.ENCTEVH

Type: Owner's manual

P/No.:MFL68047203

TYPE : CEILING CONCEALED DUCT

MFL68047203

Introduction

Installation of Indoor,

Outdoor Unit

Connecting Pipes to the

Indoor Unit

Connecting Cables

between Indoor Unit and

Outdoor Unit

Air Purging and

Evacuation

External Static Pressure &

air Flow

Checking the Power Cord &

Test Running

Installation Guide at the

Seaside

2 Safety Precautions

Important Safety Instructions

Connecting Pipes to the

Outdoor Unit

Checking the Drainage

Group Control

2 Ceiling Concealed Duct Type Air Conditioner

TABLE OF CONTENTS

TIPS FOR SAVING ENERGY

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

• Do not cool excessively indoors. This may be harmful for your health and may consume

more electricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air con-

ditioner is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may

block the air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them on a label on the side of each unit.

Dealer’s name :

Date of purchase :

Safety Precautions

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak

performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

•

The product shall be installed according to the wiring regulations of the corresponding country.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment mal-

function, property damage, personal injury and/or death.

Installation

• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, control box

cover are removed or opened.

- it may cause fire, electric shock, explosion or death.

• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.

- There is risk of fire or electric shock.

• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.

- Do not disassemble or repair the product. There is risk of fire or electric shock.

• Always ground the product.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Do not modify or extend the power cable.

- There is risk of fire or electric shock.

• Be cautious when unpacking and installing the product.

- Sharp edges could cause injury. Be especially careful of the case edges and the fins on the con-

denser and evaporator.

• For installation, always contact the dealer or an Authorized Service Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the air conditioner could fall with it, causing property damage, product failure,

and personal injury.

4 Ceiling Concealed Duct Type Air Conditioner

• Do not let the air conditioner run for a long time when the humidity is very high and a door or a win-

dow is left open.

- Moisture may condense and wet or damage furniture.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress

air or Oxygen and Do not use Flammable gases. Otherwise, it may cause fire or explosion.

- There is the risk of death, injury, fire or explosion.

Operation

• Do not store or use flammable gas or combustibles near the product.

- There is risk of fire or failure of product.

CAUTION

Installation

• Always check for gas (refrigerant) leakage after installation or repair of product.

- Low refrigerant levels may cause failure of product.

• Install the drain hose to ensure that water is drained away properly.

- A bad connection may cause water leakage.

• Keep level even when installing the product.

- To avoid vibration or water leakage.

• Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods.

- It may cause a problem for your neighbors.

• Use two or more people to lift and transport the product.

- Avoid personal injury.

• Do not install the product where it will be exposed to sea wind (salt spray) directly.

- It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could

cause product malfunction or inefficient operation.

Installation Manual 5

Installation Parts Provided

Air outlet vents

Air intake vents

Remote Controller

(Side)

(Rear)

Air intake vents

Air outlet vents

Piping

Drain hose

Connecting wire

Control cover

(Side)

(Rear)

Air outlet

vents

Air intake

vents

Connecting Wire

Drain Hose

Connection Pipe

Control Cover

TEMP

FAN

SPEED

OPER

MODE

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that could cause harm to the

air conditioner.

This symbol indicates special notes.

NOTICE

launaM siht ni desU slobmyS

Features

Introduction

6 Ceiling Concealed Duct Type Air Conditioner

Installation Manual 7

Installation of Indoor, Outdoor Unit

Indoor unit

Install the air conditioner in the location that

satises the following conditions.

t The place shall easily bear a load exceeding

four times the indoor unit ’s weight.

t The place shall be able to inspect the unit as

the gure.

t The place where the unit shall be leveled.

t The place shall allow easy water

drainage.(Suitable dimension “H” is necessary

to get a slope to drain as gure.)

t The place shall easily connect with the

outdoor unit.

t The place where the unit is not aected by an

electrical noise.

t The place where air circulation in the room will

be good .

t There should not be any heat source or steam

near the unit

Outdoor unit

t If an awning is built over the unit to prevent

direct sunlight or rain exposure, be careful that

heat radiation from the condenser is not

restricted.

t There should not be any animals or plants

which could be aected by hot air discharged.

t Ensure the spaces indicated by arrows from

the wall, ceiling, f

ence or other obstacles.

t Take the weight of the air conditioner into

account and select a place where noise and

vibration are minimum.

t Select a place where the warm air and noise

from the air conditioner do not disturb

neighbors.

600600

Top view

(unit: mm)

Front view

Front

Inspection hole

(600X600)

Control box

1000

More than

30 cm

More than

30 cm

More than

70 cm

Sunroof

Fence or

obstacles

Selection of the best location

Installation of Indoor, Outdoor Unit

Piping length and the elevation

Outdoor unit

Indoor unit

Outdoor unit

Indoor unit

Oil trap

Outdoor unit

Indoor unit

Elevation B

(m)

Gas Liquid

Standard

Max. Max.

AB-C186HLA0 12.7 (1/2″) 6.35 (1/4″) 7.5 15 7 20

AB-C246HLA0 15.88 (5/8″) 9.52 (3/8″) 7.5 30 20 20

AB-C308GLA0 15.88 (5/8″) 9.52 (3/8″) 7.5 50 30 20

AB-C368GLA0 15.88 (5/8″) 9.52 (3/8″) 7.5 50 30 25

AB-C428GLA0 15.88 (5/8″) 9.52 (3/8″) 7.5 50 30 25

AB-C488RLA0 15.88 (5/8″) 9.52 (3/8″) 7.5 50 30 30

AB-C548RLA0 19.05 (3/4″) 9.52 (3/8″) 7.5 50 30 30

Model

Pipe Size

(Diameter : Φ)

Length A

(m)

Additional

refrigerant

(g/m)

CAUTION:

is on the basis of reliability.

If AB-C548RLA0 Model is installed at a distance of 30 m, 675 g of refrigerant

should be added (30 m-7.5 m) x 30 g/m = 675 g.

8 Ceiling Concealed Duct Type Air Conditioner

Installation Manual 9

Installation of Indoor, Outdoor Unit

Installation of Unit

Install the unit above the ceiling correctly.

to absorb unnecessary vibration.

as a figure for easy water drainage.

can support the weight of the unit.

vibration.

performed.

CASE 1

POSITION OF SUSPENSION BOLT

Drainage hole

1-3 mm

(G)

M10 Nut

M10 SP. washer

M10 washer

X 4

(Local

supply)

X 4

M10 Nut

M10 SP. washer

M10 washer

X 4

(Local

supply)

X 4

CASE 2

POSITION OF CONSOLE BOLT

(Unit:mm)

1282 1230 477 56 590 30 120 1006 294

1232 1182 355 45.5 450 30 87 830 186

Dimension

Model

A B C D E F (G) H I

932 882 355 45.5 450 30 87 750 163

AB-C186HLA0

AB-C246HLA0

AB-C308GLA0

AB-C368GLA0

AB -C428GLA0

AB -C488RLA0

AB -C548RLA0

Indoor unit installation

Installation of Indoor, Outdoor Unit

• Select and mark the position for fixing bolts.

• Drill the hole for set anchor on the face of

ceiling.

• Insert the set anchor and washer onto the

suspension bolts for locking the suspension

bolts on the ceiling.

• Mount the suspension bolts to the set anchor

firmly.

• Secure the installation plates onto the

suspension bolts (adjust level roughly) using

nuts, washers and spring washers.

CAUTION:

Tighten the nut and bolt to

prevent unit falling.

1 Set anchor

Old building New building

2 Plate washer

3 Spring washer

4 Nut

5 Suspension

bolts

10 Ceiling Concealed Duct Type Air Conditioner

Installation of Indoor, Outdoor Unit

Ceiling

1~3 mm

Drainage hole

U-Trap

70 mm

2 x SP

SP = External Pressure

(mmAq)

Ex) External Pressure

= 10 mmAq

70 mm

40 mm

20 mm

Make sure to be closed.

Unit

Drainage pipe

(Local supply)

Thermal insulator

(Local supply)

Drainage hole

CAUTION FOR GRADIENT OF

UNIT AND DRAIN PIPING

Lay the drain hose with a downward

inclination so water will drain out.

Front of view

inclination (1/50 to 1/100).

Prevent any upward flow or reverse flow in

any part.

shall always be provided for the drain pipe.

a water leakage caused by the blocking

of intake air filter.

Applied U-Trap Dimension

1. Install declination of the indoor unit is very important for the drain of the duct type air

conditioner.

2. Minimum thickness of the insulation for the connecting pipe shall be 5mm.

installation.

CORRECT

INCORRECT

allowed

CAUTION

Installation Manual 11

Installation of Indoor, Outdoor Unit

Drill the piping hole with 70 mm dia, hole core

drill.

Piping hole should be slightly slant to the

outdoor side.

5~7 mm

Indoor Outdoor

WALL

INSULATION, OTHERS

Insulate the joint and tubes completely.

All thermal insulation must comply with local requirement.

INDOOR UNIT

REFRIGERANT PIPE

Insulate and tape the gas piping.

CAUTION: Cutting line of

insulation must look upper

direction. Thickness of

insulation is 7 mm or over.

Recommended Insulation

material

Material: FOAM PE

Thickness : 10 mm

Density : less than 0.032±0.005(g/cm

)

Thermal conductivity : less than

0.03(kcal/m.hr. °C)

NOTICE

Air distribution Is the air circulation good?

Drain Is the drainage smoothly and no sweating?

Gas leakage Is the piping connection correctly?

Wiring Is the wiring connection correctly?

Lock-bolt Is the lock-bolt of compressor loosened?

THERMAL INSULATION

TEST AND CHECK

Make sure that there is no clearance here.

Overlap with thermal

insulator for piping.

Thermal insulator for refrigerant pipe

(Local supply)

Thermal insulator for

piping(Local supply)

Hose clip for thermal insulator(Local supply)

Union for liquid pipe

Refrigerant pipe and thermal

insulator(Local supply)

Union for gas pipe

Thermal insulator for refrigerant pipe

(Local supply)

Hose clip for thermal insulator

(Local supply)

Make sure insulate and tape gas and liquid side piping entirely.

Power cable

Thermal insulator

Gas pipe

Liquid pipe

Tape

Filter Drier installation on the connecting pipe is not recommended.It can lead to capacity decreasing.

FILTER DRIER

12 Ceiling Concealed Duct Type Air Conditioner

1. Please fix tightly using provided screw after placing remote controller setup board

on the place where you like to setup.

- Please set it up not to bend because poor setup could take place if setup board bends.

Please set up remote controller board fit to the reclamation box if there is a reclamation box.

2. Can set up Wired remote controller cable into three directions.

- Setup direction: the surface of wall reclamation, upper, right

- If setting up remote controller cable into upper and right side, please set up after removing remote controller

cable guide groove.

❈

Remove guide groove with long nose.

①

Reclamation to the surface of the wall

②

Upper part guide groove

③

Right part guide groove

Installation instruction

Installation Manual 13

Installation of Indoor, Outdoor Unit

Wall

Side

Wall

Side

Wall

Side

Wall

Side

3. Please fix remote controller upper part into the

backplate attached to the surface of the wall, as

the picture below, and then, connect with

backplate by pressing lower part.

- Please make sure to leave no gaps on the top, bottom, left or right

sides between the remote controller and backplate.

- Before assembly with the backplate, arrange the Cable not to

interfere with circuit parts.

Remove remote controller by inserting a

screwdriver into the lower separating holes and

twisting to release the controller from backplate.

- There are two separating holes. Please individually separate one

at a time.

- Please be careful not to damage the inside

components when separating.

4. Please refer to the following directions when connecting the indoor unit and the

wired remote controller together.

1) Please connect the cables as shown in the figure below when connecting the plug type cable from the

indoor unit’s C/BOX and the housing type of the extension cable.

2) When connecting Terminal Blocks of the indoor C/BOX and the wired remote controller with the extension

cable, refer to the steps below.

①

Remove the screw on the cable which is fastened to the wired remote controller’s Terminal Block by

loosening with a screw driver.

②

Remove the housing of the provided 32ft extension cable with a cutting nipper and peel it as shown in the

figure below. (when purchasing the extension cable at the site directly, please peel it as shown in the figure

below.)

Please check if the connectors are connected properly.

C/BOX Cable (Plug type)

Extension cable(housing type)

Indoor

Unit side

TEMP

FAN

SPEED

OPER

MODE

• Specification of LG supplied extension cable: AWG#22, 3 core shielded. (Model : PZCWRC1)

Apply enclosed noncombustible conduit(metal raceway) totally or use FT-6 rated cable or above level in

case of local electric & building code that requires plenum (CMP) cable usage.

CAUTION

Signal Yellow

12V Red

GND Black

1.378 inch(35 mm)

±0.197 inch(5 mm)

0.394 inch(10 mm) ± 0.118 inch(3 mm)

14 Ceiling Concealed Duct Type Air Conditioner

Installation of Indoor, Outdoor Unit

ENGLISH

5. Please use an extension cable if the distance between the wired remote controller

and the indoor unit is longer than 32ft(10 m).

③

Make sure each wire is securely fastened under each screw terminal and the wires are not in contact with

each other.

④

Please connect the Terminal blocks of indoor unit’s C/BOX and wired remote controller by referring to the

images and contents shown below.

Connect the yellow(signal) part of the wired remote controller’s terminal block and the ‘YL’ part of the indoor

unit’s terminal block.

Connect the red(12V) part of the wired remote controller’s terminal block and the ‘RD’ part of the indoor

unit’s terminal block.

Connect the black(GND) part of the wired remote controller’s terminal block and the ‘BK’ part of the indoor

unit’s terminal block.

In case of loosened screws or insufficient contact between the terminal and the wire, remote controller

may not function properly.

When the power is off on the remote controller, check the connection between the remote controller and

Terminal Block.

Use an appropriate screwdriver for tightening the terminal screws. A screwdriver with a small head will

strip the head and make proper tightening impossible.

Over-tightening the terminal screws may break wires and terminal block structure.

• Installation work must be performed in accordance with the national wiring standards and local by

authorized personnel only.

• Installations must comply with the applicable local/national or international standards.

• AWG#22, 3 core shielded is recommended when using the large hole in the center of the back plate.

• AWG#24, 3 core shielded is recommended when using the side or top knock-out of the back plate.

CAUTION

When installing the wired remote controller, do not bury it in the wall.

(It can cause damage in the temperature sensor.)

Do not install the cable to be 164ft(50 m) or longer. (It can cause communication error.)

CAUTION

Remote controller

PCB Terminal

block Remark

Indoor

Terminal

block

Function

YELLOW YL Signal

RED RD 12V

BLACK BK GND

YELLOW RED BLACK

Signal 12V GND

Remote

controller PCB

Indoor unit

side

Installation Manual 15

Installation of Indoor, Outdoor Unit

Remote controller installation

Since the room temperature sensor is in the remote controller, the remote controller box

should be installed in a place away from direct sunlight, high humidity and direct supply of

cold air to maintain proper space temperature. Install the remote controller about 5ft(1.5m)

above the floor in an area with good air circulation at an average temperature.

Do not install the remote controller where it can be affected by:

- Drafts, or dead spots behind doors and in corners.

- Hot or cold air from ducts.

- Radiant heat from sun or appliances.

- Concealed pipes and chimneys.

- Uncontrolled areas such as an outside wall behind the remote controller.

- This remote controller is equipped with LCD display. For proper display of the remote

controller LCD's, the remote controller should be installed properly as shown in Fig.1.

(The standard height is 4~5 ft (1.2~1.5 m) from floor level.)

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

5feet

(1.5meters)

(Fig. 1)

Direct

Sun ray contact area

yes

Installation of Indoor, Outdoor Unit

16 Ceiling Concealed Duct Type Air Conditioner

Installation Manual 17

Installation of Indoor, Outdoor Unit

Connecting Pipes to the Indoor Unit

Main cause of gas leakage is defect in flaring

work. Carry out correct flaring work in the

following procedure.

Cut the pipes and the cable.

purchased locally.

the outdoor unit.

distance.

length.

Burrs removal

section of pipe/tube.

downward direction as you remove burrs in

order to avoid to let burrs drop in the tubing.

Putting nut on

outdoor units, than put them on pipe/tube

having completed burr removal.

(Not possible to put them on after flaring work)

Flaring work

shown below.

Firmly hold copper tube in a bar(or die) as

indicated dimension in the table above.

Check

flared section and do flaring work again.

Outside Diameter "A"

6.35(1/4") 1.1~1.3

9.52(3/8") 1.5~1.7

12.70(1/2") 1.6~1.8

15.88(5/8") 1.6~1.8

19.05(3/4") 1.9~2.1

Copper

tube

Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper flaring =

Preparation of Piping

18 Ceiling Concealed Duct Type Air Conditioner

Installation of Indoor, Outdoor Unit

Pipe bending

Annealed copper pipe with small diameter ( ø6.35 or ø9.52) can be easily bent manually. In this

case, secure large R(radius) for the bend section and gradually bend pipe. If annealed copper pipe

is large in diameter ( ø15.88 or ø19.05), bend pipe with bender. Use bender appropriate for the pipe

diameter.

Brazing

In refrigerant piping, bending (in particular, acute bending) must be minimized to reduce piping

resistance. Bending is, however, necessary in some places by virtue of the installation position of

devices auxiliary to the packaged air conditioner, or of the building structure, piping distance or

finishing appearance. If a more acute bend is required than that attainable by pipe bender, perform

brazing using ready-made elbow. Aside from this function, brazing also serves to connect straight

pipes, generally using ready-made sockets. While brazing, protect piping against heat with wet cloth

to avoid damaging valve packing or burning thermal insulator with burner heat. While brazing, blow

iner

t gas (nitrogen gas or carbonic gas) to prevent formation of oxidation film in copper piping;

otherwise, the refrigerant circuit will clog. The blowing of nitrogen gas (or carbonic gas) through 3-

way valves is described in the following:

Refrigerant piping(Flare piping)

When connecting piping, be sure to keep piping dry(keep piping away from water), clean (keep

piping away from dust) and airtight (avoid refrigerant leakage).

When connecting piping on rainy days or making a through-hole in wall, take due care to prevent

water or plaster from entering piping.

Water enters Plaster enters

CAUTION:

• This procedure is designed to prevent formation of oxidation film by

filling piping with inert gas. Note that excessive gas pressure will

generate pinholes at brazed points.

(Nitrogen gas: Supply pressure 0.05~0.1 kg/cm

• When supplying inert gas, be sure to open one end of piping.

Connecting Pipes to the Indoor Unit

Installation Manual 19

Connecting Pipes to the Outdoor Unit

Checking the Drainage

Connecting the pipes to the Outdoor

unit

tighten the flare nut with fingers.

until the wrench clicks.

- When tightening the flare nut with torque

wrench, ensure the direction for tightening

follows the arrow on the wrench.

Checking the Drainage

- Spray one or two glasses of water upon the

evaporator.

- Ensure that water flows drain hose of indoor

unit without any leakage.

Liquid side piping

(Smaller Dia.)

Gas side piping

(Bigger Dia.)

Torque wrench

Outdoor unit

Pipe size kgf

m N

6.35(1/4") 1.8~2.5 14~18

9.52(3/8") 3.4~4.2 36~42

12.70(1/2") 5.5~6.6 49~61

15.88(5/8") 6.3~8.2 68~82

19.05(3/4") 9.9~12.1 100~120

Connecting Pipes to the Indoor Unit

20 Ceiling Concealed Duct Type Air Conditioner

Page is loading ...

LG ABNC488RLA0.ENCTEVH Owner's manual

LG ABNC488RLA0.ENCTEVH Owner's manual

LG ABNC488RLA0.ENCTEVH Owner's manual

Related papers

Other documents