Samsung SDM-090P Owner's manual

Type
Owner's manual
Part No.: AB68
-00125A
Printed in Korea
SDM-090(P) Cover 6/26/01 5:47 PM Page 1
1
2
3
4
5
9
678
USER’S MANUAL
DIGITAL MULTIPLEXER
SDM-090(P) Cover 6/26/01 5:47 PM Page 2
Digital Multiplexer
SDM – 090(P)
USER’S MANUAL
SDM-090(P)A 6/26/01 5:46 PM Page 1
Digital Multiplexer SDM-090(P)
iii
Graphic Symbol Explanation
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
Warning-To Prevent Fire or Shock Hazard,
Do Not Expose This Equipment To Rain or Moisture.
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SDM-090(P)A 6/26/01 5:46 PM Page iii
iv
Digital Multiplexer SDM-090(P)
IMPORTANT SAFEGUARDS
1. Read instructions: All the safety and operating instructions should be read
before the appliance is operated.
2. Retain instructions: The safety and operating instructions should be retained
for future reference.
3. Heed warnings: All warnings on the appliance and in the operating instructions
should be adhered to.
4. Follow instructions: All operating and use instructions should be followed.
5. Cleaning: Unplug this video product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments: Do not use attachments not recommended
by the video product manufacturer as they may cause hazards.
7. Water and moisture: Do not use this video product near
water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and the like.
8. Accessories : Do not place this video product on an unstable cart, stand, tripod,
bracket, or table.
The video product may fall, causing serious injury
to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the video product.
Any mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer.
SDM-090(P)A 6/26/01 5:46 PM Page iv
v
Digital Multiplexer SDM-090(P)
8A. An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation : Slots and openings in the cabinet are provided for ventilation and to
ensure reliable operation of the video product and to protect it from overheating,
and these openings must not be blocked or covered. The openings should never
be blocked by placing the video product on a bed, sofa, rug, or other similar
surface. This video product should never be places near or over a radiator or heat
register. This video product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the manufacturer's
instructions have been adhered to.
10. Power sources : This video product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your appliance dealer or local power
company. For video products intended to operate from battery power, or other
sources, refer to the operating instructions.
11. Power-Cord Protection : Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
12. Lightning : For added protection for this video product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system. This will prevent damage to the
video product due to lightning and power-line surges.
13. Overloading : Do not overload wall outlets and extension cords as this can result
in a risk of fire or electric shock.
SDM-090(P)A 6/26/01 5:46 PM Page v
vi
Digital Multiplexer SDM-090(P)
14. Object and liquid entry : Never push objects of any kind into this video product
through openings as they may touch dangerous voltage points or short-out parts
that could result in a fire or electric shock. Never spill liquid of any kind on the
video product.
15. Servicing : Do not attempt to service this video product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
16. Damage requiring service : Unplug this video product from the wall outlet and
refer servicing to qualified service personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instruction, as an improper adjustment of other
controls may result in damage and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
e. If the video product has been dropped or the cabinet has been damaged.
f. When the video product exhibits a distinct change in performance this indicates
a need for service.
17. Replacement parts : When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
18. Safety Check : Upon completion of any service or repairs to this video product,
ask the service technician to perform safety checks to determine that the video
product is in proper operating condition.
SDM-090(P)A 6/26/01 5:46 PM Page vi
Digital Multiplexer SDM-090(P)
vii
CONTENTS
CHAPTER 1. INTRODUCTION ......................................1-1~1-6
Introduction.......................................................................................................1-1
Functions and Features....................................................................................1-1
Name of parts and Function.............................................................................1-3
Front panel .......................................................................................................1-3
Rear panel........................................................................................................1-5
CHAPTER 2. INSTALLATION ........................................2-1~2-5
Preparing for the Installation ............................................................................2-1
Precautions when Installing .............................................................................2-2
Unpacking.........................................................................................................2-5
CHAPTER 3. CONNECTING TO OTHER DEVICES.....3-1~3-6
Connecting to normal VCR and Monitor..........................................................3-1
Connecting to S-VHS VCR and S-VHS MONITOR.........................................3-2
Connecting to TIME LAPSE VCR....................................................................3-3
Connecting to ALARM sensor..........................................................................3-4
Remote Control by connecting to PC...............................................................3-5
Connecting to RS-232C..........................................................................3-5
RS-232C 9 PIN.......................................................................................3-5
SDM-090(P)A 6/26/01 5:46 PM Page vii
CHAPTER 4. BASIC METHOD TO USE.......................4-1~ 4-7
Initial operation.................................................................................................4-1
When desiring to see in the live screen/replay screen....................................4-2
When desiring to see in the TRIPLEX screen .................................................4-2
When desiring to see in the FULL screen........................................................4-2
When desiring to see in the division screen.....................................................4-3
When desiring to see automatic sequential conversion screen ......................4-4
When desiring to see the stop screen..............................................................4-5
When desiring to see in the zoom screen........................................................4-6
When desiring to see in the PIP screen...........................................................4-6
When desiring to see in the record screen ......................................................4-7
When desiring to see output of VCR as it is ....................................................4-7
CHAPTER 5. SETTING OF PROGRAM MENU .........5-1~ 5-12
Record setting of each camera........................................................................5-1
Setting of display mode....................................................................................5-3
Setting of title by channel.................................................................................5-7
Setting of display mode for current time, year, month and date......................5-8
Setting of alarm ................................................................................................5-9
System setting................................................................................................5-10
viii
Digital Multiplexer SDM-090(P)
SDM-090(P)A 6/26/01 5:46 PM Page viii
CHAPTER 6. RECORDING............................................6-1~6-3
Normal record mode.........................................................................................6-1
TIME LAPSE record mode...............................................................................6-2
Weight value (REC DUTY) record...................................................................6-2
ALARM weight value record.............................................................................6-3
Reservation record...........................................................................................6-3
CHAPTER 7. OCCURRENCE AND HANDLING OF ALARM,
LOSS ...............................................................................7-1~7-4
Alarm occurrence conditions............................................................................7-1
Alarm release ...................................................................................................7-1
Screen conversion............................................................................................7-1
Alarm record.....................................................................................................7-1
Alarm signal standard.......................................................................................7-2
Alarm/Loss list reference..................................................................................7-3
Operation in video loss.....................................................................................7-4
APPENDIX A SPECIFICATIONS..................................A-1~A-3
Specifications...................................................................................................A-1
Outside drawing...............................................................................................A-3
APPENDIX B CHECKING POINTS IN TROUBLE .......B-1~B-2
ix
Digital Multiplexer SDM-090(P)
SDM-090(P)A 6/26/01 5:46 PM Page ix
CHAPTER 1
Introduction
SDM-090(P)A 6/26/01 5:46 PM Page x
1-1
Digital Multiplexer SDM-090(P)
CHAPTER 1.INTRODUCTION
Introduction
This unit can combine up to 9 Camera Images onto one VCR, and both
frequent recording and sequential recording can be possible in the unit of
Frame and Field, and assigned channel can be played back selectively, and it
is Triplex with which Live Mode, Playback Mode, and Live plus Playback Mode
can be done in one monitor.
Functions and Features
¥ System Setup Menu Button allows you to configure the system the way you
want.
¥ Up to 9 asynchronous camera images (color or black/white) can be
connected.
¥ Up to 9 camera images can be combined onto one monitor so that
multi-screen viewing is made possible.
¥ Multi-view screen which supports simultaneous viewing of live cameras
during playback of recorded scenes
¥ 4xzoom is allowed
¥ Using Spot Output, specific screen can be monitored.
¥ With Freeze Function, you can view a still picture.
¥ With Auto Sequence Mode, each channel can be viewed sequentially.
¥ Date, Time, and Alarm Display Functions can be reset.
SDM-090(P)A 6/26/01 5:46 PM Page 1-2
1-2
Digital Multiplexer SDM-090(P)
¥ For remote control, RS-232C Cable can be connected to PC.
¥ This unit can be powered from 100 to 240V AC.
¥ When Alarm Signal was input, the CHANNEL number, which indicates
ALARM, is displayed with warning sound. Besides, if more than two ALARM
signals occur simultaneously, you will have Multi Mode with which several
channels can be monitored at the same time.
Such ALARM information is recorded in ALARM LIST.
¥ With the Channel Loss Detection function, if Channel Loss occurs, the
CHANNEL number, which indicates LOSS, is displayed. Such CHANNEL
LOSS information is recorded in “ALARM/LOSS LIST.”
SDM-090(P)A 6/26/01 5:46 PM Page 1-2
1-3
Digital Multiplexer SDM-090(P)
Name of parts and Function
FRONT PANEL
A. POWER SWITCH
Power ON/OFF.
B. MULTI SCREEN DISPLAY
- MULTI SCREEN
You are in the multi-screen mode. Each press of the MULTI SCREEN Button shows the
picture displayed.
- REC CHECK
LIVE MODE: VCR output is displayed on the monitor.
P.B MODE: VCR input is displayed on the monitor.
This mode flashes during REC CHECK operation.
- LIVE/P. B.
Button for selecting either LIVE MODE or Playback MODE. LIVE MODE will be
flashed.
- TRIPLEX
Button for selecting TRIPLEX MODE. Flashes during TRIPLEX operation.
- PIP
Button for selecting PICTURE-IN-PICTURE.
C. CAMERA SELECT
Button for selecting proper CHANNEL.
A
B
C
D EF
12345678
9
SDM-090(P)A 6/26/01 5:46 PM Page 1-3
1-4
Digital Multiplexer SDM-090(P)
D. ALARM
- RESET/ERASE
Button for deactivating ALARM. When ALARM is input, RESET/ERASE Button
should illuminate.
When “ALARM/LOSS LIST” is displayed on the screen, pressing this Button will
erase page by page.
- LIST
Shows ALARM/LOSS LIST.
E. SETUP/FUNCTION
- MENU
Pressing this Button will make LED lit, and MAIN MENU appears on the screen.
- ENTER
Used when switching from MAIN MENU to SUB MENU.
- SET
This function is used when moving from SUB MENU to MAIN MENU after setting
programs on each MENU screen, or is used when setting each channel for multi-
screen. When setting channels for multi-screen, the channel number flashes.
- SEQUENCE
When pressing this Button, each Channel will automatically be switched to the next
channel sequentially with some time intervals, and LED should illuminate. Pressing
again will stop illuminating, and stops sequencing.
- FREEZE
When pressing this Button, selected screen becomes still, and LED should
illuminate.
- ZOOM
When pressing this Button, the screen should enlarge. Pressing once enlarges
twice, and another pressing enlarges 4 times, and pressing once again will bring the
screen back to normal.
F. MOVE ( , , , )
This function is used when setting Program Menu, Channel of Multi-screen, and
Zoom Mode, and also when moving Cursor.
SDM-090(P)A 6/26/01 5:46 PM Page 1-4
1-5
Digital Multiplexer SDM-090(P)
REAR PANEL
A. CAMERA INPUT / LOOP THROUGH OUT (IN/OUT)
Up to 9 camera signals can be input. When transmitting camera signals to external
devices, OUT terminal can be used.
B. ALARM IN / ALARM OUT / VTI TERMINAL
- VTI: TRIGGER Output Connection terminal of VCR
- ALARM IN: Up to 9 ALARM Sensors can be connected. “G” indicates grounding
terminal connected to ALARM Input, and should be connected to grounding terminal
of sensors.
- ALARM OUT (HOT/COLD): When ALARM is activated, ACTIVE MAKE Signal is
generated.
- ALARM RESET : Connected to RESET terminal of VCR, and when ALARM is
deactivated, PULSE is generated.
F
I
B
E
D
G
H
A
C
VCR
VCR
SP0T
MAIN
MON
MON
RS-232C
1 2 3 4 5
6789
123456789
~AC IN
IN
OUT
IN
OUT
HOT
A/O
A/R VTI
COLD
CAMERA
G
SDM-090(P)A 6/26/01 5:46 PM Page 1-5
1-6
Digital Multiplexer SDM-090(P)
C. VCR IN/OUT (BNC)
Indicates terminal for connecting to VCR Input/Output.
D. MONITOR OUT (BNC)
Indicates terminal for connecting to Monitor’s video Input terminal.
E. SPOT OUT (BNC)
Indicates terminal for connecting to Monitor’s video Input terminal.
F. VCR IN/OUT (4PIN MINI DIN)
Indicates terminal for connecting to VCR’s S-VHS Input/Output terminal.
G. MONITOR OUT (4PIN MINI DIN)
Indicates terminal for connecting to Monitor’s video S-VHS Input terminal.
H. RS-232C
With RS-232C cable, Remote Control can be done.
I. ~AC IN
Connects to Power Cord.
SDM-090(P)A 6/26/01 5:46 PM Page 1-6
CHAPTER 2
Installation
SDM-090(P)A 6/26/01 5:46 PM Page 1-7
Digital Multiplexer SDM-090(P)
2-1
CHAPTER 2. INSTALLATION
Preparing for the Installation
The following information is prepared for safe installation of the unit.
This unit can be placed on a flat table or installed in the rack. It should not be
used vertically or skew, but horizontally. The location of the unit and the
composition of wiring are very important in properly operating the system. When
equipment is placed too close or if ventilation is not properly done, system may
not work properly, and maintenance of the system may be difficult. In order to
prevent system failure and to reduce system shut-down by outside
environmental factors, air circulation in the system operating room, and the
cover of the unit must be fixed. Do not open the cover voluntarily because high
voltage within the unit may cause electric shock.
PHYSICAL & ENVIRONMENTAL
¥ Operating Temperature : 0 °C to 40 °C
¥ Maintenance Temperature : -20 °C to 60 °C
¥ Operating Humidity : 20% to 85% (RH)
¥ Maintenance Humidity : 20% to 95% (RH)
¥ Power Supply : 100 ~ 240 VAC
¥ Power Consumption : less than 13W
¥ Frequency : 50/60 Hz
CAUTIONS
When system is operated, input voltage range must be within 10% of nominal
voltage, and power consent should be grounded. Heating devices such as hair
dryer, iron, refrigerator should not be used together. For safe power supply, AVR
(Automatic Voltage Regulator) is recommended.
The connector linked to this equipment can affect EMI,so it is recommended to
coil the CORE-FERRITE for use.
SDM-090(P)A 6/26/01 5:46 PM Page 2-1
Digital Multiplexer SDM-090(P)
2-2
Precautions when Installing
Precautions when Installing
¥ Be sure to turn the unit off before installing.
¥ Avoid shock or vibration since
they may cause unit malfunction.
¥ Keep away from magnets, radio or TV to
avoid magnetic damage.
¥ During or after installing the unit, be sure to
maintain the area around the unit clean.
SDM-090(P)A 6/26/01 5:46 PM Page 2-2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69

Samsung SDM-090P Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI