Posiflex KP-200 / KP-210 User manual

Brand: Posiflex

Model: KP-200 / KP-210

Type: User manual

This manual is also suitable for

KP-200

Part 1

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions manual, may cause interference

to radio communications. It has been tested and found to comply with limits for a Class

A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to

provide reasonable protection against interference when operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause

interference in which case the user at his own expense will be required to take whatever

measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized

technicians opens the machine. The user should consult his/her dealer for the problem

happened. Warranty voids if the user does not follow the instructions in application of

this merchandise. The manufacturer is by no means responsible for any damage or

hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,

Posiflex will assume no liability for any technical inaccuracies or editorial or other

errors or omissions contained herein, nor for direct, indirect, incidental, consequential

or otherwise damages, including without limitation loss of data or profits, resulting

from the furnishing, performance, or use of this material.

This information is provided “as is” and Posiflex Inc. expressly disclaims any

warranties, expressed, implied or statutory, including without limitation implied

warranties of merchantability or fitness for particular purpose, good title and against

infringement.

The information in this manual contains only essential hardware concerns for general

user and is subject to change without notice. Posiflex reserves the right to alter product

designs, layouts or drivers without notification. The system integrator shall provide

applicative notices and arrangement for special options utilizing this product. The user

may find the most up to date information of the hardware from web sites:

http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage

peripheral. Posiflex will not be responsible for any loss of data resulting from the use,

disuse or misuse of this or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced,

stored in a retrieval system, or transmitted in any form or by any means, electronic,

mechanical, photocopying, or otherwise, without prior express written consent from

Posiflex Inc. the publisher of this documentation.

All brand and product names and trademarks are the property of their respective holders.

/ KP

210

SIDE MOUNT

PROGRAMMABLE KEYPAD

USER’S MANUAL

Rev.: Original

P/N: 19810900010

Part 2

GENERAL DESCRIPTION

OVERVIEW

Table below indicates construction of this series of security devices.

KP-200 KP-210

Structure

Upgrade kit for HT

series

Upgrade kit for

TM/LM-7112 series

Programmable keypad

Vertical layout

Magnetic stripe reader

Optional

Smart card reader Optional

OPTIONS

Items underlined below means that this item must be installed by Posiflex

authorized distributor only and never by average user. Items in Italic printing

below means that this item must be installed prior to delivery from the factory.

• Magnetic Stripe Reader (PS2 KB interface)

∗ ISO 7811 head reader for tracks 1 and 2

∗ ISO 7811 reader head for tracks 2 and 3

∗ ISO 7811 reader head for tracks 1, 2 and 3 + AAMVA + CA DMV

∗ JIS/II reader head

• Smart card reader

• Case color selection between ivory and charcoal

Note: if there is no smart card reader option installed with the keypad, there

will be no USB interface and cable installed.

Part 3

INSTALLATION GUIDE

UNPACKING CONTENTS

Items packed in for Qt’y

The side mount programmable keypad itself 1

Fixation screws with washers to hold KP to HT or TM/LM 2

Transparent key caps for single key 20

Key clip 1

Control keys (4 pcs / set) 1

Legend sheets (4 sh. / set) 1

This manual 1

Note: Utility drivers for KP-200 / KP-210 can be found in the CD ROM

packed together with the Posiflex HT series POS terminal system or

monitor TM-7112 or LM-7112 that this upgrade kit is to be installed to.

Or please find for latest updates by visiting driver download page of our

web site: http://www.posiflex.com.tw/DriversDownload.asp

MECHANICAL FIXATION

Either the KP-200 to be installed in the HT series host system or the

KP-210 to be installed to the stand-alone touch/LCD monitor TM/LM-7112,

the upgrade kit is installed to the right edge of the

LCD panel. Use the 2 fixation screws that come

along with KP-200 or KP-210 to hold the keypad

unit to the LCD panel from its back as circled in the

left picture. Connect the PS/2 cable of KP-200 to

the PS/2 KB port in connection area inside the back cover of HT system.

Connect the much longer PS/2 cable of KP-210 to the PS/2 KB port of the host

system that the TM/LM-7112 is connected to.

For the smart card reader option in the keypad, there will be an USB

cable coming from bottom of the keypad. Please hold

it to the holder on back of the LCD panel as arrowed

in the above picture and connect it

to the extended USB port of HT

system or to a downlink USB port

in TM/LM-7112 monitor. Find the

downlink USB port of TM/LM-

7112 is at right side of its base unit

as in the left picture. Find the top

side cable cover of HT series as in the upper right

picture and gently press it down and slide aside to open it and connect the USB

Cable Exit

Cable Cover

Downlink

USB Ports

Extended USB Port

Part 4

cable of KP-200 to the extension USB port as shown in the lower right picture

in last page.

EXTENDED PS/2 KEYBPARD CONNECTION

Refer to the right picture on back

of KP-200 / KP-210 with a partially

enlarged picture at inclined angle. In the

cavity found at lower rear side of KP-200 /

KP-210, there is a PS/2 KB jack. Connect

a standard PS/2 keyboard device to this

jack and insert the cable from the PS/2

keyboard device into the cable pass for

strain relief and fixation when an extended

PS/2 KB is required.

KEYTOP LAYOUT

Keytop Replacement

The keypad in KP-200 / KP-210 is organized into 2 parts: a 4 by 4

numerical keypad area and a 4 by 6 matrix minus a 2 by 2 square recess

programmable keypad area. However, this keypad allows some layout

alterations by the system integrator. Besides the standard single key installed,

there are double keys and blank keys for purchase to provide more convenient

interface with the user.

When replacement of keytop is required, it is advisable to use a

flattop (minus sign) screw driver (Do not use the attached key clip for this

operation.) to help getting the key top off gently. Please always first orientate

the key tops as below before inserting any keytop into the case of the keypad.

Failure to do so could result in permanent damage not covered in product

warranty. Please always match the latching tab on bottom stem of keytop with

the tab in guiding hole and gently press the key top down till a click sound is

heard as indicated in the pictures below.

Single key top

Latching tab

Double key top

Tab in the

guide hole

KP-200 / KP-210

Rear View

Cable

Pass

KB Jack

Part 5

Labeling On Keytop

The programmable keypad is provided with an easy and durable

method for reminding the user of content programmed in each programmable

key. First preprint (or write) in each cell of the attached colored legend sheet

the “name” for each key. Stick each cell to the corresponding keytop and then

put on the transparent key cap from the accessories. In this way, the labeling

will be protected and resistant to scratch or rubbing.

When re-labeling is required, please use the attached key clip to hook

up the transparent key cap and change the label then re-cap.

KEYPAD PROGRAMMING

The programming of the keys above the numerical keypad in KP-200

or KP-210 is in general the task of the system integrator and not the average

end user. For end user, please go to the chapter of “OPERATION GUIDE” of

this manual directly.

Utility Installation

In the Posiflex Product Information CD attached with Posiflex POS

terminal, there is a subfolder named as “\Drivers\KP”. If there is only a

subfolder like “\Drivers\KP100” but not “\Drivers\KP”, please download from

our web site: http://www.posiflex.com.tw/DriversDownload.asp the keypad

programming utility for KP-200 / KP-210.

In the above mentioned subfolder there are 2 further subfolders

“KBM40.xxx” and “KBW40.xxx” with “xxx” representing any number of the

utility revision. For operating system of MS-DOS or Win98 DOS box, please

execute “KBM40.xxx\INSTALL.EXE” to install the utilities “KBM.EXE” and

“RWM.EXE”. The “KBM.EXE” is a key-by-key programming utility for DOS

environment. The “RWM.EXE” is a special direct transfer utility under DOS.

Execute “KBW40.xxx\SETUP.EXE” to install the programming utility

“KBW.EXE” for various editions of Windows OS. After completion of the

“Setup”, there will be a program group “Posiflex Tools” in the program files.

Clicking the program “Posiflex Programmable Keyboard” in this group will

activate the KBW.EXE for KP-200 / KP-210. Please select the right model

when entering the program.

Programming Preparation

A normal keyboard may be required for inputting data in keypad

programming. If a PS/2 interface keyboard is to be used, please connect it to

the extended PS/2 KB jack in the recessed cavity on back of KP-200 / KP-210

as mentioned earlier. Please note that there must not be any other PS/2 device

connected in between the KP-210 and the PS/2 KB port of the host system in

the keypad programming operation.

Part 6

Quick Reference Guide for Keypad Programming

Please refer to our web site for every detail in programming the

programmable keyboards or keypads. The following simplified guide severs as

a concise tool for instant application.

Keys To Program How to Program Them

Esc, F1 - F12, Back Space, Shift,

Ctrl, Alt, Insert, Delete, End, Page

Up, Page Down, Print Scrn, Scroll

Lock, Break, and all Arrow

Functions

Press: (Alt-N), Esc, “Desired Key”,

Down Arrow

A - Z, 0 - 9, ~ ` ! @ # $ % ^ & * ( )

- _ = + } { [ ] | \ ’ ; ” : /. , < > ?

Press: Enter, “Desired Key or

Keys”, Down Arrow

Tab, Enter

Press: (Alt-N), “Desired Key”,

Down Arrow

Caps Lock Press: Enter, (Alt-C), Down Arrow

Multi-shift

Press: (Alt-N), (Alt-M), Down

Arrow - - - - Press (Alt-M) as many

times as needed.

Separator In Between Any Text, Press (Alt-S)

Hardware Limitation in Programming

In case of “multiple combination key” application which means

pressing three or more keys at the same time to obtain certain data output from

the keyboard, there could be some limitations inherent from the nature of

keyboard structure. The CPU of keyboard detects the contact between the

“horizontal” and “vertical” lines for each key press, recognizes which key is

pressed and sends correspondent data to the host computer. When there are

many keys pressed at the same time, and the pattern of the contacts coincides

with some special relationship, there are chances that the CPU of keyboard be

confused about exactly which keys are pressed. The user may change the

locations of the key-definition to prevent this once such confusion happens.

MSR CONFIGURATION

Please find the subfolder “\Drivers\KP\MSR” in the Posiflex Product

Information CD or download from our web as mentioned earlier and go to

either the subfolder “DOS” for the MSR manager under MS-DOS or the other

subfolder “Win” for setting up the MSR manager under Windows OS. The

MSR manager can control parameters like individual track enable/disable,

Alt+Num emulation and Start/end sentinel substitute.

Part 7

SMART CARD READER DRIVER INSTALLATION

This driver should be installed in the system prior to the system

detection of the new hardware. Therefore, the USB connection of KP-200 /

KP-210 could have to be disconnected before driver installation and then

connect it back afterwards. Please find the subfolder “\Drivers\KP\SC200” in

the Posiflex Product Information CD or download from our web as mentioned

earlier. Execute the “SETUP.EXE” to install the driver into the Windows OS.

The reader is PC/SC 1.0 compliant. The reader is also EMV level 1 compliant.

The smart card reader is also supported by Microsoft CCID generic class

driver.

Part 8

OPERATION GUIDE

KEYPAD LAYOUT

1. 6 position lock switch for electronic control key

2. Multi-page programmable keys (Note: The white keys in dark

color keypad in the example picture is for illustration purpose

only. In normal product, they will be of same tone.)

3. Numerical keypad

4. MSR slot

5. MSR mark

6. Smart card reader slot

7. Smart card reader mark

8. Example smart card to be read

PROGRAMMABLE KEYPAD

Electronic Control Key

On top right corner of KP-200 / KP-210, there is an electronic control

key that can be turned to one of the following 6 positions: LP, L0, L1, L2, L3

and L4. It can only be taken out from the switch at positions L0 and L1. The

purpose of this electronic key serves 3 folds: When the key is switched to (and

extracted from) position L0, the whole keypad output (including the optional

MSR but excluding the optional smart card reader) will be blocked off by

hardware to work as a security measure. A programmable answer back code

for the final position of the 6 position electronic key will be sent by the keypad

to the host computer whenever the key is switched to a new position for a

programmable delay time or when the host computer sends a specific code

(E7h) to inquire the keypad. The position of the electronic key determines

which page of the key content table for the 20 push keys applies, while the

definitions of the same key within different pages can be programmed so

absolutely independent to provide instant menu change over.

Front View

Front Right Side View

Part 9

This electronic key switch is delivered with a set of 4 pcs of keys,

each marked as “PRG”, “REG”, “Z” and “GT”. The effective range of each of

the 4 keys can be illustrated by the following table and drawing.

PRG REG Z GT

LP Y N N N

L0 Y Y Y Y

L1 Y Y Y Y

L2 Y Y Y Y

L3 Y N Y Y

L4 N N N Y

Programmable Keys

The multi-page programmable keys can deliver to the host system the

string of keyboard input as programmed. Please note that when the 6 position

electronic control key is turned to a different position, the content of same key

could be completely different. It is also possible to use combination keys if

programmed to. There will be no output of these keys if the control key is

turned to “L0” position.

Numerical Keypad

The numerical keypad is durably pre-marked. When the 6 position

electronic control key is turned to a different position, the content of same key

remains unless it has been programmed in a particular way. The numerical

keypad is not applicable in combination keys. There will be no output of these

keys if the control key is turned to “L0” position.

MAGNETIC STRIPE READER

For magnetic stripe card reading, be sure to insert the card to the

bottom with magnetic stripe facing the mark aside the slot. The movement of

the card can be either inserting the card from the top surface then sliding the

card down out of the slot, or sliding the card upward from the lower side of the

slot till it reaches the top end as long as the card is a standard one. A non-

standard card recorded without complete degaussing prior to recovery may

accept only one direction in card reading.

The magnetic stripe reader in KP-200 / KP-210 connects to the host

through KB port and therefore requires no driver installation to get it working.

However, when the control key is turned to “L0” position, the output of any

MSR reading is blocked for security concern.

Part 10

SMART CARD READER

Card Insertion

For smart card reading, please insert the end of the smart chip first

and have the chip facing the mark aside the side slot of KP-200 / KP-210 as in

the example picture in front side view.

Applicable Smart Card Type

The smart card reader can be used for both asynchronous and

synchronous type smart cards. For asynchronous type smart card, it reads the

card with T = 0 and T = 1 protocols up to 340 Kbps of EMV and ISO modes.

For synchronous type smart card, coverage includes: 2-wire (SLE4432/42), 3-

wire (SLE4418/28) etc., SDA/I2C, 4403, 4433, 4404, 896

T31454

Posiflex KP-200 / KP-210 User manual

Brand: Posiflex

Model: KP-200 / KP-210

Type: User manual

This manual is also suitable for

KP-200

Download PDF

report

Posiflex KP-200 / KP-210 User manual

This manual is also suitable for

Posiflex KP-200 / KP-210 User manual

Related papers

Other documents