For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800-633-5096
service@seidal.com
www.seidal.com
MS998700TX
Kendleton TV/ Media Console
ASSEMBLY INSTRUCTION
PO#：
A.
Quantity
of 1
top panel
B.
Quantity
of 1
fixed shelf panel
C.
Quantity
of 1
left side panel
D.
Quantity
of 1
vertical panel
E.
Quantity
of 1
right side panel
F.
Quantity
of 1
bottom panel
G.
Quantity
of 1
top rail
H.
Quantity
of 1
back panel left
I.
Quantity
of 1
back panel right
J.
Quantity
of 1
adjustable shelf
K.
Quantity
of 1
drawer front panel
L.
Quantity
of 1
left drawer side panel
M.
Quantity
of 1
right drawer side panel
N.
Quantity
of 1
drawer back panel
O.
Quantity
of 1
drawer bottom panel
P
Quantity
of 2
l
eg
Q
Quantity
of 1
top support
R
Quantity
of 1
Middle leg
S
Quantity
of 1
Cross bar
MS998700TX Kendleton TV/Media Console
Parts list
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
diagrams below. You may receive extra hardware with your unit.
P
age 2
1.
Q
uantity
of 2
Ball bearing slide
2.
Quantity
of 12
Cam bolt
3.
Quantity
of 12
Cam lock
4.
Quantity
of 18
Wood Dowel
Dia5/16”x1-3/16”L
5.
Quantity
of 12
Bolt :Dia1/4”x5/8”L
6.
Quantity
of 4
Bolt: Dia. 1/4”x1-1/2”L
7.
Q
uantity
of 6
Bolt
Dia1/4”x1-5/8”
8.
Quantity
of 7
Screw
Dia3/16”x1-1/4”L
9.
Quantity
of 12
Screw
Dia3/16”x1/2”L
10.
Quantity
of 8
Screw Dia.1/8”x3/4”L
11.
Quantity
of 1
handle
12.
Quantity
of 2
Small bolt
13.
Quantity
of 5
leveler
14.
Quantity
of 1
Allen wrench
15.
Quantity
of 12
COVER
16.
Quantity
of 8
Back holder
17.
Quantity
of 4
Adjustable pin
18.
Quantity
of 6
Bolt :Dia1/4”x1/2”L
1
9
.
Quantity
of 3
Bolt :Dia1/4”x1-3/16”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For
replacement parts or questions, please
Call Customer Service at 1-800-633-5096
please call Manufacturer for assistance, questions or
Parts.
Assembly Tool Required No.2 Phi
Page 3
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)
Figure 1
Unpack and lay parts on clean,
padded surface like carpet or
blanket. Check that you have all
parts indicated on the front page
Attach ball bearing slide (1) on left
side panel (C) & vertical panel (D)
with screw (9),
Tighten with a Philips screwdriver
(not included)
Figure 2
Insert wood dowel (4) into predrilled
holes on vertical panel (D) and right
side panel (E),
Attach top rail (G) to vertical (D)
and right side panel (E)
MS998700TX Kendleon TV/Media Console
Assembly Instructions
P
age 4
Figure
3
Insert cam lock (3) into predrilled
holes on pre-assembled unit in
figure 2.
Screw cam bolt (2) into pre-drilled
holes on top panel (A). Attach top
panel (A) to pre-assembled unit in
figure 2 by inserting wood dowel (4)
& cam bolt (2) into corresponding
pre-drilled holes until top panel (A)
& pre-assembled unit in figure 2
meet.
Secure by rotating cam lock (3)
clockwise with Phillips screwdriver
Cover the cam lock hole with cover
(15).
Attach top support (Q) to top panel
(A) with bolt (5) .
Tighten bolt with Allen wrench (14)
Figure 4
Attached the top rail (G) to top panel
(A) using screw (8), tighten screw
with Phillips screwdriver (not
included)
Insert cam lock (3) into predrilled
holes on fixed shelf panel (B).
Screw cam bolt (2) into pre-drilled
holes on vertical panel (D). Attach
fixed panel (B) to pre-assembled
unit in figure 2 by inserting wood
dowel (4) & cam bolt (2) into
corresponding pre-
drilled holes until
fixed panel (B) & pre-assembled
unit in figure 3 meet.
Tighten by rotating cam lock (3)
clockwise with Phillips screwdriver
(not included)
Figure 5
Attach fixed shelf panel (B) to top
support (Q) using bolt (6) .
Tighten bolt with Allen wrench (14)
Page 5
Figure 6
Insert cam lock (3) into predrilled
holes on left side panel (C).
Screw cam bolt (2) into pre-drilled
holes on pre-assembled unit in
figure 5. Attach left side panel (C)
to pre-assembled unit in figure 5
by inserting wood dowel (4) &
cam bolt (2) into corresponding
pre-drilled holes until left side
panel (C) & pre-assembled unit in
figure 5 meet.
Tighten by rotating cam lock (3)
clockwise with Phillips
screwdriver.
Cover the cam lock holes with
cover (15).
Figure 7
Insert right back panel (I) ＆ left
back panel (H) into groove on left
side panel (C) and right side
panel right (E) and vertical panel
(D) and top panel (A) and fixed
shelf panel(B).
Attach cross bar(S) to fixed shelf
panel (B) with bolt (14).
Attach cross bar(S) to left side
panel ( C)& vertical panel (D) with
bolt (18). Tighten bolt with allen
wrench (14).
Figure 8
Attach bottom panel (F) to
pre-assembled unit in figure 7
with bolt (7)
Tighten bolt with allen wrench
( 14)
P
age 6
Figure 9
Attach leg (P) to pre-assembled
unit in figure 8 with bolt (5)
Attach middle leg (R) to
pre-assembled unit in figure 8
with bolt (18)
Attach leveler (13) to leg(P)&
middle leg (R ) by hand.
Tighten bolt with Allen wrench
( 14)
Figure 10
Attach right drawer side panel
(M) & left drawer side panel
(L) to drawer back panel(N)
with screw (8),
Tighten screw (8) using a
Philips screwdriver.
Figure 11
Slide drawer bottom panel
(O) into the groove of right
drawer side panel (M) and left
drawer side panel (L) and
drawer back panel(N).
Page 7
Figure 12
Insert cam lock (3) into predrilled
holes on pre-assembled unit in
figure 11.
Screw cam bolt (2) into pre-drilled
holes on drawer front panel (K).
Attach drawer front panel (K) to
pre-assembled unit in figure 11 by
inserting cam bolt (2) into
corresponding pre-drilled holes
until drawer front panel (K) &
pre-assembled unit in figure 11
meet.
Tighten by rotating cam lock (3)
clockwise with Phillips
screwdriver (not included)
Cover the cam lock holes with
cover (15).
Use bolt (12) to connect
handle(11) to drawer front
panel(K)
Figure 13
Screw adjustable pin (17) into
right side panel (E) and
vertical panel (D)
Slide in the adjustable shelf
(J) from outside.
P
age
8
Figure 14
Attach back holder (16) to
pre-assembled unit in figure
13 using screw (10) and
tighten using Philips
screwdriver.
Figure 15
Attach the ball bearing slide
(1) on left drawer side panel
(L) and right drawer side
panel (M) with screw (9),
Tighten screw by using Philips
screwdriver.
Figure 16
Now your media console is
ready to use
Page 9
Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s).
If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
service@seidal.com
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
CAUTION
The top shelf is intended for a flat screen television with a maximum overall width of 40” and
supports up to 80 lb.
The top shelf is NOT INTENDED for tube televisions.
Each shelf and drawer should not be loaded with more than 20 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum sizes and weights indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on back panel.
Do not allow children under 16 years to move the cart.
Model: MS998700TX
Kendleton TV/Media Console
Southern Enterprises, Inc
600 Freeport Parkway,
Suite 200 Coppell, Texas, 75019
Manufacture Date: 19/12/2013
/
