NICOR NUC-4-30-DM-L-WH Installation guide

NUC-4-30-DM-L-WH
NICOR
Brand
NICOR
Model
NUC-4-30-DM-L-WH
Category
Wall & ceiling mounts accessories
Type
Installation guide
LED NUC-4 Linkable
INSTALLATION INSTRUCTIONS
What’s In The Box Optional Accessories
Tools Needed
Type A
One (1) LED Under Cabinet
Splice
(White, Black)
Jbox
(White, Black)
Connector
(White, Black)
Plug
(White, Black)
Jumper
(6”, 12”, 24”, 72”) (White, Black)
This LED Under Cabinet requires very few tools
for installation. A Phillips Head Screwdriver will be
needed to install the xture to cabinetry.
CAUTION
1. Read all instructions carefully for safe operation and installation.
2. To avoid possible electrical shock, shut o electricity before the installation.
3. All wiring must be in accordance with national and local electrical codes. Installation work and electrical
wiring must be done by a qualied electrician.
4. Do not install over a heat source.
Note: Power will always come in on switch side of under cab.
Match ( ) symbols for proper
Type B connection
Match ( ) symbols for proper
Type A connection
Type B
Match
Symbol
Match
Symbol
Linkable Diagram
Match symbols to ensure correct connections are being made.
Match
Symbol
Match
Symbol
Top view of Under Cab
Side view of Under Cab
Side view of Under Cab
Model Electrical Rating Max Units Max Distance Between Units
NUC-4-08-DM-L-## 120 Vac, 60 Hz, 0.038A
30 72”
NUC-4-12-DM-L-## 120 Vac, 60 Hz, 0.057A
NUC-4-21-DM-L-## 120 Vac, 60 Hz, 0.083A
NUC-4-30-DM-L-## 120 Vac, 60 Hz, 0.110A
NUC-4-40-DM-L-## 120 Vac, 60 Hz, 0.145A
Power on the xtures to enjoy your new accent lighting.
4
1c
Power (Jbox):
Choose access points in the Jbox where power in and power out is preferred.
Make wiring connections (see wiring instructions below).
Jbox
Black (Line)
White (Neutral)
Green (Grd)
Black (Line)
White (Neutral)
Green (Grd)
120V Only splice accessory to Under Cab
Note: Only use splice accessory for J-box to Under Cab connection
Mounting Under Cabinet:
Mount the under cabinet to surface using the (2) provided captive
screws. Mount additional under cabinets within 72”.
(step 1b-1c only required if using Jbox in installation)
Mounting Jbox:
Mount Jbox to surface using provided screws within 72” of rst
under cabinet mounted.
1a
1b
Installing Under Cabinets
Note: On 30” & 40” under cabinets an additional mounting hole is located in the center of
the wiring trough.
Reference linkable Diagram to ensure
correct end is being plugged in.
3a
Power (Plug):
Ensure that all interconnected units are connected before
supplying power. Ensure that the power switch of each unit is
set to o, then plug the power plug into wall socket.
Linkable Cord Installation:
Remove power port cover from end of fixture then connect linkable
cord to under cabinet.
2
Note: If installing multiple xtures, use jumper accessory to
connect xtures together.
  • Page 1 1
  • Page 2 2

NICOR NUC-4-30-DM-L-WH Installation guide

NUC-4-30-DM-L-WH
NICOR
Brand
NICOR
Model
NUC-4-30-DM-L-WH
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents