LG PQRCVCL0Q User manual

Category
Split-system air conditioners
Type
User manual

This manual is also suitable for

ENGLISH
ITALIANO ESPAÑOL
FRANCAIS DEUTSCH
PORTUGUÊS
êìëëäàâ üáõä
www.lg.com
Please read this manual carefully before operating your set and retain it for future
reference.
SIMPLE WIRED REMOTE CONTROLLER
Original instruction
PQRCVCL0Q
PQRCVCL0QW
OWNER’S &
INSTALLATION MANUAL
AIR
CONDITIONER
[
Representative
]
LG Electronics Inc. EU Representative : LG Electronics European Shared Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen, The Netherlands
[
Manufacturer
]
LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro, Seongsan-gu, Changwon-si,
Gyeongsangnam-do, KOREA
Copyright © 2017 - 2020 LG Electronics Inc. All Rights Reserved.
MFL70261401
Rev.02_070720
2 Wired Remote Controller
Simple Wired Remote Controller Owner’s & Installation Manual
TABLE OF CONTENTS
n Safety Precautions..................................................................3
n Part Description ......................................................................4
Simple Wired Remote Controller...............................................................4
n Installation Instruction............................................................5
Remote controller installation ...................................................................8
Group control..............................................................................................9
Installer setting - How to enter installer setting mode ..........................10
Installer setting - Test Run Mode ............................................................12
Installer setting - Setting Address of Central Control...........................13
Installer setting - E.S.P.............................................................................14
Installer setting - Thermistor ..................................................................15
Installer setting - Ceiling Height Selection.............................................16
Installer setting - Static Pressure Setting ..............................................17
Installer setting - Remote Controller Master/Slave Setup.....................18
Installer Setting - Celsius / Fahrenheit Switching .................................19
Installer Setting - Celsius Control Setting..............................................20
Installer Setting - Setting for Refrigerant Leak Detector.......................21
Installer Setting - Static Pressure Step Setting .....................................22
Installer Setting - CN_EXT setting...........................................................23
Installer Setting - Auto ESP .....................................................................24
n Owners instruction ...............................................................26
Standard Operation - Cooling Mode .......................................................26
Standard Operation - Heating Mode .......................................................27
Standard Operation - Auto Operation Mode ..........................................28
Standard Operation - Dehumidification Mode .......................................29
Standard Operation - Fan Mode ..............................................................30
Function Setting - Fan Speed Selection .................................................31
Function Setting - Room temperature check .........................................32
Function Setting - Child Lock..................................................................33
Function Setting - Auto Swing ................................................................34
Function Setting - Vane Angle Control...................................................35
Different mode drive.................................................................................36
WLAN(Wireless LAN) Module Access Point Mode................................37
Self-diagnosis for Trouble Mode.............................................................38
Outage Compensation Function .............................................................38
Checkups before reporting breakdown..................................................39
Safety Precaution
Owner’s & Installation Manual 3
ENGLISH
Be sure to request to the
service center or installation
specialty store when
installing products.
• It will cause fire or electric shock
or explosion or injury.
Request to the service center
or installation specialty store
when reinstalling the
installed product.
• It will cause fire or electric shock
or explosion or injury.
Do not disassemble, fix, and
modify products randomly.
• It will cause fire or electric shock.
Do not place flammable
stuffs close to the product.
• It will cause fire.
Do not allow water to run
into the product.
• It will cause electric shock or
breakdown.
Do not give the shock to the
product.
• It will cause breakdown when
giving the shock to the product.
n Installation
Safety Precaution
• The installation requires expert skills, and it should be installed by the service center or other shops specialized
in the installation and recognized by our company.
• For all the problems arising after installation by someone who has no relevant qualifications, our company will
not provide free service.
• The following safety cautions are provided to prevent unexpected dangers or losses.
: If the user does not follow the mandatory items, it may result in serious injury or death.
: If the user does not follow the mandatory items, it may cause personal injury or property damage.
: Warning and Caution are to call the user’s attention to the possible danger. Read and follow them
carefully in order to prevent a safety accident.
: Warning and Caution are indicated in this guide and the product itself to help protect the users
from danger.
WARNING
CAUTION
WARNING
n In-use
Request to the service center or installation
specialty store when the product becomes wet.
• It will cause fire or electric shock.
Do not give the shock using sharp and
pointed objects.
• It will cause breakdown by damaging parts.
n In-use
CAUTION
Do not clean using the
powerful detergent like
solvent but use soft cloths.
• It will cause fire or product
deformation.
Do not press the screen
using powerful pressure or
select two buttons.
• It will cause product breakdown or
malfunction.
Do not touch or pull the lead
wire with wet hands.
• It will cause product breakdown or
electric shock.
n Installation
If anyone other than a licensed professional
installs, repairs, or alters LGElectronics air
conditioning products, the warranty is voided.
• All costs associated with repair are then the full
responsibility of the owner.
Do not install the unit in potentially
explosive atmospheres.
4 Wired Remote Controller
Part Description
Part Description
Accessory
Connecting Cable (1EA) Fixing Screw (2EA) Quick Guide
Simple Wired Remote Controller
Each function will be shown on the display panel for three seconds or so when the power is applied at first.
TEMP
FAN
SPEED
OPER
MODE
2
3
4
5
1
1. Operation Display Panel
2. Temperature Control Button
3. Fan Speed Button
4. On/Off Button
5. Operation Mode select Button
Owner’s & Installation Manual 5
ENGLISH
Installation instruction
1. Please fix tightly using provided screw after placing remote controller setup board
on the place where you like to setup.
- Please set it up not to bend because poor setup could take place if setup board bends.
Please set up remote controller board fit to the reclamation box if there is a reclamation box.
2. Can set up Wired remote controller cable into three directions.
- Setup direction: the surface of wall reclamation, upper, right
- If setting up remote controller cable into upper and right side, please set up after removing remote controller
cable guide groove.
h
Remove guide groove with long nose.
Reclamation to the surface of the wall
Upper part guide groove
Right part guide groove
Installation instruction
<Wire guide grooves>
Installation instruction
6 Wired Remote Controller
Wall
Side
Wall
Side
Wall
Side
Wall
Side
<Connecting order>
<Separating order>
3. Please fix remote controller upper part into the
backplate attached to the surface of the wall, as
the picture below, and then, connect with
backplate by pressing lower part.
- Please make sure to leave no gaps on the top, bottom, left or right
sides between the remote controller and backplate.
- Before assembly with the backplate, arrange the Cable not to
interfere with circuit parts.
Remove remote controller by inserting a
screwdriver into the lower separating holes and
twisting to release the controller from backplate.
- There are two separating holes. Please individually separate one
at a time.
- Please be careful not to damage the inside
components when separating.
4. Please refer to the following directions when connecting the indoor unit and the
wired remote controller together.
1) Please connect the cables as shown in the figure below when connecting the plug type cable from the
indoor unit’s C/BOX and the housing type of the extension cable.
2) When connecting Terminal Blocks of the indoor C/BOX and the wired remote controller with the extension
cable, refer to the steps below.
Remove the screw on the cable which is fastened to the wired remote controller’s Terminal Block by
loosening with a screw driver.
Remove the housing of the provided 32ft extension cable with a cutting nipper and peel it as shown in the
figure below. (when purchasing the extension cable at the site directly, please peel it as shown in the figure
below.)
Please check if the connectors are connected properly.
C/BOX Cable (Plug type)
Extension cable(housing type)
Indoor
Unit side
TEMP
FAN
SPEED
OPER
MODE
• Specification of LG supplied extension cable: AWG#22, 3 core shielded. (Model : PZCWRC1)
h Apply enclosed noncombustible conduit(metal raceway) totally or use FT-6 rated cable or above level in
case of local electric & building code that requires plenum (CMP) cable usage.
CAUTION
Signal Yellow
12V Red
GND Black
1.378 inch(35mm)
±0.197 inch(5mm)
0.394 inch(10mm) ± 0.118 inch(3mm)
Owner’s & Installation Manual 7
ENGLISH
Installation instruction
5. Please use an extension cable if the distance between the wired remote controller
and the indoor unit is longer than 32ft(10m).
Make sure each wire is securely fastened under each screw terminal and the wires are not in contact with
each other.
Please connect the Terminal blocks of indoor unit’s C/BOX and wired remote controller by referring to the
images and contents shown below.
Connect the yellow(signal) part of the wired remote controller’s terminal block and the ‘YL’ part of the indoor
unit’s terminal block.
Connect the red(12V) part of the wired remote controller’s terminal block and the ‘RD’ part of the indoor
unit’s terminal block.
Connect the black(GND) part of the wired remote controller’s terminal block and the ‘BK’ part of the indoor
unit’s terminal block.
h In case of loosened screws or insufficient contact between the terminal and the wire, remote controller
may not function properly.
h When the power is off on the remote controller, check the connection between the remote controller and
Terminal Block.
h Use an appropriate screwdriver for tightening the terminal screws. A screwdriver with a small head will
strip the head and make proper tightening impossible.
h Over-tightening the terminal screws may break wires and terminal block structure.
<Remote controller> <Indoor Terminal Block>
• Installation work must be performed in accordance with the national wiring standards and local by
authorized personnel only.
• Installations must comply with the applicable local/national or international standards.
• AWG#22, 3 core shielded is recommended when using the large hole in the center of the back plate.
• AWG#24, 3 core shielded is recommended when using the side or top knock-out of the back plate.
CAUTION
When installing the wired remote controller, do not bury it in the wall.
(It can cause damage in the temperature sensor.)
Do not install the cable to be 164ft(50m) or longer. (It can cause communication error.)
CAUTION
Remote controller
PCB Terminal
block Remark
Indoor
Terminal
block
Function
YELLOW YL Signal
RED RD 12V
BLACK BK GND
Installation instruction
Remote controller installation
Since the room temperature sensor is in the remote controller, the remote controller box
should be installed in a place away from direct sunlight, high humidity and direct supply of
cold air to maintain proper space temperature. Install the remote controller about 5ft(1.5m)
above the floor in an area with good air circulation at an average temperature.
Do not install the remote controller where it can be affected by:
- Drafts, or dead spots behind doors and in corners.
- Hot or cold air from ducts.
- Radiant heat from sun or appliances.
- Concealed pipes and chimneys.
- Uncontrolled areas such as an outside wall behind the remote controller.
- This remote controller is equipped with LCD display. For proper display of the remote
controller LCD's, the remote controller should be installed properly as shown in Fig.1.
(The standard height is 4~5 ft (1.2~1.5 m) from floor level.)
8 Wired Remote Controller
TEMP
FAN
SPEED
OPER
MODE
TEMP
FAN
SPEED
OPER
MODE
TEMP
FAN
SPEED
OPER
MODE
TEMP
FAN
SPEED
OPER
MODE
5feet
(1.5meters)
(Fig. 1)
Direct
Sun ray contact area
no
no
no
yes
Owner’s & Installation Manual 9
ENGLISH
Installation instruction
GND
GND
12V
Signal wire
Signal wire
TEMP
FAN
SPEED
OPER
MODE
GND
12V
B Y R B Y R
MASTER SLAVE
Signal wire
GND
12V
Signal wire
TEMP
FAN
SPEED
OPER
MODE
TEMP
FAN
SPEED
OPER
MODE
Group control
1. When installing more than 2
units of air conditioner to one
wired remote controller, please
connect as the right figure.
• If it is not event communication
indoor unit, set the unit as slave.
• Check for event communication
through the product manual.
2. When installing more than 2 wired
remote controllers to one air
conditioner, please connect as the
right picture.
• When installing more than 2 units of wired
remote controller to one air conditioner, set
one wired remote controller as master and
the others all as slaves, as shown in the
right picture.
• You cannot control the group as shown in
the right for some products.
Refer to the product manual for more detail.
When controlling multiple indoor units with event communication function with one remote
controller, you must change the master/slave setting from the indoor unit.
Indoor units, the master/slave configuration of the product after completion of indoor unit power
‘OFF’ and then ‘ON’ the power after 1 minutes elapsed sign up.
- For ceiling type cassette and duct product group, change the switch setting of the indoor PCB.
- For wall-mount type and stand type product, change the master/slave setting with the wireless
remote controller. (Refer to wireless remote controller manual for detail)
h When installing 2 remote controllers to one indoor unit with event communication function, set
the master/slave of the remote controller. (Refer to remote controller master/slave selection)
When controlling the group, some functions excluding basic operation setting, fan level
Min/Mid/Max, remote controller lock setting and time setting may be limited.
<When simultaneously connecting
2 sets of wired remote controller>
• When controlling in groups, set the master/slave of the remote controller. Refer to Installer
setting section on how to set master/slave for more detail.
12345678 12345678
#3 switch OFF: Master
(Factory default setting)
#3 switch ON: Slave
10 Wired Remote Controller
Installation instruction
<Installer Setting Code Table>
1) General air-conditioner product
j Some contents may not be displayed depending on the product function
Installer setting mode is to set the detail function of the remote controller.
If the installer setting mode is not set correctly, it can cause problems to the product, user injury or property
damage. This must be set by an certificated installer, and any installation or change that is carried out by a
non-certificated person should be responsible for the results. In this case, free service cannot be provided.
CAUTION
Installer Setting - How to enter installer setting mode
TEMP
FAN
SPEED
OPER
MODE
Function Code
Value
If you want to set installer setting mode, press
the temperature up button and the oper mode
button same time for five seconds.
1
When you enter the setting mode initially.
Function code is displayed on the LCD screen.
2
No. Function Code Value
1 Test Run 01 01:Set
2 Address Setting 02 00~FF : Address
<ESP Step> <ESP Value> <Example>
01:VeryLow 0 ~ 255
02:Low
3 E.S.P. Value 03
03:Med
04:High
05:Very High
01:Remo
4 Thermistor 04 02:Indoor
03:2TH
01:Med
02:Low
5 Ceiling Height 05
03:High
04:Very High
01:V-H
02:F-H
6 Static Pressure 06
03:V-L
04:F-L
7 Master Setting 07
00:Slave
01:Master
8
Celsius
12
00:Celsius
(Optimized only for U.S.A)
Fahrenheit Switching 01:Fahrenheit
9 Celsius Control 17
00 : 1 °C Control
01 : 0.5 °C Control
10
Refrigerant
29
00 : Not installed
Leak Detector 01 : Installed
11
Static Pressure
32
00: use static pressure (code 06) set value
Step 01~ 11: static pressure step (code 32) set value
Function Code ESP valueESP step
Owner’s & Installation Manual 11
ENGLISH
Installation instruction
<Installer Setting Code Table>
1) General air-conditioner product
No. Function Code Value
12 CN_EXT setting 52
00: Not use
01: Simple operation On/Off
02: Simple dry contact (It takes HL when operation is off.)
03: Indoor unit single emergency stop
04: Occupied / unoccupied
05: Indoor unit all emergency stop
※It can be set only when there is indoor unit emergency stop
function.
06: Window contact
※It can be set only when there is window contact function.
07: Window contact lock
※It can be set only when there is window contact lock function.
13 Auto ESP 68
0: Not use
1: Auto
200: Manual (190 V)
201: Manual (200 V)
202: Manual (210 V)
203: Manual (220 V)
204: Manual (230 V)
205: Manual (240 V)
206: Manual (250 V)
207: Manual (260 V)
208: Manual (270 V)
3: Pass
4: Fail
12 Wired Remote Controller
Installation instruction
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered
into the installer setting mode.
- After entering into the installer setting
mode, select the test run mode code
value by pressing the button.
* Test run mode code value : 01
1
When pressing the button, the test
operation mode will be performed, and it
is displayed as shown in the left figure.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be
released.
- If there isn’t any button input for more
than 25 seconds, the installer setting
mode will also be released.
3
When approx. 18 minutes are elapsed
after starting of the test oper-mode, the
system will be stopped automatically
and converted to the standby state.
- If any button is inputted during the test
run mode, the test run mode will be
forced to be relreased.
4
OPER
MODE
OPER
MODE
OPER
MODE
OPER
MODE
Installer Setting - Test Run Mode
After installing the product, you must run a Test Run mode.
For details related to this operation, refer to the product manual.
What is the test run mode??
- This means the operation of the product under the cooling, strong wind, and Comp on state
without performing room temperature control in order to confirm the installed state during the
product installation.
Owner’s & Installation Manual 13
ENGLISH
Installation instruction
* In the case when the lock is set up at the central controller, ‘HL’ will be indicated on the display
window of the wired remote controller and the indoor unit will not be controlled by the remote
controller.
It's the function to use for connecting central control.
Please refer to central controller manual for the details
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into the
installer setting mode.
-
After entering into the installer setting mode,
select the central control address setting
code value by pressing the button.
* Setting address of central control code
value : 02
1
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more than
25 seconds, the installer setting mode will
also be released.
4
Set up the group number and indoor unit with
the temperature adjustment(,) buttons.
For example, when setting as
[ Group number=2 Indoor number=3 ]
it will be displayed as shown in the left figure.
2
OPER
MODE
OPER
MODE
TEMP
Group number
Indoor unit number
Press button to save the setting.
3
OPER
MODE
Installer Setting - Setting Address of Central Control
• If you connect the indoor unit to the central controller, you should set the network address
of the indoor unit so that the central controller could recognize it.
• The center-control address is composed of the group number and the indoor-unit number.
Note : The remote controller displays 'HL' if central controller has locked the remote controller .
14 Wired Remote Controller
Installation instruction
Installer Setting - E.S.P.
• If you set ESP incorrectly, the air conditioner may malfunction.
• This setting must be carried out by a certificated-technician.
This is the function that decides the strength of the wind for each wind level and because this
function is to make the installation easier.
Precaution shall be taken not to alter the E.S.P value corresponded to each air flow section.
E.S.P value can be varied according to the products.
In the case of going to the next air flow rate stage by pressing the fan-speed button during the
setup of the E.S.P value, the E.S.P value of previous air flow rate will be maintained by
remembering the E.S.P value prior to the shift.
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into
the installer setting mode.
- After entering into the installer setting
mode, select the E.S.P code value by
pressing the button.
* E.S.P code value : 03
1
Select the desired air flow rate with
the button. Whenever pressing
the button, [SLO
LO
MED
HI
POW] will be indicated.
2
Select the desired air flow rate value
with the temperature up(), down()
button.
* E.S.P value range : 0~255
-
E.S.P value will be indicated at the upper
right section of the display window.
3
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more
than 25 seconds, the installer setting
mode will also be released.
5
OPER
MODE
OPER
MODE
FAN
SPEED
FAN
SPEED
OPER
MODE
Press button to save the setting.
4
Owner’s & Installation Manual 15
ENGLISH
Installation instruction
• As the characteristic of the ‘2TH’ function can be different in accordance with the
products, refer to the product instruction manual for its detail.
Installer Setting - Thermistor
This is the function to select the temperature sensor to judge the room temperature.
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into
the installer setting mode.
- After entering into the installer setting
mode, select the thermistor sensor
setting code value by pressing the
button.
* Thermistor sensor selection code
value : 04
1
Select the desired setting value with the
temperature up(), down() button.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be
released.
- If there isn’t any button input for more
than 25 seconds, the installer setting
mode will also be released.
4
OPER
MODE
OPER
MODE
Code value
*Setting value
01: Remote
controller
02: Indoor unit
03: 2TH
OPER
MODE
Value
Press button to save the setting.
3
16 Wired Remote Controller
Installation instruction
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into
the installer setting mode.
- After entering into the installer setting
mode, select the ceiling height setting
code value by pressing the button.
* Ceiling height setting code value : 05
1
Select the desired setting value with the
temperature up(), down() button.
2
Press button to save the setting.
3
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more
than 25 seconds, the installer setting
mode will also be released.
4
OPER
MODE
OPER
MODE
Code value
*Setting value
01: Low
02: Standard
03: High
04: Very high
OPER
MODE
Value
Installer Setting - Ceiling Height Selection
This function is to adjust FAN Airflow rate according to ceiling height (For ceiling type product)
Ceiling height setting is available only for some products.
Ceiling height of ‘Very high’ function may not exist depending on the indoor unit.
Refer to the product manual for more details.
Ceiling Height Level Description
01 Low Decrease the indoor airflow rate 1 step from standard level
02 Standard Set the indoor airflow rate as standard level
03 High Increase indoor airflow rate 1 step from standard level
04 Very high Increase indoor airflow rate 2 steps from standard level
<Ceiling Height Selection Table>
• As the ceiling height setting standard can
be different in accordance with the
products, refer to the product instruction
manual for its detail.
Owner’s & Installation Manual 17
ENGLISH
Installation instruction
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into
the installer setting mode.
-
After entering into the installer setting mode,
select the static pressure setting code value
by pressing the button.
* Static pressure setting code value : 06
1
Select the desired setting value with the
temperature up(), down() button.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more than
25 seconds, the installer setting mode will
also be released.
4
OPER
MODE
OPER
MODE
Code value
*Setting value
01:V-H
02:F-H
03:V-L
04:F-L
Press button to save the setting.
3
OPER
MODE
Value
Installer Setting - Static Pressure Setting
This function is applied to only duct type. Setting this in other cases will cause malfunction.
Pressure selection
Function
Zone state ESP standard value
01 V-H Variable High
02 F-H Fixed High
03 V-L Variable Low
04 F-L Fixed Low
<Static Pressure Setting Table>
18 Wired Remote Controller
Installation instruction
Installer Setting - Remote Controller Master/Slave Setup
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into the
installer setting mode.
-
After entering into the installer setting mode,
select the remote controller master / slave
setting code value by pressing the button.
* Remote controller master/slave setting
code value : 07
1
Select the desired setting value with the
temperature up(), down() button.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more than
25 seconds, the installer setting mode will
also be released.
4
OPER
MODE
OPER
MODE
Code value
*Setting value
00:Slave
01:Master
OPER
MODE
Value
Press button to save the setting.
3
It is a function for settings in group control, or 2-remote controller control.
Remote controller Function
Master
Indoor unit operates based on master remote controller at group control.
(Master is set when delivering from the warehouse.)
Slave
Setup all remote controllers except one master remote controller to slave at
group control
When controlling in groups, basic operation settings, airflow strength weak/medium/strong,
lock setting of the remote controller, time settings, and other functions may be restricted.
h Refer to the 'group control' part for details
Owner’s & Installation Manual 19
ENGLISH
Installation instruction
• Whenever press temp up(s), down(t) button in Fahrenheit mode, the temperature will
increase/drop 2 or 1 degrees.
Installer Setting - Celsius / Fahrenheit Switching
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into the
installer setting mode.
-
After entering into the installer setting mode,
select the Celsius / Fahrenheit setting code
value by pressing the button.
* Celsius/Fahrenheit setting code value : 12
1
Select the desired setting value with the
temperature up(), down() button.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more than
25 seconds, the installer setting mode will
also be released.
4
OPER
MODE
OPER
MODE
Code value
*Setting value
00:Celsius
01:Fahrenheit
OPER
MODE
Value
Press button to save the setting.
3
This function is used for switching the display between Celsius and Fahrenheit.
(Optimized only for U.S.A)
20 Wired Remote Controller
Installation instruction
Installer Setting - Celsius Control Setting
TEMP
FAN
SPEED
OPER
MODE
When pressing the button and
button simultaneously for more than 3
seconds, the system will be entered into the
installer setting mode.
-
After entering into the installer setting mode,
select the celsius control setting code value by
pressing the button.
* Celsius control setting code value : 17
1
Select the desired setting value with the
temperature up(), down() button.
2
When pressing the button and
button simultaneously for more than 3
seconds after the setting has been
completed, the setting mode will be released.
- If there isn’t any button input for more than
25 seconds, the installer setting mode will
also be released.
4
OPER
MODE
OPER
MODE
Code value
* Setting value
00 : 1 °C Control
01 : 0.5 °C Control
OPER
MODE
Value
Press button to save the setting.
3
This function is to set the unit for temperature control by 1°C or 0.5°C.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

LG PQRCVCL0Q User manual

Category
Split-system air conditioners
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI