Glacier Bay HD67420-3101 Installation guide

Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

THANK YOU
INSTALLATION AND CARE GUIDE
TWO-HANDLE ROMAN TUB FAUCET
We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this roman tub
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
9/2016 REV.01YOW
Model#
HD67420-3101
HD67420-3104
HD67420-3127D
SKU#
000000
000000
000000
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Phillips
screwdriver
Basin
wrench
2
Table of Contents
Important Information ..............................2
Warranty ...................................................2
Pre-Installation .........................................2
Planning Installation ..............................2
Package Contents ..................................3
Installation ................................................4
Care and Cleaning ....................................7
Troubleshooting ........................................7
Service Parts
...........................................
8
Important Information
Observe all local plumbing and building codes.
Cover the sink drain to avoid losing any parts.
Review the care and cleaning section included in this guide.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact customer service
for replacement parts.
TOOLS AND HARDWARE REQUIRED
Adjustable
wrench
Safety
goggles
(2) Supply
lines
Tools and Hardware Required ...............2
Operation...................................................7
Warranty
LIMITED LIFETIME WARRANTY
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that prove defective.
Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-
5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer
purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for
more details.
3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
D Protective cap 1
E Connector 1
F 1
G Rubber washer 1
Middle body
H Metal washer 1
I Mounting nut 1
J Index 2
K Screw 2
Part Description Quantity
A Spout assembly 1
B Set screw 1
C 3.2mm hex wrench 1
O Flange 2
P Hot end valve 1
Q 1
R Rubber washer 2
Cold end valve
S Metal washer 2
T Mounting nut 2
U Hose 2
L Handle 2
M Flange 2
N Protective cap 2
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
D
E
F
G
H
I
U
P
N
A
B
C
J
K
L
M
O
Q
R
S
T
4
Installation
1
Preparing for installation
CAUTION: Always turn off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
2
Removing the protective cap
Remove the protective cap (D). Loosen the
connector (E) from the middle body (F). Adjust
the rubber washer (G), metal washer (H) and
mounting nut (I) to the bottom of middle body (F).
Shut off the water supply. Remove the old
faucet.
Clean the mounting surface.
Drill 1-3/8 in. holes in the nished deck as
shown in the diagram below.
5 in. min.
8~16 in.
3 in. min.
1-1/4 in. MAX. DECK THICKNESS
1-3/8 in.
Diamter
1-1/8 in.
Diamter
1-3/8 in.
Diamter
NOTE: This kit allows up to 1-1/4 in. deck thickness.
3
Installing the middle body
From underneath the deck, insert the middle
body (F) with the rubber washer (G), metal
washer (H) and mounting nut (I) through the
mounting hole.
From above, thread the connector (E) onto
the middle body (F).
Tighten the mounting nut (I) using a basin
wrench, so that the connector (E) sits ush
against the nished deck surface.
D
E
F
G
H
I
E
F
G
H
I
5
Installation (continued)
4
Removing the protective caps
Remove the protective caps (N). Loosen the
anges (O) from the valve bodys (P & Q). Adjust
the rubber washers (R), metal washers (S) and
mounting nuts (T) to the bottom of valve
bodys (P & Q).
5
Installing the valve bodies
From underneath the deck, insert the cold end
valve (Q) with the rubber washer (R), metal
washer (S) and mounting nut (T) through
the hole on the right (cold) side.
From above, thread the ange (O) onto the
valve body (Q).
Tighten the mounting nut (T) using a basin
wrench, so that the ange (O) sits ush against
the nished deck surface.
Repeat this procedure for the hot end valve (P)
on the left (hot) side.
6
Connecting the hoses
Connect the hoses (U) to the bottom of the hot
and cold end valves (P & Q), as shown.
Align the middle body (F) in a position that will
allow maximum clearance to connect the
hoses (U).
Carefully bend the hoses (U) to t in the
available space, and carefully thread the hose
(U) couplings onto the sides of the middle
body (F). Tighten all connections with a wrench.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
Q
R
S
T
N
O
P
N
O
R
S
T
P
Q
R
S
T
O
U
Q
P
F
U
NOTE: The hot end valve is identied with a label.
6
Installation (continued)
7
Installing the spout assembly
Install the spout assembly (A) onto the
connector (E). Be sure the spout assembly (A)
is resting rmly on the deck.
Push down on spout assembly (A) and tighten
set screw (B) with the Hex wrench
(Hex: 3.2mm, C).
8
Installing the handle
Thread the ange (M) onto the ange (O). Place
the handle (L) onto the cartridge stem (1) and
tighten with the screw (K). Insert the index (J).
9
Making the water supply
connections
Connect the water supply lines (1) to the
faucet inlets (2). (Supply lines are not
included.)
Place the other handle onto the left (hot) valve
and install the same way.
1
2
C
A
B
E
1
J
K
L
M
O
7
Operation
1
Flushing and checking for leaks
Ensure the faucet handles are in the off position,
and turn on the water supply and check for leaks.
If you discover any leaks, check your connections
to ensure they are installed properly.
Turn on the hot and cold handles to allow the
water to run for at least one minute. This
ushes away any debris that could cause
damage to internal parts.
Turn off the water.
Care and Cleaning
To clean, wipe down with a damp cloth and dry with a towel.
Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will
be voided.
Troubleshooting
Problem Possible Cause Solution
There are leaks from the
handle.
The bonnet nut has come loose and/or the
washer is dirty or damaged.
Tighten the bonnet nut.
Clean or replace the washer.
The water will not shut off
completely.
The cartridge is dirty or broken. Remove the handle to check
the cartridge.
Clean or replace.
NOTE: Refer to the service parts section in this manual for
a detailed drawing showing the location of the parts listed
below.
There is a leak from the
spout base when the
faucet is on.
The o-ring which is on the connector
under the spout is worn.
Remove the spout and replace
a new o-ring.
HOMEDEPOT.COM
Please contact 1-855-HD-GLACIER for further assistance.
8
Service Parts
*Specify Finish
Faucet ID tags can be
found by removing
the hot water handle
17 Rubber washer RP64035
Part Description Part Number
O-ring RP60094
Part Description Part Number
15
16
Connector RP70459
1
RP10001*
2 Index C RP10002*
3
4
5
6
Handle RP13528*
7
Flange RP80451*
8
Flange
RP70342
Index H
13
Bonnet nut RP70001
9
11
12
14
Cartridge H
RP20067
Cartridge C RP20068
10 Rubber washer RP64023
Mounting nut RP56014
Set screw RP50054
Screw RP50005
Metal washer RP64024
O-ring RP60056
Hose RP70042
19
20
Mounting nut RP56087
18 Metal washer RP64036
Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM
16
17
18
19
20
1
2
3
4
5
6
7
8
9
10
11
12
13
15
14
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM
Retain this manual for future use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

Glacier Bay HD67420-3101 Installation guide

Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI