For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800-633-5096
service@seidal.com
www.seidal.com
HZ108200TX
Colorblock 2-Drawer
Anywhere Storage Cabinet -
Linen
Assembly Instructions
PO#：
Page 1
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Back Rail
F.
Quantity
of 1
Front Middle Rail
G.
Quantity
of 1
Top Rail
H.
Quantity
of 1
Back Panel
I.
Quantity
of 1
Top Drawer Front
J.
Quantity
of 1
Bottom Drawer Front
K.
Quantity
of 2
Drawer Side Left
L.
Quantity
of 2
Drawer Side Right
M.
Quantity
of 2
Drawer Back
N.
Quantity
of 2
Drawer Bottom
O.
Quantity
of 2
Drawer Bottom Rail
P
Quantity
of 4
Leg
1
Quantity
of 20
Wood Dowel
Dia5/16”x1-3/16”L
2
Quantity
of 20
Cam Bolt
Colorblock 2-Drawer Anywhere Storage Cabinet - Linen
Parts list
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study the
diagrams below. You may receive extra hardware with your unit.
Page 2
3
.
Quantity
of 20
Cam Lock
4
.
Quantity
of 16
Bolt Dia5/16”X1”L
5
.
Quantity
of 2
Knob
6
.
Quantity
of 2
Small Bolt
7
.
Quantity
of 16
Screw Dia1/8”x1”L
8
.
Quantity
of 24
Screw Dia1/8”x1/2”L
9
.
Quantity
of 16
Screw Dia1/8”x1/2”L
10
.
Quantity
of 1
Allen Wrench
11
.
Quantity
of 2
Bracket
12
.
Quantity
of 1
Chain
13
.
Quantity
of 2
Anchor
14
.
Quantity
of 2
Screw
Dia1/8”x1-3/8”L
15
.
Quantity
of 2
Screw Dia1/8”x5/8”L
16
.
Quantity
of 4
Ball Bearing Slide
17.
Quantity
of 4
Screw
Dia1/8”x1-1/4”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Ass
embly Tool Required No.2 Phi
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)
Page 3
Tool List: 3/16" Drill Bit, Drill, Tape Measure, Hammer and Pencil.
Figure 1
Disassemble Metal Slides (16) into
Male Metal Slides and Female
Metal Slides as shown in Figure 1.
Pull the Metal Slides (16) out as far
as possible. There is a small lever
that need to be pushed and held
while pulling the male slide out.
Figure 2
When installing the female ball
bearings, make sure to start from
the front to the back. The front
screw must be inserted into the
second hole as shown in Figure 2.
Attach the Female Ball Bearing
Slide (16) on Left Side Panel (C)
with Screws (8).
Tighten with Phillips screwdriver.
Colorblock 2
-
Drawer Anywhere Storage Ca
binet
-
Linen
Assembly Instructions
P
age 4
16
16
f
r
o
n
t
c
8
8
8
8
16
Figure 3
When installing the female ball
bearings, make sure to start from
the front to the back. The front
screw must be inserted into the
second hole as shown in Figure 2.
Attach the Female Ball Bearing
Slide (16) on Right Side Panel (D)
with Screws (8).
Tighten with Phillips screwdriver.
Figure 4
Insert Cam Locks (3) into
corresponding holes on Back Rail
(E) and Front Middle Rail (F).
Screw Cam Bolts (2) into threaded
holes on Left Side Panel (C). Attach
Left Side Panel (C) to Top Rail (G),
Back Rail (E), and Front Middle Rail
(F) by inserting Wood Dowel (1) and
Cam Bolts (2) into corresponding
holes until all parts meet.
Tighten by rotating Cam Locks (3)
clockwise with Phillips screwdriver.
Repeat steps with Right Side Panel
(D).
Figure 5
Insert Cam Lock (3) into the
corresponding holes in the top of
assembled unit from Figure 4.
Screw Cam Bolts (2) into threaded
holes on Top Panel (A).
Attach the assembled unit from
Figure 4 to Top Panel (A) by
inserting Wood Dowels (1) and Cam
Bolt (2) into corresponding holes
until all panels meet.
Tighten by rotating Cam Locks (3)
clockwise with Phillips screwdriver,
Attach Top Rail (G) to Top Panel (A)
wit Screws (17). Tighten screws
with Phillips screwdriver.
Page 5
F
D
1
1
2
3
3
2
1
3
Figure 6
Insert Cam Locks
(
3
)
into predrilled
holes on assembled unit from
Figure 5.
Screw Cam Bolts (2) into threaded
holes on Bottom Panel (B).
Attach assembled unit from Figure
5 to Bottom Panel (B) by inserting
Wood Dowels (1) and Cam Bolts (2)
into corresponding holes until all
panels meet.
Tighten by rotating Cam Locks (3)
clockwise with Phillips screwdriver.
Figure 7
Attach Legs (P) to Bottom Panel
(B) with Bolts (4).
Tighten Bolts with Allen Wrench
(10).
Page 6
B
2
P
P
1
0
4
Figure 8
Attach Back Panel (H) to the
assembled unit from Figure 7 with
Screws (9).
Tighten Screws with Phillips
screwdriver.
Figure 9
Insert Cam Locks
(2)
into
corresponding holes on Drawer
Bottom Rail (O). Screw Cam Bolt
(2) into threaded hole on Drawer
Back (M).
Attach Drawer Back (M) to Drawer
Bottom Rail (O) by inserting Cam
Bolt (2) into corresponding holes
until Drawer Back (M) and Drawer
Bottom Rail (O) meet.
Tighten by rotating Cam Locks (3)
clockwise with Phillips screwdriver.
Attach Drawer Side Left (K) and
Drawer Side Right (L) to Drawer
Back (M) together making sure the
grooves align and secure them with
Screws (7).
Insert the Drawer Bottom (N) into
the corresponding grooves on the
inside of the panels.
Repeat step for Drawer Back (M) to
attach Drawer Front Panel (I/J).
Repeat this complete step to
assemble the second drawer.
Page 7
H
u p
9
9
9
9
9
9
9
9
I/J
Figure 10
Note: Make sure to attach the
metal slide with the open end
facing towards the back of the
drawer.
Attach Male Metal Slide (16) to
drawer with Screws (8).
Tighten screws by Phillips
screwdriver.
Attach Knob (5) to drawer front with
Small Bolt (6).
Tighten small bolt with Phillips
screwdriver.
Figure 11
Insert drawers into the assembled
unit. Make sure the drawer’s male
ball bearings slide into the side
panel’s female ball bearing slides.
Please make sure ball bearings
slide smoothly in and out.
If the drawer hits adjoining
parts, you can loosen the
screws on male slide and
adjust the height of drawer.
Figure 12
Attach Bracket (11) to Back Panel
using Screws (15). Tighten
Screws (15) using Philips screw
driver.
Mark two desired locations on
wall. Drill two 3/16" holes on wall.
Insert Plastic Anchors (13) into
the 2 holes on wall as shown.
(When doing this, you will need a
hammer help you).
Then attach the Bracket (11) to
wall using screw (14). Tighten
screws (14) using Philips screw
driver.
Page 8
5
J
w all
1 1
1 4
1 3
Figure 13
Move this item close to the wall
Bracket (11) and tie in both
Bracket (11) with Plastic Strap
(12) as shown in diagram.
Anti-tipping hardware must
be used for this product to
avoid tipping and injury.
Figure 14
Your Colorblock 2-Drawer
Anywhere Storage Cabinet –
Linen is ready for use
Page 9
Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s).
If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
service@seidal.com
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
/
