Panasonic SC-ALL70T Operating Instructions Manual

Brand: Panasonic

Model: SC-ALL70T

Category: Speaker sets

Type: Operating Instructions Manual

2015/06/06

EB EG GN

SQT0935-1

Operating Instructions

Home Theater Audio System

Model No. SC-ALL70T

Thank you for purchasing this product.

Please read these instructions carefully before using this product,

and save this manual for future use.

Model number suffix “EB” denotes UK model.

Included Installation Instructions

The installation work should be done by a qualified installation specialist. (>13 to 18)

Before commencing work, carefully read these installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them when maintaining or moving this system.)

SC-ALL70T-SQT0935.book 1 ページ２０１５年４月２８日　火曜日　午前１０時５分

2SQT0935

Safety precautions

Unit

≥To reduce the risk of fire, electric shock or

product damage,

jDo not expose this unit to rain, moisture,

dripping or splashing.

jDo not place objects filled with liquids, such

as vases, on this unit.

jUse only the recommended accessories.

jDo not remove covers.

jDo not repair this unit by yourself. Refer

servicing to qualified service personnel.

≥To prevent injury, this apparatus must be

securely attached to the wall in accordance

with the installation instructions.

AC mains lead

≥To reduce the risk of fire, electric shock or

product damage,

Ensure that the power supply voltage

corresponds to the voltage printed on this unit.

Insert the mains plug fully into the socket outlet.

jDo not pull, bend, or place heavy items on

the lead.

jDo not handle the plug with wet hands.

jHold onto the mains plug body when

disconnecting the plug.

jDo not use a damaged mains plug or socket

outlet.

≥The mains plug is the disconnecting device.

Install this unit so that the mains plug can be

unplugged from the socket outlet immediately.

Button-type battery (Lithium battery)

≥Risk of fire, explosion and burns. Do not

recharge, disassemble, heat above 60 oC or

incinerate.

≥Keep the Button-Type battery out of the reach

of children. Never put Button-Type battery in

mouth. If swallowed call your doctor.

Small object

≥Keep the screws out of reach of children to

prevent swallowing.

≥Keep the button-type battery out of reach of

children to prevent swallowing.

Never put Button-Type battery in mouth.

If swallowed call your doctor.

Unit

≥Do not place sources of naked flames, such

as lighted candles, on this unit.

≥This unit may receive radio interference

caused by mobile telephones during use. If

such interference occurs, please increase

separation between this unit and the mobile

telephone.

≥This unit is intended for use in moderate

climates.

≥Product Identification Marking is located on

the bottom of the unit.

Placement

≥Place this unit on an even surface.

≥To reduce the risk of fire, electric shock or

product damage,

jDo not install or place this unit in a

bookcase, built-in cabinet or in another

confined space. Ensure this unit is well

ventilated.

jDo not obstruct this unit’s ventilation

openings with newspapers, tablecloths,

curtains, and similar items.

jDo not expose this unit to direct sunlight,

high temperatures, high humidity, and

excessive vibration.

Button-type battery (Lithium battery)

≥Danger of explosion if battery is incorrectly

replaced. Replace only with the type

recommended by the manufacturer.

≥Insert with poles aligned.

≥Mishandling of batteries can cause electrolyte

leakage and may cause a fire.

jRemove the battery if you do not intend to

use the remote control for a long period of

time. Store in a cool, dark place.

jDo not heat or expose to flame.

jDo not leave the battery(ies) in a car

exposed to direct sunlight for a long period

of time with doors and windows closed.

≥When disposing of the batteries, please

contact your local authorities or dealer and

ask for the correct method of disposal.

WARNING CAUTION

SC-ALL70T-SQT0935.book 2 ページ２０１５年４月２８日　火曜日　午前１０時５分

Precautions

SQT0935 3

Caution for AC Mains Lead

(For the AC mains plug of three

pins)

For your safety, please read the following text

carefully.

This appliance is supplied with a moulded three

pin mains plug for your safety and convenience.

A 10-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating of

10-ampere and that it is approved by ASTA or

BSI to BS1362.

Check for the ASTA mark Ï or the BSI mark Ì

on the body of the fuse.

If the plug contains a removable fuse cover you

must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be

used until a replacement cover is obtained.

A replacement fuse cover can be purchased

from your local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the

type of AC mains plug (figures A and B).

Confirm the AC mains plug fitted and follow the

instructions below.

Illustrations may differ from actual AC mains

plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse

cover.

Figure A

Figure B

Fuse cover

Figure A Figure B

Fuse

(10 ampere)

Fuse

(10 ampere)

About descriptions in these operating instructions

≥Pages to be referred to are indicated as “>±±”.

≥Labels on this unit and the remote control are indicated as [±±] in these operating instructions.

≥The illustrations shown may differ from your unit.

≥These operating instructions are applicable to model SC-ALL70T for variety of regions. Unless otherwise indicated,

illustrations in these operating instructions are of the model for the United Kingdom and Ireland.

≥Operations in this operating instructions are described mainly with the remote control, but you can perform the operations

on the main unit if the controls are the same.

SC-ALL70T-SQT0935.book 3 ページ２０１５年４月２８日　火曜日　午前１０時５分

4SQT0935

Table of contents

Safety precautions ........................................................................................... 2

Caution for AC Mains Lead ............................................................................. 3

Before use

Supplied items.................................................................................................. 5

Control reference guide................................................................................... 6

Getting started

Step 1 Connections ......................................................................................... 9

Step 2 Placement .......................................................................................... 13

Step 3 Active subwoofer wireless connection ........................................... 19

Step 4 Network settings ............................................................................... 19

Operations

Using this system .......................................................................................... 23

Streaming music over the network .............................................................. 24

Bluetooth® operations ................................................................................... 27

3D sound ......................................................................................................... 28

Sound menu ................................................................................................... 28

Setup menu ..................................................................................................... 30

Linked operations with the TV

(VIERA Link “HDAVI ControlTM”) .............................................................. 33

Reference

Troubleshooting ............................................................................................. 35

About Bluetooth® ........................................................................................... 40

Unit care .......................................................................................................... 41

Licenses .......................................................................................................... 41

Specifications ................................................................................................. 42

Limited Warranty (ONLY FOR AUSTRALIA) ................................................ 47

SC-ALL70T-SQT0935.book 4 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Operations

Reference

Before use

Precautions

SQT0935 5

Before use

Supplied items

Check the supplied accessories before using this system.



≥Product numbers are correct as of April 2015. These may be subject to change.

≥The supplied AC mains lead is for use with this system only.

Do not use it with other equipment. Also, do not use cords from other equipment with this system.

This system (SC-ALL70T)

∏1 Main unit (speaker)

(SU-ALL70T)

∏1 Active subwoofer

(SB-ALL70T)

Accessories

∏1 Remote control

(with a battery)

(N2QAYC000098)

∏1 IR Blaster

(SFQ0014)

∏2 Wall mount brackets

(RMQ2281A, RMQ2281B)

∏1 AC mains lead for the main unit

For the United Kingdom and Ireland

(SFQ0017)

For Continental Europe

(SFQ0015)

For Australia and New Zealand

(SFQ0021)

∏1 AC mains lead for the active subwoofer

For the United Kingdom and Ireland

(SFQ0018)

For Continental Europe

(SFQ0016)

For Australia and New Zealand

(SFQ0022)

∏2 Screws

(XYN5+J14JK)

SC-ALL70T-SQT0935.book 5 ページ２０１５年４月２８日　火曜日　午前１０時５分

6SQT0935

Control reference guide

1 [ ] NFC touch area (>27)

2[Í/I] Standby/on switch (Í/I)

Touch to switch the unit from on to standby

mode or vice versa. In standby mode, the

unit is still consuming a small amount of

power.

3[VOLj][VOLi] Adjust the volume of this

system (>23)

4 [INPUT] Select the input source (>23)

5 [ -PAIRING]

≥Select the Bluetooth® device as the

source (>23)

≥Bluetooth® pairing (>27)

≥Disconnecting a Bluetooth® device (>27)

6 Remote control signal sensor for table top

layout (>8)

7 Remote control signal sensor for wall

mounting layout (>8)

8 Display

9 WIRELESS LINK indicator (>19)

§These switches work just by touching the

marks. Each time you touch the switch,

there will be a beep sound.

The beep sound setting can be changed.

(>30)

This system (Front)

3 42 5

Main unit

Active subwoofer

SC-ALL70T-SQT0935.book 6 ページ２０１５年４月２８日　火曜日　午前１０時５分

Before use

SQT0935 7

1 HDMI AV OUT (TV (ARC)) terminal (ARC

compatible) (>9, 10)

2 HDMI AV IN (BD/DVD) terminal (>11)

3 OPTICAL DIGITAL AUDIO IN (TV) terminal

(>10)

4 LAN terminal (>22)

5 Ir SYSTEM terminal (>11)

6 AC IN terminal (>12)

7[Í/I] Active subwoofer on/off button (>19)

§1 USB port (for service use only)

§2 The I/D SET button is only used when the

main unit is not paired with the active

subwoofer. (>39)

This system (Rear)

Main unit

Active subwoofer

SC-ALL70T-SQT0935.book 7 ページ２０１５年４月２８日　火曜日　午前１０時５分

8SQT0935

1[Í] Turn the main unit on or off (>23)

2 [INPUT] Select the input source (>23)

3 [SETUP] Select the setup menu (>30)

4 [SOUND] Select the sound menu (>28)

5 [ -PAIRING]

≥Select the Bluetooth® device as the

source (>23)

≥Bluetooth® pairing (>27)

≥Disconnecting a Bluetooth® device (>27)

6[jVOL i] Adjust the volume of this system

(>23)

7 [MUTE] Mute the sound (>23)

8[4][OK][3] Select and confirm the option

∫Before using for the first time

Remove the insulation sheet A.

≥Dispose of the insulation sheet responsibly

after removing it.

∫To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥Set the button-type battery with its (i) mark

facing upward.

∫About remote control signal sensor

The remote control signal sensor is located

on the main unit.

≥Use the remote control within the correct

operation range.

Distance: Within approx. 7 m directly in front

Angle: Approx. 30oleft and right

For table top layout

For wall mounting layout

BRemote control signal sensor for table top

layout

CRemote control signal sensor for wall

mounting layout

Remote control

SOUND

INPUT

SETUP











SC-ALL70T-SQT0935.book 8 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Before use

SQT0935 9

Getting started

Step 1 Connections

≥Turn off all equipment before connection and

read the appropriate operating instructions.

Do not connect the AC mains lead until all

other connections are completed.

1 Verify if the TV’s HDMI terminal is

labelled “HDMI (ARC)”.

2 Make the connection.

∫HDMI (High-Definition Multimedia

Interface)

≥The HDMI connection supports VIERA Link “HDAVI

Control” (>33) when used with a compatible

Panasonic TV.

≥Use the ARC compatible High Speed HDMI Cables.

Non-HDMI-compliant cables cannot be utilised.

≥It is recommended that you use Panasonic’s HDMI

cable.

∫HDMI standby pass-through

Even if the main unit is in standby mode, the audio and/

or video signal from the device connected to the HDMI

AV IN terminal will be sent to the TV connected to the

HDMI AV OUT terminal (the sound will not be output

from this system).

∫3D compatibility

Compatible with FULL HD 3D TV and Blu-ray Disc

player.

≥The main unit can pass-through the 3D video signal

from a 3D compatible Blu-ray Disc player to a FULL

HD 3D TV.

∫4K/60p compatibility

Compatible with 4K Ultra HD TV and Blu-ray Disc

player.

≥This system can pass-through the 4K content of a 4K

compatible equipment to a 4K Ultra HD TV.

≥When connecting to 4K compatible equipment and

4K Ultra HD TV, use High Speed HDMI cables which

support 18 Gbps bandwidth.

Connection with the TV

Connection differs depending on the label

printed next to the HDMI terminal.

Labelled “HDMI (ARC)”:

Connection [A]

Not Labelled “HDMI (ARC)”:

Connection [B]

∫What is ARC?

ARC is an abbreviation of Audio Return Channel, also

known as HDMI ARC. It refers to one of the HDMI

functions. When you connect the main unit to the

terminal labelled “HDMI (ARC)” on the TV, the optical

digital audio cable that is usually required in order to

listen to sound from a TV is no longer required, and TV

pictures and sound can be enjoyed with a single HDMI

cable.

SC-ALL70T-SQT0935.book 9 ページ２０１５年４月２８日　火曜日　午前１０時５分

10 SQT0935

AHDMI cable

BOptical digital audio cable

≥When you use the optical digital audio cable, insert

the tip correctly into the terminal.

[A] Labelled “HDMI (ARC)”

HDMI IN (ARC)



Be sure to connect to the TV’s ARC

compatible terminal. (Refer to the operating

instructions for the TV.)

[B] Not Labelled “HDMI

(ARC)”

HDMI IN

OPTICAL OUT





SC-ALL70T-SQT0935.book 10 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

SQT0935 11

You can direct the audio signal from the

connected Blu-ray Disc player, DVD player, Set

Top Box, etc. to this system.

Preparation

≥Connect the main unit to the TV. (>9)

AHDMI cable

Depending on how the main unit is setup, it may

block the TV’s remote control signal sensor,

stopping the TV’s remote control from working.

Use the supplied Ir system cable if this occurs.

The TV remote control signals received by the

main unit are sent to the TV to operate it.

≥For the operation range, refer to page 8.

≥Do not use any other IR Blaster except the

supplied one.

1 Connect the jack plug to the main

unit’s Ir SYSTEM terminal.

AIR Blaster (supplied)

2 Place the infrared emitter in sight of

the TV’s remote control signal sensor.

Placement example

On the rear of the main unit:

BTV remote control signal sensor

CInfrared emitter

DAdhesive tape

Connection from an HDMI

compatible device



≥Refer to the operating instructions of the connected

HDMI compatible device for the necessary setting, to

output the video and audio signals.

≥When connecting to 4K compatible equipment and 4K

Ultra HD TV, use High Speed HDMI cables which support

18 Gbps bandwidth.

HDMI OUT



e.g., Blu-ray Disc player

Using the IR Blaster

(When the remote control does not

work properly)









SC-ALL70T-SQT0935.book 11 ページ２０１５年４月２８日　火曜日　午前１０時５分

12 SQT0935

3 Aim the TV’s remote control at this

system’s remote control sensor and

operate the TV. ≥Connect only after all other connections

are completed.

ATo a household mains socket

BAC mains lead for the main unit (supplied)

CAC mains lead for the active subwoofer

(supplied)

§Insert the AC mains lead fully into the main

unit.

≥This system consumes a small amount of AC

power (>42) even when it is turned off. In the

interest of power conservation, if you will not

be using this system for a long time, unplug it

from the household mains socket.



≥For the location of the TV’s remote control signal sensor,

refer to the operating instructions for the TV.

≥Select a location that suits the environment.

≥Make sure to clean the surface, where the adhesive tape

is to be attached.

≥If you peel off the adhesive tape, the surface may

become damaged and exposed adhesive may remain.

Once you have confirmed the TV is operating correctly,

secure it by attaching the adhesive tape.

≥When the TV receives signals from both its remote

control and the IR Blaster, their signals may interfere with

each other, making it impossible for you to operate the

TV.

Try using the TV’s remote control from a different angle.

AC mains lead connection

Saving energy

The main unit is designed to conserve its

power consumption and save energy.

≥The main unit will automatically switch to

standby mode when no signal is input and

no operation is performed for approx. 20

minutes. Refer to page 30, “AUTO

POWER DOWN” to turn this function off.







SC-ALL70T-SQT0935.book 12 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Precautions

SQT0935 13

Step 2 Placement

When carrying the active subwoofer

Take care not to damage the inside speaker

unit.



≥The speaker protection cover is attached to the speaker

unit inside the subwoofer. Remove it before use.

≥When the subwoofer is brought close to CRT TVs and

other display devices, the magnets in the speaker may

cause some colour irregularities or image distortion. If

this happens, move the active subwoofer to a place

where these symptoms do not occur.

≥Interference may occur if the TV has wireless LAN

functionality, causing some communication problems

(sound is interrupted, sound skips, there is a lot of noise,

etc.). If this happens, move the active subwoofer to a

place where interference does not occur.

Interference may occur if you are using other

devices (wireless LAN/microwave ovens/

cordless phones, etc.) that use the 2.4 GHz

frequency band, causing some communication

problems (sound is interrupted, sound skips,

there is a lot of noise, etc.).

If this happens, separate the other electronic

equipment from the main unit and active

subwoofer so that interference does not occur.

Safety Precautions

Professional installation is required.

The installation should never be done by

any other than a qualified installation

specialist.

PANASONIC DISCLAIMS ANY PROPERTY

DAMAGE AND/OR SERIOUS INJURY,

INCLUDING DEATH RESULTING FROM

IMPROPER INSTALLATION OR

INCORRECT HANDLING.

≥Be sure to install the main unit as indicated within this

operating Instructions.

≥Attach using techniques suited to the structure and

materials of the installation location.

Caution

≥This system is to be used only as indicated

in these instructions. Failure to do so may

lead to damage to the amplifier and/or the

speaker, and may result in the risk of fire.

Consult a qualified service person if

damage has occurred or if you experience

a sudden change in performance.

≥Do not attempt to attach the main unit to a

wall using methods other than those

described in this manual.



≥Do not hold the main unit in one hand to avoid injury,

you may drop the main unit when carrying it.

≥To prevent damage or scratches, lay down a soft

cloth and perform the assembly on it.

The active subwoofer

Wireless interference

AMain unit/active subwoofer

BWireless router, cordless phone and other

electronic devices

SC-ALL70T-SQT0935.book 13 ページ２０１５年４月２８日　火曜日　午前１０時５分

14 SQT0935

Choose a placement method that suits you best.

When placing the main unit in a rack or

on a table

≥Place the main unit on a flat and horizontal

surface.

When attaching the main unit to a wall

≥Place the main unit on a flat and vertical

surface.

∫When placing the main unit in front

of the TV

The main unit may block or interfere with the

TV’s various sensors (C.A.T.S. (Contrast

Automatic Tracking System) sensor, remote

control sensor, etc.) and the 3D Eyewear

transmitters on a 3D compatible TV.

≥If interference occurs, move the main unit

further away from the TV. If the TV still does

not function correctly, try using it in a rack or in

the wall mount position.

∫If the TV’s remote control sensor is

blocked by the main unit

Try using the TV’s remote control from a

different angle. If the problem persists, you can

use the supplied IR Blaster to relay the signal to

the TV. (>11)

Selecting the placement

method

Page 15

Page 16



≥Place the active subwoofer within a few meters of the

main unit and in a horizontal position with the top

panel facing upward.

≥Do not use the main unit or the active subwoofer in a

metal cabinet.

≥Placing the active subwoofer too close to the walls

and corners can result in excessive bass. Cover walls

and windows with thick curtains.

≥Keep magnetised items away. Magnetised cards,

watches, etc., can be damaged if placed too close to

the main unit and active subwoofer.

SC-ALL70T-SQT0935.book 14 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Precautions

SQT0935 15

Additionally required accessories (commercially available)

≥Fall prevention cord ..................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ............................................................................ k 2



≥Use commercially available screws that are capable of supporting over 26 kg.

≥Use a cord that is capable of supporting over 26 kg (with a diameter of about 1.5 mm).

≥Lay the unit on a blanket or soft cloth for assembly.

1 Attach the cord to the main unit.

ACord§

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45o (as illustrated above).

2 Place the main unit in the desired position and attach each cord onto the rack or table.

≥Make sure that the slack of the cord is minimal.

≥Do not lean the main unit against the TV or wall.

BScrew eye

≥Attach at a position capable of supporting over 26 kg.

≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

When placing the main unit in a rack or on a table





SC-ALL70T-SQT0935.book 15 ページ２０１５年４月２８日　火曜日　午前１０時５分

16 SQT0935

The main unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the

screw used and the wall are strong enough to support the weight of at least 26 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 3 for details about the required screws.

≥Be sure to attach the fall prevention cord as a secondary safety measure.

Supplied accessories

Additionally required accessories (commercially available)

≥Screws for wall mounting............................................................................................................. k 2

≥Fall prevention cord..................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ........................................................................... k 2



≥Use a cord that is capable of supporting over 26 kg (with a diameter of about 1.5 mm).

≥Lay the unit on a blanket or soft cloth for assembly.

1 Attach the cord to the main unit.

ACord§

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45o (as illustrated above).

When attaching the main unit to a wall

∏2 Screws ∏2Wall mount

brackets



SC-ALL70T-SQT0935.book 16 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Precautions

SQT0935 17

2 Attach the wall mount brackets to the main unit.

AWall mount bracket (supplied)

BScrew (supplied)

3 Drive a screw into the wall.

≥Use the measurements indicated below to identify the screwing positions on the wall.

≥Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the touch keys.

≥Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

CAt least 30 mm

D‰4.0 mm

E‰7.0 mm to ‰9.4 mm

FWall or pillar

G2.5 mm to 3.5 mm

H374 mm I315 mm J261 mm

K41 mm L125.5 mm MWall mounting hole













  



SC-ALL70T-SQT0935.book 17 ページ２０１５年４月２８日　火曜日　午前１０時５分

18 SQT0935

4 Fit the main unit securely onto the screw(s).

5 Secure the cord to the wall.

≥Make sure that the slack of the cord is minimal.

AScrew eye

BCord

DO DO NOT

≥Move the speaker so

that the screw is in

this position.

≥In this position, the

speaker will likely fall

if moved to the left or

right.





SC-ALL70T-SQT0935.book 18 ページ２０１５年４月２８日　火曜日　午前１０時５分

Getting started

Precautions

SQT0935 19

Step 3 Active

subwoofer wireless

connection

Preparation

≥Turn on the main unit.

1Press [Í/I].

The active subwoofer will still consume a small

amount of power even when it is turned off.

2 Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



≥The wireless link will be activated when the main unit and

the active subwoofer are both turned on.

Step 4 Network

settings

You can stream music from an iOS device, an

AndroidTM device or a PC, etc. to this system’s

speakers by using the Qualcomm® AllPlayTM

smart media platform or DLNA feature. To use

these features, this system must join the same

network as the compatible device.

≥Please update the system’s firmware after the

network settings are complete. (>32,

“Firmware update”)

Choose a network setting method from the

following.

Wireless LAN connection

Method 1:

“Using an Internet browser” (>20)

≥You can access this system’s network

settings from the Internet browser on your

smartphone or PC, etc.

Method 2:

“Using WPS (Wi-Fi Protected SetupTM)”

(>21)

≥If your wireless router supports WPS, you

can set up a connection by either pressing

the WPS button, or entering the WPS PIN

code.

Wired LAN connection

Method 3:

“Using a LAN cable” (>22)

≥You can make a stable connection to the

network with a LAN cable.



≥To cancel wireless connection setting partway through,

press [INPUT].

– “WAIT” blinks on the display for approx. 1 minute.

SC-ALL70T-SQT0935.book 19 ページ２０１５年４月２８日　火曜日　午前１０時５分

20 SQT0935

≥Do not connect a LAN cable. Doing so will

disable the Wi-Fi® function.

≥The following explanations are based on a

smartphone.

1 Turn this system on.

2 Press [SETUP] on the remote

control repeatedly to select

“NET SETUP”.

3Press [4][3] on the remote control

to select “MANUAL” and then press

[OK].

4Press [4][3] on the remote control

to select “OK?YES” and then press

[OK].

≥

After pressing [OK], the previous network connection

you have set with this system will be cleared.

≥Proceed to the next step after the display on the

main unit changes from a flashing “WAIT” display to

a flashing “SETTING” display.

5 Go to Wi-Fi settings on your

compatible device.

≥Make sure that DHCP is enabled for the network

setting on your compatible device.

6 Select “AllPlay _AJ” to

connect to this system.

≥“  ” stands for a digit that is unique to each set.

≥

This can take up to 1 minute to appear in your Wi-Fi list.

[iOS_device] : The settings page will be automatically

displayed in the Internet browser.

[Except_iOS_device] : Open the Internet browser and

refresh the page to display the settings page.

≥If the settings page is not displayed, type “http://

172.19.42.1/” into the URL address field.

7 Type a device name and then select

“Next”.

≥The device name will be displayed as this system's

name on the network.

≥The guaranteed limit is 32 characters.

≥The device name is set when “Next” is selected.

≥You can also change the device name after the

network connection is set up. (>22, “To make

network-related settings”)

8 Select your network name (SSID)

and type the password.

≥Check the wireless router for the network name

(SSID) and the password.

≥A list of network names (SSIDs) will be appeared

when you select the “Network Name” box.

≥To show the characters typed in the “Password”

box, select “Show Password”.

≥If your network requires specific settings, deselect

“DHCP” to disable DHCP.

– You can use specific IP address, subnet mask,

default gateway, primary DNS, etc.

9 Select “Connect” to apply the

settings.

≥On the main unit’s display, “SUCCESS” appears

when the connection is established. (“ ” will be

displayed.)

– If “FAIL” is displayed press [OK], check the

network name (SSID) and the password, and

then try the setting again.

≥Depending on the device, the connection complete

screen may not be displayed.

Method 1:

Using an Internet browser

Settings Wi-Fi settings

●●●●●●●●

SC-ALL70T-SQT0935.book 20 ページ２０１５年４月２８日　火曜日　午前１０時５分

Page is loading ...

Panasonic SC-ALL70T Operating Instructions Manual

Brand: Panasonic

Model: SC-ALL70T

Category: Speaker sets

Type: Operating Instructions Manual

Download PDF

report

Panasonic SC-ALL70T Operating Instructions Manual

Panasonic SC-ALL70T Operating Instructions Manual

Related papers

Other documents