READ & SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
Surface Mount Door Camera
Model VSC4S
Use with NuTone Models VSM4SK and VSUC4SK
INSTALLATION INSTRUCTIONS
This booklet contains information for installing the camera.
All system wiring and rough-in frames should be installed
before mounting and wiring the master station. Refer to the
installation instructions packaged with the rough-in frames
for detailed wiring information.
For more detailed information on wiring and mounting other
system components (i.e., optional camera, rough-in.), refer
to the installation instructions packaged with the separate
components.
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS . . . . .2-4
VSM4SK & VSUC4SK WIRING ILLUS. . . . . . . .5
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . .5
Contents of Carton . . . . . . . . . . . . . . . . . . . . . . .5
Precautions and Guidelines . . . . . . . . . . . . . . . .5
Wiring Specifications . . . . . . . . . . . . . . . . . . . . .6
Camera Wiring Precautions . . . . . . . . . . . . . . . .6
Connecting and Mounting the Camera . . . . . .6-7
Operational Checkout . . . . . . . . . . . . . . . . . . . . .7
Camera Volume Adjustment . . . . . . . . . . . . . . .7
Camera Lens Manual Adjustment . . . . . . . . . . .7
FCC INFORMATION PART 15 RULES . . . . . . . .8
WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TO REGISTER THIS PRODUCT, VISIT WWW.NUTONE.COM
2
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of
uninstalled “dangerous voltage” within the product’s enclosure. This voltage may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution
CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING
OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE PLACE ON THE APPARATUS.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult and
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Unplug the apparatus during lighting storms or when
unused for long period of time.
13) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fall
-
en into apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally
, or has been
dropped.
IMPORTANT SAFETY INSTRUCTIONS
PRECAUTIONS
SAFETY
Should any liquid or solid object fall into the cabinet, unplug
the unit and have it checked by the qualified personnel
before operating it any futher.
Unplug the unit from the wall outlet if it is not going to be
used for several days or more. To disconnect the cord, pull it
out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat build-
up. Do not place the unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that may block the
ventilation holes.
INSTALLATION
Do not install the unit in an extremely hot or humid place or
in a place subject to excessive dust or mechanical vibration.
The unit is not designed to be waterproof
CLEANING
Clean the unit with a dry soft cloth. Never use strong
solvents such as thinner or benzine as they might damage
the finish of the unit.
1
. READ THESE INSTRUCTIONS
—
All the safety and
operating instructions should be read before the product
i
s operated.
2. RETAIN INSTRUCTIONS — The safety and operating
instructions should be retained for future reference.
3. HEED ALL WARNINGS — All warning on the product
and in the operating instructions should be adhered to.
4. FOLLOW ALL INSTRUCTIONS — All operating and use
instructions should be followed.
5. CLEANING — Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol.
Use a dry cloth for cleaning.
6. ATTACHMENTS — Do not use attachments not recom-
mended by the product manufacturer, as they may cause
hazards.
7. WATER AND MOISTURE — Do not use this product
near water—for example, near a bath tub, wash bowl,
kitchen sink, laundry tub, in a wet basement, near a
swimming pool, and the like.
8. ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod bracket, or table. The product
may fail, causing serious injury to a child or adult, and
serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the man-
ufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by the
manufacturer.
9. VENTILATION — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the product.
They protect it from overheating, and these openings
must not be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in built-in installation such as a bookcase or
rack unless proper ventilation is provided, or the manufac-
turer,s instructions have been adhered to.
10. POWER SOURCES — This product should be operated
only from the type of power source indicated on the mark-
ing label. If you are not sure of the type of power supply
in your home, consult your product dealer or local power
company. For products intended for operation from bat-
tery power or other sources, refer to operating instruc-
tions.
11. GROUNDING OR POLARIZATION — This product may
be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other).
This plug
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug still cannot be
inserted, contact your electrician to replace you obsolete
o
utlet. Do not defeat the safety purpose of the polarized
plug.
12. POWER-CORD PROTECTION — Power-supply cords
should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them pay-
i
ng particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the prod-
uct.
13. OUTDOOR ANTENNA GROUNDING — If an outside
antenna or cable system is connected to the product, be
sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-
up static charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes, an
requirements for the grounding electrode (Refer to the fig-
ure on page 4).
14. LIGHTNING — For added protection of the product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and
power-line surges.
15. POWER LINES — An outside antenna system should not
be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits.
16. OVERLOADING — Do not overload wall outlets, exten-
sion cords, or integral convenience receptacles, as this
can result in a risk of fire or electric shock.
17. OBJECT AND LIQUID ENTRY — Never push objects of
any kind into the product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the product.
18. SERVICING — Do not attempt to service this product
yourself as opening or removing covers my expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personal.
19. DAMAGE REQUIRING SERVICE — Unplug this product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions.
A. When the power-supply cord or plug is damaged.
B.
If liquid has been spilled, or objects have fallen into the
product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following
IMPORTANT SAFETY INSTRUCTIONS
3
t
he operation instructions. Adjust only those controls
that are covered by the operating instruction, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
o
peration.
E. If the product has been dropped or damaged in any
way.
F
. When the product exhibits a distinct change in perform-
ance — this indicates a need for service.
20. REPLACEMENTS PARTS — When replacement parts
are required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the sam characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
2
1. SAFETY CHECK
—
Upon completion of any service or
repairs to this product, ask the service technician to per-
form safety checks to determine that the product is in
proper operating condition.
22. WALL OR CEILING MOUNTING — The product should
b
e mounted to a wall or ceiling only as recommended by
the manufacturer.
23. HEAT — The product should be situated away from heat
s
ources such as radiators, heat resistors, or other prod-
ucts (including amplifiers) that produce heat.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUNDING CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ELECTRIC
SER
VICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
4
VSM4SK AND VSUC4SK VIDEO DOOR ANSWERING
REPRESENTATIVE WIRING ILLUSTRATION
INSTALLATION
CONTENTS OF CARTON
Check (_) for following VSC4S carton contents:
¨ VSC4S Door Camera with mounting frame and
rubber gasket
¨ Hardware bag assembly containing:
(2) #6 x 1 1/4" screws
(2) #6 x 3/4" machine screws
(1) 4mm camera attachment screw
¨ Installation Instructions
VSM4SK
VSUC4SK
5
Note to Installer: Do not discard these instal-
lation instructions. Please give all installation
instructions, warranty registration and home-
owner’s manual to homeowner.
PRECAUTIONS AND GUIDELINES
The NuTone VSC4S door camera has been designed to
work with NuTone models VSM4SK or VSUC4SK.
Please read and follow ALL installation instructions,
guidelines and precautions. Any deviation from these
instructions or miswiring combinations will cause the
unit to fail and all NuTone warranties will be void.
Following are the installation instructions for the VSC4S
Camera. Please refer to the installation instructions
and homeowners manual packed with the VSM4SK
or VSUC4SK when installation and operating these
models.
WARNING: 120 Volt AC power to the VSM4SK
rough-in and VSUC4SK monitor must remain
off until all system wiring and product mount-
ing at the monitor and camera is complete.
•
Observe all local regulations and codes in your area.
•
All screw terminals at the camera, VSM4SK or
VSUC4SK must be secure.
• Observe all color codes of wires when connecting cam-
era to VSM4SK or VSUC4SK.
• The VSC4S is designed to be used with category 5, or
category 6 cable (purchased separately). The use of
cable other than category 5, or category 6 cable will
void all NuTone warranties and may result in faulty
installation and improper operation.
• The door camera must not be mounted in an area
that would be subject to direct sunlight or a strong
reflection from the sun.
Wiring Specifications
T
he VSC4S is designed to connect to the VSM4SK, or
VSUC4SK video door answering system using category 5 or
category 6 cable.
• Maximum cable length: 250 ft
IMPORTANT: NuTone cannot be responsible for
improper system operation that results from inter-
ference generated by light dimmers, fluorescent
lighting fixtures, and similar electrical products.
Such interference must be corrected at the source.
TO HELP REDUCE THIS INTERFERENCE, ALL
WIRING CONNECTED TO THE CAMERA MUST BE
PLACED AT LEAST 12 INCHES FROM ANY A.C.
POWER WIRING. AVOID RUNNING INTERCOM
WIRES PARALLEL TO A.C. POWER WIRING.
Connecting and Mounting the Camera
Frame Construction (New Construction)
1.At the camera location, attach a single gang wall box (pur-
chase locally) to the wall stud. Normal mounting height is
60" from the top of the wall box to the floor.
2.Run the category 5 or category 6 cable from the VSM4SK
or VSUC4SK location to the camera location (250 ft maxi-
mum length).
3.Run the cable into the box. Leave approx 12" of extra
cable in the box.
4.After the finished wall surface has been applied, strip
approximately 2" of outer protective jacket from the catego-
ry 5, or category 6 cable.
5.Separate and strip approx 1/2" of insulation
from each of the eight wires in the cable.
Twist the following cables together:
• OR and OR/WH
• GR and GR/WH
• BL and BL/WH
• BR and BR/WH
6.Remove the plastic back frame and rubber gasket from the
camera. Position the back frame and gasket over wire and
attach to the wall box using (2) #6 x 3/4" machine screws
(supplied). Level the back frame before tightening screws
completely.
7.Attach each of the twisted pair of wires to
the corresponding screw terminal on the
back of the camera.
T
ighten each screw
securely.
8.Dress extra cable into wall box and position
the camera, starting at the top onto the
plastic back frame.
9
.Fully seat the camera into the back frame
and secure the camera with 4mm camera
attachment screw (supplied) thru the bottom
of the back frame and camera.
I
mportant: If camera is exposed to
o
utside elements, caulk should be
added to the top and sides of the
camera at the wall surface. Do not
caulk bottom surface.
Existing Construction
1a. At the camera location, a single gang wall box can be
cut into the existing wall surface (maybe required by
local code). Normal height is 58" from center of the hole
to the floor.
1b. At the camera location, drill a 3/8" hole
into the wall directly next to a wall stud.
Normal mounting height is 58" from the
center of the hole to the floor.
2.Run the category 5 or category 6 cable from
the VSM4SK or VSUC4SK location to the
camera location (250 ft maximum length).
3.Run the cable thru the hole (or into the box
if used). Leave approx 12" of extra cable
protruding thru the hole (or box if used).
4.Strip approx. 2" of outer protective jacket
from the category 5, or category 6 cable.
5.Separate and strip approx 1/2" of insulation
from each of the eight wires in the cable.
Twist the following cables
together:
• OR and OR/WH
• GR and GR/WH
• BL
and BL/WH
• BR and BR/WH
6.Remove the plastic back frame and rubber
gasket from the camera. Position the back
frame and gasket over wire and attach into
the wall stud using (2) #6 x 1 1/4" screws
(supplied) (or two # 6-32 x 3/4" machine
screws (supplied) if a wall box was used).
Level the back frame before tightening
screws completely.
7.Attach each of the twisted pair of wires to
the corresponding screw terminal on the
back of the camera. Tighten each
screw securely.
6
7
8
.Dress extra cable into the hole
(or wall box if used) and position the
camera, starting at the top onto the
plastic back frame.
9
.Fully seat the camera into the back
f
rame and secure the camera with 4mm
camera attachment screw (supplied)
thru the
bottom of the back frame and camera.
Important: If camera is exposed to
outside elements, caulk should be
added to the top and sides of the
camera at the wall surface. Do not
caulk bottom surface.
Operational Checkout
Refer to the instructions provided with NuTone models
VSM4SK, or VSUC4SK.
Camera Volume Adjustment
The VSC4S door camera is provided with a volume level
adjustment set screw. The adjustment has been pre-set at
the factory to provide the optimal volume level at the door
camera. The volume level can be adjusted if your specific
application requires the level to be either increased or
decreased. Insert a jeweler’s screwdriver into the small hole
that is shown in the camera illustration. Rotate the small set
screw to adjust the volume level.
Important: Do not use excessive force to rotate the screw.
Damage could occur to the camera, and loss of audio may
result. Use extreme caution when making the adjustment. Do
not use a screwdriver that is too big for the application.
VSC4S
Volume Adjustment
Camera Lens Manual Adjustment
T
he VSC4S door camera is provided with a manual camera
lens adjustment. The adjustment can be used to fine tune
the angle of the camera lens to compensate for installations
that are not directly in line to the viewing area. The adjust-
ment is located on the back of the camera, as shown in the
camera illustration. Move the adjustment control upward to
lower the camera lens. Move the adjustment control down-
w
ard to raise the camera lens. Adjust the camera lens posi-
tion to provide the best viewing area for your installation.
VSC4S
Lens Adjustment
FCC Information Part 15 Rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause
h
armful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning – This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the
authority to operate this equipment if an unauthorized change or modification is made.
FCC Warning – Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
The serial number of this product may be found on the rear side of the product. No others have the same serial numbers as yours.
You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid
identification in case of theft.
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in Korea, 05/2006, Part No. 100915
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: NuTone VSC4S Manuel utilisateur
Related papers
-
NuTone VSUC4SK Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
nvent BOX-NS22N Operating instructions
-
Panasonic BY-HPE11KTA Safety Instructions
-
Acome Izilink GIGA Installation guide
-
Sony VCT-MP1 Operating instructions
-
Swann SWIFI-FLOCAM2W Quick start guide
-
Swann SOWHDFLOCAMW2PK User manual
-
Samsung SCC-B5392P User manual
-
-
JVC TK-C920BE Operating instructions
-
