2. Vdwall
  3. LVP515 series
LVP515 series

Vdwall LVP515 series, LVP515 Serial Quick Manual

  • Hello! I am an AI chatbot trained to assist you with the Vdwall LVP515 series Quick Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the maximum number of video signal inputs supported by LVP515?
    What types of video inputs does LVP515 support?
    How can I control LVP515?
    What is the maximum output resolution supported by LVP515?
    How can I change the output resolution of LVP515?
    How can I set the PIP/PBP function on LVP515?
    How can I adjust the PIP/PBP parameters on LVP515?
Address:5B, building C,building C,Nanshan Hi-tech park,Nanshan District,Shenzhen City,
Website:www.videowall.cn TEL
：
+86-755-2675 0210 FAX
：
+86-755-2675 0185
LVP515 series of Quick Guide
LVP515 serial quick user guideV1.0
In order to make sure users can quickly use LVP515 serial LED video processor, we prepared
the<LVP515 serial quick user guide>. About LVP515 deeply setup, adjustment and operation,
please refer to <LVP515 serial user manual>.
Front and rear panel button introduction
LVP515 supports 4 video signal inputs as below：
port
Description
V1、V2
2 *PAL/ NTSC composite video input
S-Video
1 * PAL/ NTSC light color separation video input
VGA
1 * analog signal input of computer
DVI
1 * computer digital signal input
HDMI
1 * Digital HD signal input
EXT.
1 * extension signal input
Note: EXT. interface: LVP515 1 * VIDEO, LVP515S 1* SDI/HD-SDI.
Address:5B, building C,building C,Nanshan Hi-tech park,Nanshan District,Shenzhen City,
Website:www.videowall.cn TEL
：
+86-755-2675 0210 FAX
：
+86-755-2675 0185
LVP515 series of Quick Guide
Step 1: sending card installation
1)Unscrew sending card baffle screw loose, pull out the sending card tray
2) Install the sending card in the corresponding position of the sending card tray and tighten the
screws
3) Connect the card power cable and push the tray into the chassis
4) Tighten the baffle screws to complete the sending card installation
Unscrew the baffle screws and pull
out
Send card
Install the sending card
Connect the power
cable and push the
tray into the
chassis
Tighten the fixing screws to complete it
Step 2: input, output signal connection
1) Turn off the power of all signal source devices
2) Connect the output signals from video sources to corresponding video input ports of LVP515,
such as:
Computer Graphics DVI Output LVP515 DVI input
Camera AV output LVP515 V1, V2 input
3) Connect LVP515 DVI outputs to DVI inputs of sending cards
4) Connect sending card RJ45 cables to LED receiving cards
5) Connect LVP515 VGA output to LCD display(used as monitor)
Address:5B, building C,building C,Nanshan Hi-tech park,Nanshan District,Shenzhen City,
Website:www.videowall.cn TEL
：
+86-755-2675 0210 FAX
：
+86-755-2675 0185
LVP515 series of Quick Guide
Step 3:Connect power and power on
1) Make sure all input and output connection correct.
2) Connect power to LVP515 and turn on it.
3) Power on the video source devices.
Step 4: input signal selection
LVP515 boot, LCD screen will show the right information..
1) Line 1 displays the currently selected input source, eg "Input = DVI"
2) Line 2 shows the status of the current input source
If no valid signal input, then display: "no valid signal input", while the corresponding input button
light flashes, the screen is black;
If the signal is valid, then it will show the input signal format, such as: "1080p_60Hz"
3) Line 3 shows the effect of signal switching, such as "seamless switching" or "fade in"
Press the input signal button at this time, you can select the corresponding input source
Step 5: output resolution setup
After turning on LVP515
1) Press Setup key, then press knob (i.e.OK button), and the LVP515 enters the setup menu
2) Press the ↑ key to switch to the setup menu item 2: Output Resolution, Rotate knob to change
the output resolution. Select the width and height are greater than the actual output of the LED
screen pixel resolution, press OK key to save.
3) The video processor automatically restarts and applies the new resolution
Step 6: output image width and height setup
After the LVP515 restart，
1) Press Setup key, then press OKto enter the setup menu, press ↑ to scroll to the menu output width,
turn the knob to change the output width to be the same as the actual width of the LED screen, just
press OK to save.
2) and then press ↑ to scroll to the menu output height, turn the knob to change the output height
and the actual height of the LED screen pixels to be the same, press OK to save.
3) Press Setup again to exit the setup menu to complete the setup
Step 7: computer resolution setup
1) Enter the computer graphics card control interface, set the multiple display options to "copy
Input = DVI
1080p_60hz
Seamless switching
Address:5B, building C,building C,Nanshan Hi-tech park,Nanshan District,Shenzhen City,
Website:www.videowall.cn TEL
：
+86-755-2675 0210 FAX
：
+86-755-2675 0185
LVP515 series of Quick Guide
mode", "extend mode" or "dual display mode"
2) In the change resolution option, select the display LVP515 resolution is not less than the output
resolution of LVP515, then LVP515 panel LCD screen will display the current computer graphics
card resolution.
Step 8: full \ part display
1) Press the DVI key to select the DVI signal input to ensure that the DVI input signal resolution is
not less than the LVP515 output resolution
2) press the Bypass button, the button indicator light on, LED screen is under pixel to pixel part
display situation. Picture is not compressed.
3) Press the Bypass key again, the button indicator is off, the LED screen is full screen display, and
the image is compressed to the LED screen.
Step 9:turn on PIP / PBP function
1) In the single-screen display state, press the signal button to select the signal as the background
signal
2) Press the ON / OFF button, the panel LCD will indicate: PIP =
3) Press the key to select the signal as the PIP / PBP signal, that is, turn on the PIP / PBP function,
enter the dual screen display status
4) The LVP515 can store 3 different PIP / PBP modes, press the mode key "M1 ~ 3" to select
5) In the PIP / PBP open mode, press the ON / OFF button to turn off the PIP / PBP function and
return to the single screen display status
Step 10: set the PIP / PBP parameters
1) LVP515 enter the dual screen display state, press the Setup key, then press OK button to enter
the setup menu.
2) Press ↑ to scroll to 4 main picture settings: main out width, main out H_ start, main out height,
main out v_start
3) Rotate the knobto adjust the value of each setting item, and press ok to save
4) continue to press the ↑ key to flip to 4 PIP screen settings:PIP out width, PIP output H_start, PIP
out height, PIP out v_ start
5) Rotate the knob to adjust the value of each setting item, and press ok key to save
6) Press the mode keys "M1 ~ 3" to save the above three groups of main pictures and PIP
Address:5B, building C,building C,Nanshan Hi-tech park,Nanshan District,Shenzhen City,
Website:www.videowall.cn TEL
：
+86-755-2675 0210 FAX
：
+86-755-2675 0185
LVP515 series of Quick Guide
picture settings
Appendix: Revised record sheet
time
Description
draft
2017.5.9
The first release
Lts
/