Fujitsu RDG12LLTA Installation guide

Brand: Fujitsu

Model: RDG12LLTA

Category: Split-system air conditioners

Type: Installation guide

INSTALLATION MANUAL

For authorized service personnel only.

INSTALLATIONSANLEITUNG

Nur für autorisiertes Personal.

MANUEL D'INSTALLATION

Pour le personnel agréé uniquement.

MANUAL DE INSTALACIÓN

Solo para personal autorizado.

MANUALE D'INSTALLAZIONE

Ad uso esclusivo del personale autorizzato.

ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ

Για εξουσιοδοτημένο προσωπικό σέρβις.

MANUAL DE INSTALAÇÃO

Apenas para técnicos autorizados.

РУКОВОДСТВО ПО УСТАНОВКЕ

Для уполномоченного персонала.

KURULUM KILAVUZU

Yetkili servis personeli içindir.

INSTALLATION MANUAL

AIR CONDITIONER

INDOOR UNIT

Duct Type

hcstueDsiaçnarFloñapsEonailatIάkIvηλλEsêugutroP

hsilgnE

eçkrüT

йикссуР

PART NO. 9374815173-04

9374815173-04_IM.indb 1 9/21/2011 1:45:04 PM

En-1

CAUTION!

This mark indicates procedures which, if improperly performed,

might possibly result in personal harm to the user, or damage to

property.

Read carefully all security information before use or install the air conditioner.

Do not attempt to install the air conditioner or a part of the air conditioner by yourself.

This unit must be installed by qualified personnel with a capacity certificate for handling

refrigerant fluids. Refer to regulation and laws in use on installation place.

e installation must be carried out in compliance with regulations in force

in the place

of installation and the installation instructions of the manufacturer.

This unit is part of a set constituting an air conditioner. It must not be installed alone or

with non-authorized by the manufacturer.

Always use a separate power supply line protected by a circuit breaker operating on all

wires with a distance between contact of 3mm for this unit.

The unit must be correctly grounded and the supply line must be equipped with a

differential breaker in order to protect the persons.

The units are not explosion proof and therefore should not be installed in explosive

atmosphere.

Never touch electrical components immediately after the power supply has been turned

off. Electric shock may occur. After turning off the power, always wait 5 minutes before

touching electrical components.

This unit contains no user-serviceable parts. Always consult authorized service

personnel to repairs.

When moving, consult authorized service personnel for disconnection and installation of

the unit.

2. ABOUT THE UNIT

2.1. Precautions for using the R410A refrigerant

WARNING

• Do notintroduceanysubstance other than the prescribed refrigerant into the

refrigeration cycle.

If air enters the refrigeration cycle, the pressure in the refrigeration cycle will become

abnormally high and cause the piping to rupture.

• Ifthereisarefrigerantleakage,makesurethatitdoesnotexceedtheconcentration

limit.

If a refrigerant leakage exceeds the concentration limit, it can lead to accidents such

as oxygen starvation.

• Do nottouch refrigerant thathas leaked fromthe refrigerant pipe connections or

other area. Touching the refrigerant directly can cause frostbite.

• If a refrigerant leakage occurs during operation, immediately vacate the premises

and thoroughly ventilate the area.

 Iftherefrigerantcomesincontactwithaame,itproducesatoxicgas.

2.2. Special tool for R410A

WARNING

• To install a unit that uses the R410Arefrigerant, use dedicated toolsand piping

materialsthathavebeenmanufacturedspecicallyforR410Ause.

 BecausethepressureoftheR410Arefrigerantisapproximately1.6timeshigherthan

the R22, failure to use dedicated piping material or improper installation can cause

rupture or injury.

Furthermore, it can cause serious accidents such as water leakage, electric shock, or

re.

Tool name Contents of change

Gauge manifold

•Pressureishugeandcannotbemeasuredwithaconventional

gauge. To prevent erroneous mixing of other refrigerants, the

diameter of each port has been changed.

It is recommended to use a gauge manifold with a high

pressuredisplayrange–0.1to5.3MPaandalowpressure

displayrange–0.1to3.8MPa.

Charging hose

•Toincreasepressureresistance,thehosematerialandbase

size were changed.

Vacuum pump

• Aconventionalvacuumpumpcanbeusedbyinstallinga

vacuum pump adapter.

Gas leakage

detector

•SpecialgasleakagedetectorforHFCrefrigerantR410A.

1. SAFETY PRECAUTIONS

• BesuretoreadthisManualthoroughlybeforeinstallation.

• ThewarningsandprecautionsindicatedinthisManualcontainimportantinformation

pertaining to your safety. Be sure to observe them.

• HandthisManual,togetherwiththeOperatingManualtothecustomer.

Request the customer to keep them on hand for future use, such as for relocating or

repairing the unit.

WARNING!

This mark indicates procedures which, if improperly performed,

might lead to the death or serious injury of the user.

• Requestyourdealeroraprofessionalinstallertoinstalltheunitinaccordancewith

thisManual.

An improperly installed unit can cause serious accidents such as water leakage,

electricshock,orre.

 IftheunitisinstalledindisregardoftheinstructionsintheInstallationManual,itwill

void the manufacturer’s warranty.

• DonotturnONthepoweruntilallworkhasbeencompleted.

 Turning ON the power before thework is completed can cause serious accidents

suchaselectricshockorre.

• Ifrefrigerantleakswhileworkisbeingcarriedout,ventilatethearea.

Iftherefrigerantcomesincontactwithaame,itproducesatoxicgas.

• Installationworkmustbeperformedinaccordancewithnationalwiringstandardsby

authorized personnel only.

• ExceptforEMERGENCY, neverturn offmainas wellassub breakerof theindoor

units during operation. It will cause compressor failure as well as water leakage.

First, stop the indoor unit by operating the control unit, converter or external input

device and then cut the breaker.

 Makesuretooperatethroughthecontrolunit,converterorexternalinputdevice.

When the breaker is designed, locate it at a place where the users cannot start and

stop in the daily work.

INSTALLATION MANUAL

PARTNO.9374815173-04

INDOORUNIT(DuctType)

Contents

1. SAFETYPRECAUTIONS ..........................................................................................1

2. ABOUTTHEUNIT

2.1.PrecautionsforusingtheR410Arefrigerant .......................................................1

2.2.SpecialtoolforR410A ........................................................................................1

2.3. Accessories ........................................................................................................2

2.4.Optionalparts .....................................................................................................2

3. INSTALLATIONWORK

3.1.Selectinganinstallationlocation ........................................................................2

3.2A.Installationdimensions(Ceilingconcealedtype) .............................................3

3.2B.

Installationdimensions(Wallmountedtype/Floorstandingconcealedtype) ...3

3.3A.Installationtheunit(Ceilingconcealedtype) ....................................................3

3.3B.Installtheunit(Wallmountedtype/Floorstandingconcealedtype) ................5

PIPEINSTALLATION

4.1.Selectingthepipematerial .................................................................................6

4.2.Piperequirement ................................................................................................7

4.3.Flareconnection(Pipeconnection) ....................................................................7

4.4.Installingheatinsulation .....................................................................................7

5. INSTALLINGDRAINPIPES

5.1A.Installingdrainpipes(Ceilingconcealedtype) .................................................8

5.1B.Installingdrainpipes(Wallmountedtype/Floorstandingconcealedtype) .............8

5.2. Install the drain pipe ...........................................................................................8

6. ELECTRICALWIRING

6.1.Wiringsystemdiagram .....................................................................................11

6.2.Connectioncablepreparation ........................................................................... 11

6.3.Connectionofwiring .........................................................................................11

7. REMOTECONTROLLERSETTING

7.1.Installingtheremotecontroller .........................................................................12

7.2.Settingthedipswitches ....................................................................................12

7.3.Functionsetting ................................................................................................13

7.4.Jumperwiresetting ..........................................................................................14

7.5.Specialinstallationmethods .............................................................................15

8. TESTRUN ...............................................................................................................15

9. OPTIONALPARTS

9.1.Wiredremotecontroller(Simpleremotecontroller) ..........................................16

9.2.Externalinputandexternaloutput ....................................................................16

9.3.Remotesensor(Optionalparts) .......................................................................16

9.4.IRReceiverUnit(Optionalparts) ......................................................................16

9.5.Autolouvergrille(Optionalparts) .....................................................................17

9.6.Optionalpartscablebinding .............................................................................17

10. CUSTOMERGUIDANCE ........................................................................................17

11. ERRORCODES ......................................................................................................18

9374815173-04_IM.indb 1 9/21/2011 1:45:04 PM

En-2

2.3. Accessories

WARNING

• Forinstallationpurposes,besure tousethepartssupplied bythemanufactureror

other prescribed parts.

The use of non-prescribed parts can cause serious accidents such as the unit to fall,

waterleakage,electricshock,orre.

• Thefollowinginstallationpartsarefurnished.Usethemasrequired.

• KeeptheInstallationManualinasafeplaceanddonotdiscardanyotheraccessories

until the installation work has been completed.

Do not discard any accessories needed for installation until the installation work has

been completed.

Name and Shape Q’ty Application

OperatingManual

InstallationManual

(Thisbook)

Installation

template

For positioning the indoor

unit

Washer

For installing indoor unit

Coupler

heat insulation

(Large)

For indoor side pipe joint

(Largepipe)

Coupler

heat insulation

(Small)

For indoor side pipe joint

(Smallpipe)

Binder

Medium

For power supply and

transmission and remote

controller cable binding.

Large

For fixing the coupler heat

insulation.

Filter(Small)

(7000,9000,12000,14000BTU/h)

Filter(Big)

(18000BTU/h)

Drain hose

For installing drain pipe

VP25(O.D.32,I.D.25)

Name and Shape Q’ty Application

Hoseband

For installing drain hose

Drain hose insulation B

Insulates the drain hose

Wired Remote

Controller

RemoteController

Cable

For connecting the

remote controller

Tapping screw

(M4×16mm)

For installing the remote

controller

2.4. Optional parts

Parts name Model No. Application

Wired remote controller UTY-RNN*M For air conditioner operation

SimpleRemoteController UTY-RSN*M For air conditioner operation

IRReceiverUnit UTY-LRH*M For the wireless remote controller

Remote sensor unit UTY-XSZX Room temperature sensor

External control set UTD-ECS5A Forcontrolinput/outputport

Auto louver grille UTD-G*S*-W Air outlet grille with auto louver

3. INSTALLATION WORK

3.1. Selecting an installation location

Especially, the installation place is very important for the split type air conditioner

becauseitisverydifculttomovefromplacetoplaceaftertherstinstallation.

WARNING

• Selectinstallationlocationsthatcanproperlysupporttheweightoftheindoor.Install

the units securely so that they do not topple or fall.

CAUTION

• Donotinstalltheunitinthefollowingareas:

• Areawithhighsaltcontent,suchasattheseaside.

It will deteriorate metal parts, causing the parts to fail or the unit to leak water.

• Arealledwithmineraloilorcontainingalargeamountofsplashedoilorsteam,

such as a kitchen.

It will deteriorate plastic parts, causing the parts to fail or the unit to leak water.

• Area that generates substances that adversely affect the equipment, such as

sulfuric gas, chlorine gas, acid, or alkali.

It will cause the copper pipes and brazed joints to corrode, which can cause

refrigerant leakage.

• Areathatcancausecombustiblegastoleak,containssuspendedcarbonbersor

ammabledust,orvolatileinammablessuchaspaintthinnerorgasoline.

 Ifgasleaksandsettlesaroundtheunit,itcancauseare.

• Areawhereanimalsmayurinateontheunitorammoniamaybegenerated.

• Do not use the unit for special purposes, such as storing food, raising animals,

growing plants, or preserving precision devices or art objects.

It can degrade the quality of the preserved or stored objects.

• Donotinstallwherethereisthedangerofcombustiblegasleakage.

• Donotinstalltheunitnearasourceofheat,steam,orammablegas.

• Installtheunitwheredrainagedoesnotcauseanytrouble.

• Install the indoor unit, outdoor unit, power supply cable, transmission cable, and

remotecontroller cableat least 1m awayfrom atelevisionor radioreceivers.The

purpose of this is to prevent TV reception interference or radio noise.

(Evenifthey areinstalledmore than1mapart,you couldstillreceive noiseunder

somesignalconditions.)

9374815173-04_IM.indb 2 9/21/2011 1:45:06 PM

En-3

CAUTION

• Ifchildrenunder10yearsoldmayapproachtheunit,takepreventivemeasuresso

that they cannot reach the unit.

• Decide the mounting position with the customer as follows:

(1) Installtheindoorunitinalocationhavingsufcientstrengthtosupporttheweightof

the indoor unit.

(2) Theinletandoutletportsshouldnotbeobstructed;theairshouldbeabletoblowall

over the room.

(3) Leavethespacerequiredtoservicetheairconditioner.

(4) Locatewheretheaircanbedistributedevenlythroughouttheroombytheunit.

(5) Installtheunitwhereconnectiontotheoutdoorunitiseasy.

(6) Installtheunitwheretheconnectionpipecanbeeasilyinstalled.

(7) Installtheunitwherethedrainpipecanbeeasilyinstalled.

(8) Installtheunitwherenoiseandvibrationisnotamplied.

(9) Takeservicing,etc.,intoconsiderationandleavethespaces.Alsoinstalltheunit

wheretheltercanberemoved.

3.2A. Installation dimensions (Ceiling concealed type)

ProvideaServiceaccessforinspectionpurposes.

Do not place any wiring or illumination in the service space, as they will impede service.

Installation Dimensions

Left

side

Stronganddurableceiling

Indoor unit

Right

side

150mm

or more

400mm

or more

Serviceaccess Ceiling

2500mmormore

(Whennoceiling)

Floor

240mmormore

20mmormore

300mmormore

Adjust the wind direction in the room depending on the shape of blow out opening.

Serviceaccess

Unit

Control

box

400mm

or more

100mm

or more

300mm

or more

Servicespace

3.2B.

Installation dimensions (Wall mounted type/Floor

standing concealed type)

Thewallmountedtype/oorstandingconcealedtyperequiresatemperature

correctionsetting.Performthisin“7.3.Functionsetting”.

Strongand

durableoor

10mm

or less

Leftside

150mm

or more

150mm

or more

150mm

or more

150mm

or more

150mm

or more

150mm

or more

20mm

or more

20mm

or more

20mm

or more

20mm

or more

400mm

or more

400mm

or more

Inlet air

Strongand

durableoor

Strongand

durableoor

10mm

or less

Right side

(PIPEside)

Right side

(PIPEside)

Grille

Duct

Grille

Strongand

durableoor

3.3A. Installation the unit (Ceiling concealed type)

WARNING

• Install the air conditioner in a location which can withstanda load do at least 5

times the weight of the main unit and which will not amplify sound or vibration. If the

installation location is not strong enough, the indoor unit may fall and cause injuries.

• If the job is done with thepanel frame only,there is a risk that theunit will come

loose.Pleasetakecare.

3.3A.1. UNIT INSTALLATION EXAMPLE (CEILING CONCEALED

TYPE)

Connectthelocallypurchasedduct.

(1)Inletside

• Connecttheducttothelocallypurchasedinletange.

• Connecttheangetothebodywiththelocallypurchasedtappingscrews.

• Windtheinletangeconnectingtotheductwiththealuminumtapeetc.toavoidthe

air discharge.

CAUTION

• Whentheductisconnectedtoinletside,removecontainedlterandsurelyattach

locallypurchasedlteratinletopening.

(2)Outletside

• Connecttheductwithadjustinginsideofoutletange.

• Windtheoutletangeconnectingtotheductwiththealuminumtapeetc.toavoidthe

air discharge.

• Insulatetheducttoavoidthedewcondensation.

CAUTION

• Check that duct work doesnot exceed the rangeof externalstaticpressure of

equipment.

• Makesuretoinsulateductstoavoidthedewcondensation.

• Makesuretoinsulatebetweenductsandwallsifmetalductsareused.

• Pleaseexplainhandlingandwashingmethodsoflocallypurchasedmaterialstothe

customer.

• Topreventpeoplefromtouchingthepartsinsidetheunit,besuretoinstallgrilleson

the inlet and outlet ports. The grilles must be designed in such a way that cannot be

removed without tools.

• Whenconnectingtheducttotheoutletportoftheindoorunit,besuretoinsulatethe

outlet port and the installation screws to prevent water from leaking around the port.

AR07/09/12/14/18Model

• Setthestatic pressure outside the unit to 90 Pa or less (the allowable range is

between0and90Pa).

9374815173-04_IM.indb 3 9/21/2011 1:45:07 PM

En-4

Replace the cover as follows.

• Removethescrews,andthenremovecoverandfanguard.

• Installthecoverwiththescrewsasshownintheillustrationbelow.

Model

Screw

7000,9000,12000,14000BTU/h 9

18000BTU/h 11

screw(M5)

Cover

Fan guard

SideInlet-SideOutlet

Insulationmaterial(Fieldsupply)

Aluminum tape

Flange(Fieldsupply)

Air

Duct

(Fieldsupply)

Air

Intake grille

(Fieldsupply)

SideInlet-SideOutlet(Duct)

Insulationmaterial(Fieldsupply)

Aluminum tape

Tapping screw for

angeconnection

(M5x10mm/

Fieldsupply)

Flange(Fieldsupply)

Air

Duct

(Fieldsupply)

Air

Intake grille

(Fieldsupply)

BottomInlet-SideOutlet

Duct(Fieldsupply)

Intakegrille(Fieldsupply)

Air

Outletside

Inlet side

7000,9000,12000,14000BTU/h 18000BTU/h

A 650mm 850mm

B P200×2=400mm P200×3=600mm

CAUTION

• Be sure to install the air inlet grille and the air outlet grille for aircirculation. The

correct temperature cannot be detected.

• Grills mustbexed so that man cannot touch indoor unit fan and exchanger, and

cannot be removed by only hand operation without tool.

• Besuretoinstalltheairlterintheairinlet.

If the air fi lter is not installed, the heat exchanger may be clogged and its

performance may decrease.

3.3A.2. INSTALL THE FILTERS

• Installthelterstotheunit.

Filter(Accessories)

Unit

Filter

3.3A.3.

DRILLING HOLES FOR BOLTS AND INSTALLING THE BOLTS

• Usingtheinstallationtemplate,drillholesforbolts(4holes).

Drilling position

for bolts

Installation template

Air

377mm

7000,9000,12000,14000BTU/h 18000BTU/h

A 734mm 934mm

9374815173-04_IM.indb 4 9/21/2011 1:45:12 PM

En-5

3.3B. Install the unit (Wall mounted type/ Floor standing

concealed type)

WARNING

• Install the air conditioner in a location which can withstand a load doat least 5

times the weight of the main unit and which will not amplify sound or vibration. If the

installation location is not strong enough, the indoor unit may fall and cause injuries.

• If the job is done with the panel frame only, there is a risk that the unitwill come

loose.Pleasetakecare.

3.3B.1. UNIT INSTALLATION EXAMPLE

(Wall mounted type/Floor standing concealed type)

Connectthelocallypurchasedduct.

(1)Inletside

• Connecttheducttothelocallypurchasedinletange.

• Connecttheangetothebodywiththelocallypurchasedtappingscrews.

• Windtheinletangeconnectingtotheductwiththealuminumtapeetc.toavoidthe

air leakage.

CAUTION

• Whentheductisconnectedtoinletside,removecontainedlterandsurelyattach

locallypurchasedlteratinletopening.

(2)Outletside

• Connecttheductwithadjustinginsideofoutletange.

• Windtheoutletangeconnectingtotheductwiththealuminumtapeetc.toavoidthe

air discharge.

• Insulatetheducttoavoidthedewcondensation.

CAUTION

• Check that duct work doesnot exceed the rangeof externalstaticpressure of

equipment.

• Makesuretoinsulateductstoavoidthedewcondensation.

• Makesuretoinsulatebetweenductsandwallsifmetalductsareused.

• Pleaseexplainhandlingandwashingmethodsoflocallypurchasedmaterialstothe

customer.

• Topreventpeoplefromtouchingthepartsinsidetheunit,besuretoinstallgrilleson

the inlet and outlet ports. The grilles must be designed in such a way that cannot be

removed without tools.

• Whenconnectingtheducttotheoutletportoftheindoorunit,besuretoinsulatethe

outlet port and the installation screws to prevent water from leaking around the port.

• Set the static pressure outside the unit to 90Pa or less (the allowable range is

between0and90Pa).

• Removethescrews,andthenremovecoverandfanguard.

• Installthecoverwiththescrewsasshownintheillustrationbelow.

Model

Screw

7000,9000,12000,14000BTU/h 9

18000BTU/h 11

Cover

Fan guard

screw(M5)

3.3A.4. FIX THE UNIT

(1)Hangtheunit

Hangerbolt

Nut A

(Fieldsupply)

Nut B

(Fieldsupply)

Washer

(Accessories)

Hanger

Hangerbolt

Nut A

(Fieldsupply)

Washer

(Accessories)

Nut B

(Fieldsupply)

Unit

Hanger

20mm

length

Cover

*:It might become difficult to open and shut the Cover /control box cover when the

lengthexceeds20mm.

(2)Leveling

Base horizontal direction leveling on top of the unit.

Ceiling

Level

NOGOOD

10mmorless

Level

Air

OK NOGOOD

10mmorless

CAUTION

• Leaveaspaceof100mmormorebetweentheinletportandtheceiling.

• FastentheunitsecurelywithSpecialnutsAandB.

9374815173-04_IM.indb 5 9/21/2011 1:45:17 PM

En-6

3.3B.2. INSTALL THE FILTER

• Installthelters(Accessories)totheunit.

Filter

Unit

Filter

Replace drain cap

CAUTION

• Set“7.4.JumperwiresettingofDrainagefunctionsetting(JM1)”.

• Drain pump cannot be used if it is installed in wallmounted type/floor standing

concealed type.

3.3B.3. INSTALLING THE UNIT

(1)Fixingmethodoftheunit

• Topreventoverturning,xtheunittotheoororthewall.

• Toavoidthevibrationoftheunit,insertthespacerbetweentheunitandtheoororthe

wall,andxit.

(2)Leveling

Base horizontal direction leveling on top of the unit.

Level

10mmorless

NOGOOD

Level

NOGOODOK

10mmorless

CAUTION

•

 FastentheunitsecurelywithSpecialnutsAandB.

PIPE INSTALLATION

CAUTION

• Be careful that foreign matter (oil, water, etc.) does not enter the piping with

refrigerantR410Amodels.Also,whenstoringthepiping,securelysealtheopenings

by pinching, taping, etc.

• While brazing the pipes, be sure to purge with dry nitrogen gas.

4.1. Selecting the pipe material

CAUTION

• Do not use existing pipes.

• Use pipes that have clean external and internal sides without any contamination

which may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or

water.

• It is necessary to use seamless copper pipes.

Material:Phosphordeoxidizedseamlesscopperpipes

Itisdesirablethattheamountofresidualoilislessthan40mg/10m.

• Do not use copper pipes that have a collapsed, deformed, or discolored portion

(especiallyontheinteriorsurface).Otherwise,theexpansionvalveorcapillarytube

may become blocked with contaminants.

• Improperpipeselectionwilldegradeperformance.AsanairconditionerusingR410A

incurs pressure higher than when using conventional refrigerant, it is necessary to

choose adequate materials.

•

ThicknessesofcopperpipesusedwithR410Aareasshowninthetable.

•

Never use copper pipes thinner than those indicated in the table even if they are

available on the market.

Thicknesses of Annealed Copper Pipes (R410A)

Pipe outside diameter [mm (in.)] Thickness [mm]

6.35(1/4) 0.80

9.52(3/8) 0.80

12.70(1/2) 0.80

15.88(5/8) 1.00

19.05(3/4) 1.20

9374815173-04_IM.indb 6 9/21/2011 1:45:20 PM

En-7

4.2. Pipe requirement

CAUTION

• Referto the Installation Manualof the outdoor unitfor description of thelength of

connecting pipe or for difference of its elevation.

• Usepipewithwater-resistantheatinsulation.

CAUTION

• Install heat insulation around both the gas and liquid pipes. Failure to do so may

cause water leaks.

Useheatinsulationwithheatresistanceabove120°C.(Reversecyclemodelonly)

In addition, if the humidity level at the installation location of the refrigerant piping is

expectedtoexceed70%,installheatinsulationaroundtherefrigerantpiping.Ifthe

expectedhumiditylevelis70-80%,useheatinsulationthatis15mmorthickerand

iftheexpectedhumidityexceeds80%,useheatinsulationthatis20mmorthicker.

Ifheatinsulationisusedthatisnotasthickasspecied,condensationmayformon

the surface of the insulation. In addition, use heat insulation with heat conductivity of

0.045W/(m·K)orless(at20°C).

4.3. Flare connection (Pipe connection)

WARNING

• Tightenthe are nuts with a torque wrench using the specied tighteningmethod.

Otherwise,thearenutscouldbreakafteraprolongedperiod,causingrefrigerantto

leakandgenerateahazardousgasiftherefrigerantcomesintocontactwithaame.

4.3.1. Flaring

• UsespecialpipecutterandaretoolexclusiveforR410A.

(1)

Cuttheconnectionpipetothenecessarylengthwithapipecutter.

(2)

Hold the pipe downward so that cuttings will not enter thepipe and remove any

burrs.

(3)

Insertthearenut(alwaysusethearenutattachedtotheindoorandoutdoorunits

respectively)ontothepipeandperformtheareprocessingwithaaretool.Use

thespecialR410Aaretool,orthe conventionalaretool. Leakageofrefrigerant

mayresultifotherarenutsareused.

(4)

Protectthepipesbypinchingthemorwithtapetopreventdust,dirt,orwaterfrom

entering the pipes.

Die

Pipe

Checkif[L]isareduniformly

and is not cracked or scratched.

Pipe outside diameter

[mm (in.)]

Dimension A [mm]

Dimension B

0.4

[mm]

Flare tool for R410A,

clutch type

6.35(1/4)

0to0.5

9.1

9.52(3/8) 13.2

12.70(1/2) 16.6

15.88(5/8) 19.7

19.05(3/4) 24.0

Whenusing conventional are tools to are R410Apipes, the dimensionAshould be

approximately0.5mmmorethanindicatedinthetable(foraringwithR410Aaretools)

toachievethespeciedaring.UseathicknessgaugetomeasurethedimensionA.

Width across

ats

Pipe outside

diameter [mm (in.)]

Width across flats

of Flare nut [mm]

6.35(1/4) 17

9.52(3/8) 22

12.70(1/2) 26

15.88(5/8) 29

19.05(3/4) 36

4.3.2. Bending pipes

•

If pipes are shaped by hand, be careful not to collapse them.

•

Donotbendthepipesinananglemorethan90°.

•

When pipes are repeatedly bend or stretched, the material will harden, making it

difculttobendorstretchthemanymore.

•

Do not bend or stretch the pipes more than 3 times.

CAUTION

• To prevent breaking of the pipe, avoid sharp bends.

• If the pipe is bent repeatedly at the same place, it will break.

4.3.3. Pipe connection

CAUTION

• Be sure to install the pipe against the port on the indoor unit correctly. If the centering

isimproper,thearenutcannottightensmoothly.Ifthearenutisforcedtoturn,the

threads will be damaged.

• Do not removethe flare nut fromthe indoor unit pipe until immediatelybefore

connecting the connection pipe.

• Holdthetorquewrenchatitsgrip,keepingitatarightanglewiththepipe,inorderto

tightenthearenutcorrectly.

• Tightentheare nutswith a torquewrench using thespecied tightening method.

Otherwise,thearenutscouldbreakafteraprolongedperiod,causingrefrigerantto

leakandgenerateahazardousgasiftherefrigerantcomesintocontactwithaame.

• Connectthepipingsothatthecontrolboxcovercaneasilyberemovedforservicing

when necessary.

• Inordertopreventwaterfromleakingintothecontrolbox,makesurethatthepiping

is well insulated.

Whenthearenutistightenedproperlybyyourhand,holdthebodysidecouplingwith

aseparatespanner,thentightenwithatorquewrench.(Seethetablebelowfortheare

nuttighteningtorques.)

Tighten with 2 wrenches.

Holdingwrench

Flare nut

Connectionpipe

Torque wrench

Indoor unit pipe

(Bodyside)

Flare nut [mm (in.)] Tightening torque [N·m (kgf·cm)]

6.35(1/4)dia. 16to18(160to180)

9.52(3/8)dia. 32to42(320to420)

12.70(1/2)dia. 49to61(490to610)

15.88(5/8)dia. 63to75(630to750)

19.05(3/4)dia. 90to110(900to1,100)

4.4. Installing heat insulation

Install the heat insulation material after performing a refrigerant leak check (see the

InstallationManualfortheoutdoorunitfordetails).

4.4.1. COUPLER HEAT INSULATION

• Insulatewiththecouplerheatinsulation(Accessories)aroundthegaspipeandliquid

pipe at indoor unit.

• Afterinstallingthecouplerheatinsulation,wrapbothendswithvinyltapesothat

there is no gap.

• Afterafxingthecouplerheatinsulation,secureitwith2binders(large),oneoneach

end of the insulation.

• Makesurethatthebindersoverlaptheheatinsulationpipe.

Couplerheat

insulation

(Accessories)

Coverthisportionwith

heat insulation.

Binder(Large)

(Accessories)

Heatinsulation

CAUTION

• Afterchecking for gas leaks (refer to the Installation Manual of the outdoor unit),

perform this section.

• Installheatinsulationaroundboththelarge(gas)andsmall(liquid)pipes.Failureto

do so may cause water leaks.

9374815173-04_IM.indb 7 9/21/2011 1:45:21 PM

En-8

5. INSTALLING DRAIN PIPES

5.1A. Installing drain pipes (Ceiling concealed type)

Usegeneralhardpolyvinylchloridepipeandconnectitwithadhesive(polyvinylchloride)

so that there is no leakage.

Always heat insulate the indoor side of the drain hose.

Useadrainpipethatmatchesthesizeofthedrainhose(TableA).

• Donotperformarise,trapandairbleeding.

• Provideadownwardgradient(1/100ormore).

• Providesupportswhenlongpipesareinstalled.

• Useaninsulationmaterialasneeded,topreventthepipesfromfreezing.

• Installthepipesinawaythatallowsfortheremovalofthecontrolbox.

Table A

O.D.

Drain pipe 32mm(VP25)

CEILINGCONCEALEDTYPE(UseDrainPump)

Outletair

ow

Arrange the drain hose

lower than this port.

Drain hose

Trap

NOGOODDrain cap NOGOOD

Rise

Air bleeding

Supporter

NOGOOD

1.5to2m

• Installthedrainpipewithdownwardgradient(1/50to1/100)andsotherearenorises

or traps in the pipe.

• Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm] and

connectitwithadhesive(polyvinylchloride)sothatthereisnoleakage.

• Whenthepipeislong.Installsupports.

• Donotperformairbleeding.

• Alwaysheatinsulatetheindoorsideofthedrainpipe.

VP25

[O.D32mm

ormore]

Horizontalor

upward gradient

Supporter

Gapof1.5-2m

Locallyarrangedpipe

Max.

300mm

700mmorless

RiseAir bleeding

BAD

Trap

Observe the following procedures to construct centralized drain pipe ttings

VP30ormore[O.D38mmormore]

Downwardgradient1/100ormore

700mmorless

WARNING

• Do not insert the drain piping into the sewer where sulfurous gas occurs. (Heat

exchangeerosionmayoccur)

• Insulatethepartsproperlysothatwaterwillnotdripfromtheconnectionparts.

• Check for proper drainage afterthe construction by using the visible portion of

transparentdrainportandthedrainpipingnaloutletonthebody.

CAUTION

• Donotapplyadhesiveagentonthedrainportofthebody.

 (Usetheattacheddrainhoseandconnectthedrainpiping)

5.1B. Installing drain pipes (Wall mounted type/Floor

standing concealed type)

NOGOOD

RiseTrap

Drain

cap

CAUTION

• Drain pump cannot be usedif it is installed in wall mounted type/floor standing

concealed type.

• Set“7.4.JumperwiresettingofDrainagefunctionsetting(JM1)”.

• Besuretoconnectthepipesfordrainagewithoutleakage.

• Toavoidcondensationanddripping,alwaysinsulatetheindoordrainpipe.

5.2. Install the drain pipe

(1)BesuretousesuppliedDrainhose

andHoseband

Hoseband

Drain

hole

Drain hose

HardPVCside

• When drain pump is used.(Ceilingconcealedtypeonly)

Hoseband

4mmorless

20mm

• When drain pump is not used.(Naturaldrainage)

Jointpipe

(Fieldsupply)

Drainpipe(VP25)

(Fieldsupply)

Applying

area of

adhesive

4mmorless

CAUTION

• Whendrainpumpisnotused,donotconnecttheaccessorydrainhoseandsoftPVC

hose directly

9374815173-04_IM.indb 8 9/21/2011 1:45:22 PM

En-9

(2)

Be sure to insert Drain hose

to the very end of the Drain pan of the unit with no space

Applying

area of

adhesive

Jointpipe

(Fieldsupply)

Drainpipe(VP25)

(Fieldsupply)

4mmorless

Hoseband

Drain hose

FastentheHoseband

at the position where

vertical against ground.

TheHoseband

must be positioned at the right

side of the Drain hose

asinthegure.

CAUTION

• DonotconnecttotheDrainholewithadhesive.Usingadhesivemaycausedamage

and water leaks.

(3) AfterinstallingtheDrainhose

, check if the drainage is smooth.

• When drain pump is not used.(Naturaldrainage)

Downward

gradient

2.5-5.0mm

CAUTION

• TopreventexcessiveforceonDrainhose

,avoidbendsortwists.(Tobendortwist

maycausewaterleaks.)

(4) Aftercheckingfordrainage,attachtheDrainhoseinsulationB

to insulate, following

theinstructionsasinthegures.

To avoid space with Drain hose

andHoseband

,pressrmlytheDrainhose

insulation B

• When drain pump is used.(Ceilingconcealedtypeonly)

Drain hose

insulation B

Ensure there is

no space.

• When drain pump is not used.(Naturaldrainage)

Drain hose

insulation B

Ensure there is

no space.

• STEP1~STEP3

Butt the insulation against the unit.

STEP1

Unit

Slit

Pressrmly

STEP2

Slit

Pressrmly

Roll the

insulation

over the joint.

STEP3

Pressrmly

Slit

• FINISH

Checkthatthereisnogapbetweentheunitandthedrainhoseinsulation.

• When drain pump is used.(Ceilingconcealedtypeonly)

Do not cover the

panel window.

• When drain pump is not used.(Naturaldrainage)

Do not cover the

control box cover.

Note: Check for drainage

Pourabout1literofwaterfromthepositionshowninthediagramorfromtheairow

outlettothecondensatetray.Checkforanyabnormalitiessuchasstrangenoisesand

whether the drain pump functions normally.

CAUTION

•Makesurethedrainwaterisproperlydrained.

9374815173-04_IM.indb 9 9/21/2011 1:45:23 PM

En-10

6. ELECTRICAL WIRING

Cable Cable size (mm

) Type Remarks

Connectioncable 1.5 Type60245IEC57 3Cable+Ground,1φ230V

Max.CableLength:Limitvoltagedroptolessthan2%.Increasecablegaugeifvoltagedropis

2%ormore.

WARNING

• Electrical work mustbe performed in accordance with this Manual by a person

certiedunderthenationalorregionalregulations.Besuretouseadedicatedcircuit

for the unit.

 Aninsufcientpowersupplycircuitorimproperlyperformedelectricalworkcancause

seriousaccidentssuchaselectricshockorre.

• Beforestartingwork, checkthat powerisnot beingsupplied totheindoor unitand

outdoor unit.

• Forwiring, use the prescribed typeof cables, connect them securely,making sure

that there are no external forces of the cables applied to the terminal connections.

Improperly connected or secured cables can cause serious accidents such as

overheatingtheterminals,electricshock,orre.

• Securelyinstalltheelectricalboxcoverontheunit.

An improperly installed electrical box cover can cause serious accidents such as

electricshockorrethroughexposuretodustorwater.

• Installsleevesintoanyholesmadeinthewallsforwiring.Otherwise,ashortcircuit

could result.

• Use the included connection cables and power cables or ones specified by the

manufacturer. Improper connections, insufficient insulation, or exceeding the

allowablecurrentcancauseelectricshockorre.

• Donotmodifythepowercables,useextensioncables,oruseanybranchesinthe

wiring. Improper connections, insufficient insulation, or exceeding the allowable

currentcancauseelectricshockorre.

• Match the terminal blocknumbers and connection cable colors with those of the

outdoor unit or branch box. Erroneous wiring may cause burning of the electric parts.

• Securelyconnecttheconnectioncablestotheterminalboard.Inaddition,securethe

cables with wiring holders. Improper connections, either in the wiring or at the ends

ofthewiring,cancauseamalfunction,electricshock,orre.

• Alwaysfastentheoutsidecoveringoftheconnectioncablewiththecableclamp.(If

theinsulatorischafed,electricleakagemayoccur.)

• Installaearthleakagebreaker.Inaddition,installtheearthleakagebreakersothat

theentireACmainpowersupplyiscutoffatthesametime.Otherwise,electricshock

orrecouldresult.

• Always connect the earth cable.

Improper grounding work can cause electric shocks.

• Install the remote controller cables so as not to be direct touched with your hand.

• Performwiringworkinaccordancewithstandardssothattheairconditionercanbe

operated safely and positively.

• Connecttheconnectioncablermlytotheterminalboard.Imperfectinstallationmay

causeare.

CAUTION

• Groundtheunit.

Do not connect the earth cable to a gas pipe, water pipe, lightning rod, or a telephone

earth cable.

Improper grounding may cause electric shock.

• Do not connect powersupply cables to the transmissionor remotecontroller

terminals, as this will damage the product.

• Neverbundlethepowersupplycableandtransmissioncable,remotecontrollercable

together.

 Separatethesecableby50mmormore.

Bundling these cables together will cause miss operation or breakdown.

• WhenhandlingPCB,staticelectricitychargedinthebodymaycausemalfunctionof

thePCB.Followthecautionsbelow:

• Establishagroundfortheindoorandoutdoorunitsandperipheraldevices.

• Cutpower(breaker)off.

• Touch metal part of the indoor and outdoor units for more than 10 seconds to

discharge static electricity charged in the body.

• DonottouchterminalsofpartsandpatternsimplementedonPCB.

(1) Useringterminalswithinsulatingsleevesasshowninthegurebelowtoconnectto

the terminal block.

(2) Securelyclamptheringterminalstothecablesusinganappropriatetoolsothatthe

cables do not come loose.

(3) Usethespeciedcables,connectthemsecurely,andfastenthemsothatthereisno

stress placed on the terminals.

(4) Useanappropriatescrewdrivertotightentheterminalscrews.

Do not use a screwdriver that is too small, otherwise, the screw heads may be

damaged and prevent the screws from being properly tightened.

(5) Donottightentheterminalscrewstoomuch,otherwise,thescrewsmaybreak.

(6) Seethetablefortheterminalscrewtighteningtorques.

(7) Pleasedonotx2powersupplycableswith1screw.

Strip10mm

Sleeve

Screwwithspe-

cial washer

Screwwith

special washer

Ring terminal

Cable

Terminal block

Ring terminal

Ring

terminal

WARNING

• Useringterminalsandtightentheterminalscrewstothespeciedtorques,otherwise,

abnormal overheating may be produced and possibly cause heavy damage inside

the unit.

Tightening torque

M4screw

1.2to1.8N·m

(12to18kgf·cm)

9374815173-04_IM.indb 10 9/21/2011 1:45:23 PM

En-11

6.1. Wiring system diagram

ConnectioncabletooutdoorunitorBRANCHBOX

INDOORUNIT

OUTDOORUNITor

BRANCHBOX

TERMINAL

Type60245IEC57

Cablesize1.5mm

(Inter-unit)

Powerlines

Groundingline

Powerline

Controlline

Pleaseconnectitto

thespeciedterminal.

Wired remote controller cable

*Groundtheremotecontroller

(Pleaseconnectitwhennecessary.)

Red

White

Black

Indoor

unit side

CAUTION

Tighten the indoor unit connection cable and power supply indoor and outdoor unit,

branch box terminal board connections rmly with the terminal board screws.Faulty

connectionmaycauseare.

If the indoor unit connection cable and power supply are wired incorrectly, the air

conditioner may be damaged.

 Connect the indoor unit connection cable by matching the numbers of the outdoor,

branch box and indoor units terminal board numbers as shown in terminal label.

Earth both the indoor and outdoor, branch box units by attaching a earth cable.

 Unitshallbegroundedincompliancewiththeapplicablelocalandnationalcables.

CAUTION

 Besuretorefertotheabovediagramfordocorrecteldwiring.Wrongwiringcauses

malfunction of the unit.

 Checklocalelectricalrulesandalsoanyspecicwiringinstructionsorlimitation.

6.2. Connection cable preparation

Keep the earth wire longer than the other wires.

Powersupplycable

or connection cable

20mm

30mmormore

Earth wire

•Usea4-corewirecable.

6.3. Connection of wiring

(1) Removethecontrolboxcoverfromthecontrolbox.

Screw

Controlboxcover

Removethe4screws

and remove the control

box cover from the

control box.

(2) Cableconnection

• Connect the connection cable to the terminal board.

• Connecttheremotecontrollercabletotheterminalboard.

• Fixtheremotecontrollercabletothecontrolboxcoverwithanylonclamp.

Remote controller cable

1:Red

2:White

3:Black

Earth

Binder(Medium)

(Accessories)

Powersupplycable

Binder(Medium)

(Accessories)

Remote controller cable

Powersupplycable

9374815173-04_IM.indb 11 9/21/2011 1:45:24 PM

En-12

7. REMOTE CONTROLLER SETTING

CAUTION

When detecting the room temperature using the remote con-

troller, please set up the remote controller according to the

following conditions. If the remote controller is not located prop-

erly, the correct room temperature will not be detected, and

thusabnormalconditions like“not cooled”or“not heated”will

occur even if the air-conditioner is running normally.

• Locatewhereanaveragetemperaturefortheroombeing

air conditioned will be sensed.

• Donotlocatedirectlyexposedtotheoutletairfromthe

air-conditioner.

• Locateoutofdirectsunlight.

• Locateawayfromtheinuenceofotherheatsources.

DonottouchtheremotecontrollerPCboardandPCboardpartsdirectlywithyourhands

Do not wire the remote controller cable together with or parallel to the connection ca-

bles,andpowersupplycableofthe INDOORUNITandOUTDOORUNIT,BRANCH

BOX.Itmaycauseerroneousoperation.

When installing the bus wire near a source of electromagnetic waves, use shielded wire

DonotsettheDIPswitches,eitherontheairconditionerortheremotecontroller,inany

way other than indicated in this manual that is supplied with the air conditioner. Doing

so may result in improper operation.

7.1. Installing the remote controller

Opentheoperationpanelonthefrontoftheremotecontroller,removethe2screwsindi-

catedinthefollowinggure,andthenremovethefrontcaseoftheremotecontroller.

When installing the remote controller, remove the connector from the front case. The

wires may break if the connector is not removed and the front case hangs down.

When installing the front case, connect the connector to the front case.

Screws

SET BACK

Front case

(backside)

Rear case

Connector

When remote controller cable is concealed

(1) Concealtheremotecontrollercable.

(2) Passtheremotecontrollercablethroughtheholeintherearcaseandconnectthe

remotecontrollercabletotheremotecontrollerterminalboardspeciedingure.

(3) Clamptheremotecontrollercablesheathwiththebinderasshowningure.

(4) Cutofftheexcessbinder.

(5) Installtherearcasetothewall,box,etc.,with2screwsgure.

Binder

(Small)

1.Red

2. White

3. Black

CAUTION

When connecting the remote controller

wires, do not overtighten the screws.

Hole

[Example]

Remote

controller cable

Box

Screws

Connector

Rear case

Groundtheremotecontrollerifithasagroundwire.

Wrap the connector and remote

controller wires with vinyl tape

or some other type of insulation

asshowninthegure.

Remote controller

Temperature

sensor

120

45.3

33.5

Hole

15.3

4.5

4.5 12.5

Hole×3

Hole×2

83.5

63.5

Unit:mm

CAUTION

Install the remote controller wires so as not to be direct touched with your hand.

Donot touchthe remote controllerPC boardand PC boardparts directly withyour

hands.

7.2. Setting the dip switches

SettheremotecontrollerDIPswitches.

[Example]

OFF

DIPswitch1

Frontcase(backside)

NO.

SW state

Detail

OFF ON

DIP-

switch 1

★

Cannotbeused.

(Donotchange)

★

Dual remote controller setting

*Referto2.DUALREMOTECONTROL-

LERSin7.5.SpecialInstallationMethods.

★

Cannotbeused.

(Donotchange)

★

Cannotbeused.

(Donotchange)

★

Cannotbeused.

(Donotchange)

★

Invalidity Validity

Memorybackupsetting

*SettoON tousebatteries forthememory

backup. If batteries are not used, all of the

settings stored in memory will be deleted if

there is a power failure.

(

★

Factorysetting)

9374815173-04_IM.indb 12 9/21/2011 1:45:25 PM

En-13

7.3. Function setting

This procedure changes the function settings used to control the indoor unit according to

the installation conditions. Incorrect settings can cause the indoor unit to malfunction. This

procedure should be performed by authorized installation or service personnel only.

Performthe“FUNCTIONSETTING”accordingtotheinstallationconditionsusingtheremote

controller.(Refertotheindoorunitinstallationmanualfordetailsonthefunctionnumbers

andsettingvalues.)

(1) PresstheSETTEMP.buttons(

)( )andFANbuttonsimultaneouslyformorethan

5 seconds to enter the function setting mode.

TH FR

(2) PresstheSETBACKbuttontoselecttheindoorunitnumber.

TH FR

UnitnumberofINDOORUNIT

SETBACK

(3) PresstheSETTIME( )buttonstoselectthefunctionnumber.

Function number

TH FR

(4) PresstheSETTEMP.buttons( )( )toselectthesettingvalue.

Thedisplayashesasshowntotherightduringsettingvalueselection.

Settingvalue

TH FR

(5) PresstheTIMERSETbuttontoconrmthesetting.

PresstheTIMERSETbuttonforafewsecondsuntilthesettingvaluestopsashing.

Ifthesettingvaluedisplaychangesorif“--”isdisplayedwhentheashingstops,the

setting value has not been set correctly.

(Aninvalidsettingvaluemayhavebeenselectedfortheindoorunit.)

(6) Repeatsteps2to5toperformadditionalsettings.

PresstheSETTEMP.buttons(

)( )andFANbuttonsimultaneouslyagainfor

more than 5 seconds to cancel the function setting mode. In addition, the func-

tionsettingmodewillbeautomaticallycanceledafter1minuteifnooperationis

performed.

(7) AftercompletingtheFUNCTIONSETTING,besuretoturnoffthepowerandturniton

again.

• Function Details

(1) Filter Sign

Theindoorunithasasigntoinformtheuserthatitistimetocleanthelter.Selectthe

timesettingfortheltersigndisplayintervalinthetablebelowaccordingtotheamount

ofdustordebrisintheroom.Ifyoudonotwishtheltersigntobedisplayed,selectthe

settingvaluefor“Noindication”.

(♦...Factorysetting)

Setting description

Function

number

Setting value

Standard(400hours)

Longinterval(1000hours) 01

Shortinterval(200hours) 02

♦

No indication 03

(2) Static pressure

Selectappropriatestaticpressureaccordingtotheinstallationconditions.

(♦...Factorysetting

)

Setting description

Function

number

Setting value

0Pa

10Pa 01

20Pa 02

30Pa 03

40Pa 04

50Pa 05

60Pa 06

70Pa 07

80Pa 08

90Pa 09

♦25Pa[Standard] 31

Rangeofstaticpressureisdifferentfrom1modeltoother.

Range of static pressure 0to90Pa

(3) Cooling room temperature correction

Depending on the installed environment, the room temperature sensor may require a

correction.

The settings may be selected as shown in the table below.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

Standard

30

Slightlylowercontrol 01

Lowercontrol 02

Warmer control 03

Whenusingoorconsoleinstallation,changethesettingvalueto“01”.

(4) Heating room temperature correction

Depending on the installed environment, the room temperature sensor

may require a

correction.

The settings may be changed as shown in the table below.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

Standard

Lowercontrol 01

Slightlywarmercontrol 02

Warmer control 03

Whenusingoorconsoleinstallation,changethesettingvalueto“01”.

(5) Auto restart

Enable or disable automatic system restart after a power outage.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

Yes

No 01

9374815173-04_IM.indb 13 9/21/2011 1:45:25 PM

En-14

*Autorestartisanemergencyfunctionsuchasforpowerfailureetc.Donotstartandstop

the indoor unit by this function in normal operation. Be sure to operate by the control unit,

or external input device.

(6) Indoor room temperature sensor switching function

(OnlyforWiredremotecontroller)

The following settings are needed when using the Wired remote controller temperature

sensor.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

Yes 01

*Ifsettingvalueis“00”:

Room temperature is controlled by the indoor unit temperature sensor.

*Ifsettingvalueis“01”:

Room temperature is controlled by either indoor unit temperature sensor or remote

controller unit sensor.

(7) Wireless remote controller signal code

ChangetheindoorunitSignalCode,dependingonthewirelessremotecontrollers.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

B 01

C 02

D 03

(8) External input control

“Operation/Stop”modeor“Forcedstop”modecanbeselected.

(♦...Factorysetting)

Setting description

Function

number

Setting value

♦

Operation/Stopmode

(Settingforbidden) 01

Forced stop mode 02

Setting record

•

Record any changes to the settings in the following table.

Setting Setting Value

(1)Filtersign

(2)Staticpressure

(3)Coolingroomtemperaturecorrection

(4)Heatingroomtemperaturecorrection

(5)Autorestart

(6)Indoorroomtemperaturesensorswitchingfunc-

tion

(7)Wirelessremotecontrollersignalcode

(8)Externalinputcontrol

After completing the FUNCTION SETTING, be sure to turn off the power and turn it on

again.

SETTING THE ROOM TEMPERATURE DETECTION

LOCATION

The detection location of the room temperature can be selected from the following 2 examples.

Choosethedetectionlocationthatisbestfortheinstallationlocation.

A. Indoor unit setting (factory setting)

The room temperature is detected by the indoor unit temperature sensor

(1) WhentheTHERMOSENSORbuttonispressed,thelockdisplayashesbecausethe

function is locked at the factory.

Indoor unit

B. Indoor unit/remote controller setting (room tempera-

ture sensor selection)

The temperature sensor of the indoor unit or the remote controller can be used to detect

the room temperature.

(1) EnabletheroomtemperaturesensorselectioninFUNCTIONSETTING,whichwillbe

previous page.

(2) PresstheTHERMOSENSORbuttonfor5secondsormoretoselectthetemperature

sensor of the indoor unit or the remote controller.

Indoor unit

NOTES

IfthefunctiontochangethetemperaturesensorisusedasshowninexamplesA(other

thanexampleB),besuretolockthedetectionlocation.Ifthefunctionislocked,thelock

display

willashwhentheTHERMOSENSORbuttonispressed.

7.4. Jumper wire setting

(1) Drainage function setting (JM1)

If contained drainpumpisnotused,setthedrainagefunctionto“Invalid”inthedrainage

function switching.

Ifcontaineddrainpumpisnotuse:•

Whenusedunder“WALLMOUNTEDTYPE/FLOORSTANDINGCONCEALEDTYPE”.

Whenusedinnaturaldrainageunder“CEILINGCONCEALEDTYPE”.

(♦...Factorysetting)

JM1 Drainage function

♦

Connect Valid

Disconnect Invalid

(2) Auto louver grille setting (JM2) (Optional parts)

(♦...Factorysetting)

JM2 Auto louver grille setting

♦

Connect Invalid

Disconnect Valid

(3) Fan delay setting (JM3)

It is a function to delay the stop of cooling fan when the air conditioner is stopped.

(♦...Factorysetting)

JM3 Fan delay

♦

Connect Invalid

Disconnect Valid

• Switching position

JM3

JM2

JM1

Jumperwires

9374815173-04_IM.indb 14 9/21/2011 1:45:26 PM

En-15

7.5. Special installation methods

CAUTION

• WhensettingDIPswitches,donottouchanyotherpartsonthecircuitboarddirectly

with your bare hands.

• Besuretoturnoffthemainpower.

7.5.1. Group control system

CAUTION

• Groupcontrolcannotbeusedwhenusingitbythemultitype.

A number of indoor units can be operated at the same time using a single remote control-

ler.

(1) Wiringmethod(indoorunittoremotecontroller)



  

Indoor

unit 1

Bus wire

Remote

controller cable

Remote controller

When ground wire is necessary

Indoor

unit 2

Indoor

unit 3

Indoor

unit 4

(2) DIPswitchsetting(Indoorunit)

SettheunitnumberofeachindoorunitusingtheDIPswitchesontheindoorunit

circuitboard.(Seethefollowingtableandgure.)

TheDIPswitchesarenormallysettomaketheunitnumber00.

Indoor unit

Unit number

DIP SWITCH No.

1 2 3 4

00 OFF OFF OFF OFF

01 ON OFF OFF OFF

02 OFF ON OFF OFF

03 ON ON OFF OFF

04 OFF OFF ON OFF

05 ON OFF ON OFF

06 OFF ON ON OFF

07 ON ON ON OFF

08 OFF OFF OFF ON

09 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

7.5.2. Dual remote controllers

• 2separateremotecontrollerscanbeusedtooperatetheindoorunits.

•

The timer and self-diagnosis functions cannot be used on the slave units.

(1) Wiringmethod(indoorunittoremotecontroller)

Remote controller cable

Indoor unit

Remote controller

SlaveunitMasterunit

(2) RemotecontrollerDIPswitch1setting

 SettheremotecontrollerDIPswitch1No.2accordingtothefollowingtable.

Number of remote

controllers

Master unit Slave unit

DIP SW 1 No. 2 DIP SW 1 No. 2

1(Normal) OFF –

2(Dual) OFF ON

8. TEST RUN

CAUTION

• Alwaysturnonthepower12hourspriortothestartoftheoperationinordertoensure

compressor protection.

CHECK ITEMS

(1) Isoperationofeachbuttonontheremotecontrollernormal?

(2) Doeseachlamplightnormally?

(3) Donotairowdirectionlouversoperatenormally?

(4) Isthedrainnormal?

(5)

Isthereanyabnormalnoiseandvibrationduringoperation?

• Donotoperatetheairconditionerintestrunforalongtime.

[OPERATION METHOD]

• Fortheoperationmethod,refertotheoperatingmanual.

(1) Stoptheairconditioneroperation.

(2)

Pressthemastercontrolbuttonandthefancontrolbuttonsimultaneouslyfor2seconds

or more to start the test run.

Test run display

(3) Pressthestart/stopbuttontostopthetestrun.

If“C0”appearsintheunitnumberdisplay,thereisaremotecontrollererror.Refertothe

installation manual included with the remote controller.

Unit number Error code Content

Incompatible indoor unit is connected

Indoor unit

↔

remote controller communication

error

[Using the wireless remote controller for test run] (Option)

• Fortheoperationmethod,refertotheoperatingmanual.

•

The outdoor unit may not operate depending on the room temperature. In this case,

press the test run button on the wireless remote controller while the air conditioner is

running.(Pointthetransmittersectionofthewirelessremotecontrollertowardtheair

conditionerandpressthetestrunbuttonwiththetipofaball-pointpen,etc.)

Transmitter section

Test run button

•

Toendtestoperation,pressthewirelessremotecontrollerSTART/STOPbutton.

 (Whentheairconditionerisrunbypressingthetestrunbutton,theOPERATIONindicator

lampandTIMERindicatorlampwillsimultaneouslyashslowly.)

9374815173-04_IM.indb 15 9/21/2011 1:45:27 PM

En-16

9. OPTIONAL PARTS

]

WARNING

• 

Regulation of cable differs from each locality, refer in accordance with local rules.

This air conditioner can be connected with the following optional kits. Refer to each

installation manual for the method of installing optional parts.

• Wiredremotecontroller

• Simpleremotecontroller

• Externalconnectkit

• Remotesensorunit

• IRReceiverunit

• Autolouvergrille

9.1. Wired remote controller (Simple remote controller)

Pleasereferto[6.ELECTRICALWIRING]and[7.REMOTECONTROLLERSETTING].

9.2. External input and external output

Connection methods

Wiremodication:

Useatooltocut offtheterminal onthe endof the

wire, and then remove the insulation from the cut

end of the wire.

Connectthewirewithconnectingwirewithsolder.

Important:

Be sure to insulate the connection between the

wires.

• Connectionterminals

Outputterminal(CN103)

InputNoVoltageterminal(CN102)

• Wiringarrangement

Binder(Medium/Accessories)

Bind with this cable.

]

9.3. Remote sensor (Optional parts)

Connection method

• Connectionterminals

Remote sensor

terminal(CN8)

• Wiringarrangement

Binder(Medium/Accessories)

Bind with this cable.

• Removetheexistingconnectorandreplaceitwiththeremotesensorconnector(ensure

thatthecorrectconnectorisused).

• Theoriginalconnectorshouldbeinsulatedtoensurethatitdoesnotcomeintocontact

with other electrical circuitry.

Settingforroomtemperaturecorrection

When a remote sensor is connected, set the function setting of indoor unit as indicated

below.

• SetFunctionNumber“30”(Coolingroomtemperaturecorrection)to“01”

• SetFunctionNumber“31”(Heatingroomtemperaturecorrection)to“01”

9.4. IR Receiver Unit (Optional parts)

Connection method

• Connectionterminals

Receiver unit

terminal(CN13)

Optionalparts

Externalinput/

output wire

Insulated

connection

Cable

(Fieldsupply)

9374815173-04_IM.indb 16 9/21/2011 1:45:28 PM

En-17

• Wiringarrangement

Binder(Medium/Accessories)

Bind with this cable.

• Use7pinsforreceiverunitcable.

•

Atrst,connectthereceiverunitcabletotheReceiverunitterminal(CN13).

]

9.5. Auto louver grille (Optional parts)

Connection method

• Connectionterminalandjumperwires

Auto louver grille

terminal(CN11)

JM3

JM2

JM1

Jumperwires

• CutJumperwireJM2

• Wiringarrangement

Binder(Medium/Accessories)

Bushing(Accessoryofoptionalparts)

Bind with this cable.

Auto louver grille cable

Bushing(Accessory

ofoptionalparts)

Binder(Medium/Accessories)

Openingthis

knockout hole

]

9.6. Optional parts cable binding

Auto louver

grille cable

Remote controller

cable

Otheroptional

parts cables

Powersupply

cable

Avoid touching the

ceiling with the wiring.

*Useanaccessoryofindoorunitoroptionalpartsforbinder.

**Useanaccessoryofoptionalpartsforbushing.

Ceiling

Avoid covering the air

inlet with the wirings.

Binders*

Air inletBinder*

Knockout hole

Bushing**

• Donotbindthepowersupplycableandothercablestogether.

CAUTION

• To protect the cable insulation after opening a knockout hole, remove any burrs from

the edge of the hole.

10. CUSTOMER GUIDANCE

Explainthefollowingtothecustomerinaccordancewiththeoperatingmanual:

(1)Startingandstoppingmethod,operationswitching,temperatureadjustment,timer,air

owswitching,andotherremotecontrolleroperations.

(

2)Airlterremovalandcleaning,andhowtousetheairlouvers.

(3)Givetheoperatingandinstallationmanualstothecustomer.

(4)Ifthesignalcodeischanged,explaintothecustomerhowitchanged(thesystem

returnstosignalcodeAwhenthebatteriesintheremotecontrollerarereplaced).

*(4)isapplicabletousingwirelessremotecontroller.

9374815173-04_IM.indb 17 9/21/2011 1:45:28 PM

En-18

11. ERROR CODES

If you use a wired type remote controller, error codes will appear on the remote

controller display. If you use a wireless remote controller, the lamps on the IR receiver

unitwilloutputerrorcodesbywayofblinkingpatterns.Seethelampblinkingpatterns

and error codes in the table below. An error display is displayed only during operation.

Error display

Wired

remote

controller

Error code

Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)

●

(1)

●

(1)

◊

Serialcommunicationerror

●

(1)

●

(2)

◊

Wired remote controller

communication error

●

(1)

●

(5)

◊

Checkrununnished

●

(2)

●

(1)

◊

UnitnumberorRefrigerantcircuit

address setting error

[SimultaneousMulti]

●

(2)

●

(2)

◊

Indoor unit capacity error

●

(2)

●

(3)

◊

Combinationerror

●

(2)

●

(4)

◊

Connectionunitnumber •

error(indoorslaveunit)

[SimultaneousMulti]

Connectionunitnumbererror•

(indoorunitorbranchunit)

[FlexibleMulti]

●

(2)

●

(7)

◊

Masterunit,slaveunitset-up

error[SimultaneousMulti]

●

(3)

●

(2)

◊

IndoorunitPCBmodel

information error

●

(3)

●

(5)

◊

Manualautoswitcherror

●

(4)

●

(1)

◊

Room temp. sensor error

●

(4)

●

(2)

◊

IndoorunitHeatEx.Middletemp.

sensor error

●

(5)

●

(1)

◊

Indoor unit fan motor error

●

(5)

●

(3)

◊

Drain pump error

●

(5)

●

(7)

◊

Damper error

●

(5)

●

(15)

◊

Indoor unit error

●

(6)

●

(2)

◊

OutdoorunitmainPCBmodel

information error or

communication error

●

(6)

●

(3)

◊

Inverter error

●

(6)

●

(4)

◊

Activeltererror,PFCcircuit

error

●

(6)

●

(5)

◊

TripterminalLerror

●

(6)

●

(10)

◊

DisplayPCBmicrocomputers

communication error

●

(7)

●

(1)

◊

Discharge temp. sensor error

●

(7)

●

(2)

◊

Compressortemp.sensorerror

●

(7)

●

(3)

◊

OutdoorunitHeatEx.liquid

temp. sensor error

●

(7)

●

(4)

◊

Outdoortemp.sensorerror

●

(7)

●

(5)

◊

SuctionGastemp.sensorerror

●

(7)

●

(6)

◊

2-way valve temp. sensor error•

3-way valve temp. sensor error•

●

(7)

●

(7)

◊

Heatsinktemp.sensorerror

●

(8)

●

(2)

◊

Sub-coolHeatEx.gasinlet•

temp. sensor error

Sub-coolHeatEx.gasoutlet•

temp. sensor error

●

(8)

●

(3)

◊

Liquidpipetemp.sensorerror

●

(8)

●

(4)

◊

Currentsensorerror

●

(8)

●

(6)

◊

Discharge pressure sensor •

error

Suctionpressuresensorerror•

Highpressureswitcherror•

●

(9)

●

(4)

◊

Trip detection

●

(9)

●

(5)

◊

Compressorrotorposition

detectionerror(permanentstop)

●

(9)

●

(7)

◊

Outdoorunitfanmotorerror

●

(9)

●

(9)

◊

4-wayvalveerror

●

(10)

●

(1)

◊

Discharge temp. error

●

(10)

●

(3)

◊

Compressortemp.error

●

(10)

●

(4)

◊

Highpressureerror

●

(10)

●

(5)

◊

Lowpressureerror

●

(13)

●

(2)

◊

Branch boxes error

[FlexibleMulti]

Display mode

●

:0.5sON/0.5sOFF

◊

:0.1sON/0.1sOFF

():Numberofashing

[Troubleshooting at the remote controller LCD]

This is possible only on the wired remote controller.

[Self-diagnosis]

Ifanerroroccurs,thefollowingdisplaywillbeshown.(“Er”willappearinthesetroom

temperaturedisplay.)

Error code

EX.Self-diagnosis

9374815173-04_IM.indb 18 9/21/2011 1:45:32 PM

Fujitsu RDG12LLTA Installation guide

Brand: Fujitsu

Model: RDG12LLTA

Category: Split-system air conditioners

Type: Installation guide

Download PDF

report

Fujitsu RDG12LLTA Installation guide

Fujitsu RDG12LLTA Installation guide

Related papers

Other documents