CyberView MD-19QD User manual

Manual ML24V02A -- Generation 4 -- www.EclipseRackmount.com

User Manual

Designed/Manufactured by Austin Hughes and Distributed by Eclipse Rackmount, Inc.

1U 19" Quad Display Drawer

MD-19QD

Options Available:

- DC Power

Page 02 -- ML24V02A -- www.EclipseRackmount.com

Legal Information

First English printing, October 2002

Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness

of the contents. The information in this document is subject to change without notice. We are not liable for any injury or

loss that results from the use of this equipment.

Safety Instructions

Please read all of these instructions carefully before you use the device. Save this manual for

future reference.

■ Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.

■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with

temperatures not exceeding 40º Celsius (104º Fahrenheit).

■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing

damage to other equipment or injury to persons nearby.

■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the

power supply. Proper air convection is necessary to keep it from overheating.

■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.

■ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current

labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed

on the equipment’s ratings label.

■ Observe all precautions and warnings attached to the equipment.

■ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being

damaged by transient over-voltage.

■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power

supply or on other hardware may cause damage, ﬁ re or electrical shock.

■ Only qualiﬁ ed service personnel should open the chassis. Opening it yourself could damage the equipment and

invalidate its warranty.

■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualiﬁ ed service personnel.

What the warranty does not cover

■ Any product, on which the serial number has been defaced, modiﬁ ed or removed.

■ Damage, deterioration or malfunction resulting from:

□ Accident, misuse, neglect, ﬁ re, water, lightning, or other acts of nature, unauthorized product modiﬁ cation, or

failure to follow instructions supplied with the product.

□ Repair or attempted repair by anyone not authorized by us.

□ Any damage of the product due to shipment.

□ Removal or installation of the product.

□ Causes external to the product, such as electric power ﬂ uctuation or failure.

□ Use of supplies or parts not meeting our speciﬁ cations.

□ Normal wear and tear.

□ Any other causes which does not relate to a product defect.

■ Removal, installation, and set-up service charges.

Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

Any changes or modiﬁ cations made to this equipment may void the user’s authority to operate this equipment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

■ Re-position or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Page 03 -- ML24V02A -- www.EclipseRackmount.com

< Part. 3 >

< Part. 4 >

Options

3.1 48V, 24V or 12VDC power

P.7

< Part. 2 >

Specifications / OSD

2.1 Product Specifications

2.2 On-Screen Display Operation ( OSD )

P.4 - 5

P.6

< Part. 1 >

MD-19QD

1.1 Package Contents

1.2 Structure Diagram & Dimensions

1.3 Installation

Contents

P.1

P.1 - 2

P.3

Contents

Quad Display Connection & Operation

4.1 QD Connection

4.2 QD ALARM Connection & Operation

4.3 QD Remote Control Connection & Operation

4.4 QD OSD Operation

4.5 QD On-Screen Menu

4.6 QD VCR Operation

4.7 QD Speciﬁ cation

P.8

P.9 - 10

P.11 - 15

P.16

P.17 - 19

P.20

P.21

Page 04 -- ML24V02A -- www.EclipseRackmount.com

■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.

■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive

dust, dirt, heat, water, moisture and vibration.

The equipment comes with the standard parts shown in package content. Check and make sure they are

included and in good condition. If anything is missing, or damaged, contact the supplier immediately.

Unpacking

Before Installation

How To Clean Your LCD Monitor

Caution :

■ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or

plugging your monitor into an electrical outlet.

■ When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can

scratch or damage your display. Pressure damage is not covered under warranty.

■ Use only cleansers made speciﬁ cally for cleaning monitors and monitor screens. Cleansers not made to

clean monitors and monitor screens can scratch the LCD display or strip off the ﬁ nish.

■ Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly

onto the screen or case can cause damage which is not covered under warranty.

■ Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based

paper product such as paper towels can scratch your LCD screen.

Cleaning Your Monitor

To clean your LCD safely, please follow these steps :

Disconnect the power cord.

Gently wipe the surface using a clean, dry microﬁ ber cloth. Use as little pressure as possible.

1

2

Cleaning Tough Marks and Smudges

To remove tough marks and smudges, please follow these steps :

Disconnect the power cord.

Spray a small amount of non-abrasive cleanser on a microﬁ ber cloth.

Gently wipe the surface. Use as little pressure as possible.

Wait until your monitor is completely dry before plugging it in and powering it up.

1

2

Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your

microf ber cloth f rst, not directly on the parts you are cleaning.

3

4

Page 05 -- ML24V02A -- www.EclipseRackmount.com

1

2

LCD panel

Installation Slide

1

2

3

4

3

LCD OSD membrane

Quad display control membrane

Thumb Screw

< 1.1 > Package Contents

< Part 1 >

MD-19QD unit X 1

- 6ft VGA cable X 1

- Power cord X 1

- M6 screw, cage nut & cup washer X 8

< 1.2 > Structure Diagram

The above package content is only for the base model ( VGA only ).

It varies with options such as DC power.

5

S

et

u

p

VC

R

SE

Q

<

>

Quad

Di

s

pl

a

y

Co

n

tro

l

L

CD

O

S

D Men

u

4

Page 06 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

The weight is only for the base models. It varies with accessories & options

such as DC power.

< 1.2 > Dimensions

Front View

Side View

UNIT : mm

1mm = 0.03937 inch

Top View

Model

Product Dimension

(W x D x H)

Packing Dimension

(W x D x H)

Net

Weight

Gross

Weight

MD-19QD

442 x 650 x 44 mm

17.4 x 25.6 x 1.73"

595 x 860 x 140 mm

23.4 x 33.9 x 5.5”

12.5 kg

28 lb

18.5 kg

41 lb

Page 07 -- ML24V02A -- www.EclipseRackmount.com

■ Fix the display drawer into the rack.

Complete the installation

Step

3

■ Insert the left and right rear mounting brackets into

the display drawer.

Step

1

< 1.3 > Installation - How to install Installation Slides

Step

2

■ Measure the depth of the front and rear mounting rails.

■ Align each rear mounting bracket to a suitable length.

M6 screw, cage nut & cup washer x 8 are provided.

Page 08 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

Power Power Supply Range Auto-sensing 100 to 240VAC,

50 / 60Hz

Power Consumption

Screen display ON 25W or less

Power saving mode 4W or less

Power button OFF 1W or less

Regulatory Safety Approval FCC & CE

LCD

Panel

Manufacturer

Panel Size ( diagonal ) 19-inch TFT color LCD

Display pixel ( dots x lines ) 1280 x 1024

Brightness ( typ. ) 250

Contrast Ratio ( typ. ) 1000:1

Color 16.7 M

Viewing Angle ( L/R/U/D ) 80/80/80/80

Response Time ( ms ) 5

Dot pitch ( mm ) 0.294

Display Area ( mm ) 376.32H x 301.05V

Surface treatment Haze 25%, Hard-coating

Surface hardness 3H

Backlight Type CCFL

MTBF ( hrs ) 50,000

< 2.1 > Product Specifications

< Part 2 >

Video

Connectivity

Analog VGA Analog 0.7Vp-p

Environmental

Conditions

Operating Temperature 0 to 50°C degree

Humidity 20~90%, non-condensing

Storage

Temperature -5 to 60°C degree

Humidity 5~90%, non-condensing

Shock 10G acceleration (11ms duration)

Vibration 5~500Hz 1G RMS random

Page 09 -- ML24V02A -- www.EclipseRackmount.com

Physical

Specification

Product ( W x D x H )

442 x 650 x 44 mm

17.4 x 25.6 x 1.73 inch

Packing ( W x D x H )

595 x 860 x 140 mm

23.4 x 33.9 x 5.5 inch

Net W

eight 12.5 kgs / 28 lbs

Gross Weight 18.5 kgs / 41 lbs

Applicable

Format

VGA Input PC Signal 1280 x 1024 x 60 / 75Hz

1280 x 960 x 60Hz

1280 x 760 x 60 / 75Hz

1152 x 864 x 75Hz

1024 x 768 x 60 / 70 / 75Hz

848 x 480 x 60Hz

800 x 600 x 60 / 72 / 75Hz

720 x 400 x 70Hz

640 x 480 x 60 / 72 / 75Hz

640 x 400 x 70Hz

640 x 350 x 70Hz

Page 10 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

< 2.2 > On-Screen Display Operation ( OSD )

Exit the OSD screen

Toggle analog, digital & video connection (DVI-D and video options only)

Scrolls through menu options and adjusts the displayed control

(To auto adjustment by pressing the button for 5 seconds)

Display the OSD menu

Power on / off LCD

Power light

Green = On

Orange = Power saving

Membrane Switch Function

OSD Conf guration Page

Image:

for the brightness, contrast, color temp, red, green, and blue

Geometry:

for the auto adjust, H position, V position, phase and clock

Video:

for the colour, tint, sharpness, noise reduction, DCDi and TV Setup

Audio:

for volume, bass, treble, balance, AVL and mute

Misc:

for the language, OSD position, graphic mode, ratio, reset and timer

LCD OSD Menu

Page 11 -- ML24V02A -- www.EclipseRackmount.com

< 3.1 > Options : DC Power

Model 12V 24V 48V

Input rating

Input voltage: 12-Volt 24-Volt 48-Volt

Input range: 9 ~ 18V 18 ~ 36V 36 ~ 75V

Input current

- No load 50 mA 50 mA 50 mA

- Full load 4950 mA 2450 mA 1220 mA

Output rating

Output voltage: 12-Volt 12-Volt 12-Volt

Output current: 4.16A 4.16A 4.16A

Efficiency 84% 85% 85%

< Part 3 >

Option excludes 1 x power cord and 1 x AC power adapter

***

Page 12 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

< 4.1 > QD Connection

< Part 4 > Quad Display Connection & Operation

1. VCR in :

This BNC connector is connected to video output from VCR/DVR. A pre-recorded quad screen signal from a tape can be

played back through a VCR/DVR and displayed on the video output channels. Push the VCR button (#2) to switch the

device to VCR Playback mode.

2. VCR out :

This BNC connector is to be connected to the Video in from your VCR/DVR. It will only provide a quad screen video to

ensure an un-interrupted video recording for all four cameras. The display video is not affected by the control panel.

3. Terminations :

These impedance switches are used to provide proper termination for each camera input. These switches toggle be-

tween 75Ω and Hi-Z impedance. Incorrect termination will degrade the quality of the video signal. All video inputs not

“looped through” to another device, the corresponding switches need to be set to 75Ω termination position. If another

device is connected to video out loop through connector set the corresponding termination switch to Hi-Z position. Any

device connected to the video out loop through connectors needs to be conﬁ gure to 75Ω video termination. The factory

default termination setting is 75Ω.

4. Ch1 In, Ch2 In, Ch3 In, and Ch4 In Video IN connectors :

These BNC connectors are used to connect to the video out from camera. Four cameras can be connected to these con-

nectors to form a quad screen in the following mapping order.

5. Ch1 Out, Ch2 Out, Ch3 Out, and Ch4 Out Video Loop through connectors :

These connectors are used to loop video signals from each camera out to other devices.

Page 13 -- ML24V02A -- www.EclipseRackmount.com

< 4.2 > QD ALARM Connection & Operation

1. ALARM I/O :

This female type 9 pin D-sub connector is used for alarm sensor input and alarm output control connections. It provides

Normal Open and Normal Close contacts for alarm out control.

The Alarm Hold Time can be conﬁ gured from 0 second to 99 minutes through system Setup menu.

2. VCR Connection for Tape Recording Start and Stop Control :

Connecting the contacts of VCR RECORD and STOP switch to the alarm output NC and NO contacts will allow you to use

an ordinary VCR to record for longer period of time. Combined with alarm sensor detection, the VCR will record only when

an alarm sensor is activated.

*. If more than one sensor have been trigged, VCR will start to record after the last trigged event.

*. In order to make use of the alarm called full screen display function, the VIDEO IN connector from the VCR has to be

connected to LIVE monitor connector of the device. If more than one sensor are trigged, VCR will then record all the

events in full screen mode accordingly.

Pin Assignment for Alarm Connector (female type)

PIN# PIN# PIN#

1 Sensor 1 4 Sensor 4 7 Normal Open Contact

2 Sensor 2 5 Reset In 8 Common Contact

3 Sensor 3 6 GND 9 Normal Close Contact

Page 14 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

< 4.2 > QD ALARM Connection & Operation

3 Sensor Activated Alarm

The unit is equipped with 4 alarm sensor inputs. If any alarm is activated:

■ the built-in buzzer and the alarm output control relay contact will be activated.

■ the quad will switch the corresponding channel indicator LED to blinking mode.

■ a warning message depending on different models will be displayed as follows:

Quad output channel (#4) LIVE output channel (#5)

Blinking Alarm & Title message on the

activated channel in quad screen

Full screen display of the activated channel.

Also display a blinking Alarm message

Alarm

Above mentioned alarm can be cleared by any of the following: 1. Connecting the Alarm Reset In contact, pin #5, of the

female type 9 pin D-sub connector (#8) to GND. 2. The Alarm Duration time elapses. 3. If the device is operated under

Security Lock ON mode, Push Lock button for 2 seconds to disable the function then push any button in the front panel.

4 Video Loss Alarm

Loss of video at any input is automatically detected by the device. The device will:

■ Activate the built-in buzzer.

■ Switch the corresponding channel indicator LED to blinking mode.

■ Display warning message on quad screen:

Quad output channel (#4)

Blinking Video Loss & Title message

on the activated channel in quad

screen

Video loss

■ The warning message and the buzzer can be cleared

by pushing Lock button (#2) for more than 4 seconds if the

device is operated under Security lock On mode, or pushing

any button on the front panel if the device is operated under

Security lock OFF mode.

Page 15 -- ML24V02A -- www.EclipseRackmount.com

hi-z

1 2 3 4

75

IN

OUT

RS-232

ALARM

dc 12V, 1amp

monitor vcrI/O

RS-232 Cable Wire

Computer

Remote Keypad

Rear Panel

< 4.3 > QD Remote Control Connection & Operation

Page 16 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

The device can be controlled via the male type 9 pin D-sub/RS-232 connector to a computer using ASCII code.

1. Pin assignment of the male type 9 pin D-sub connector:

When a computer is used to control this device through a RS-232 port, pin 6, 7, 8, and 9 must be disconnected to

prevent connecting the VCC and GND signals from the device to the computer. A RS-232 port only uses pin 1, 2,

and 3 for control signal transmission.

2. A terminal or computer can be connected to the male type 9 pin D-sub connector on the real panel from it RS-

232 port to control this device using standard, uppercase ASCII codes.

2.1 The ASCII command codes for the quad are listed in the table below. The transmission protocol is 1200-

baud rate, 8 data bit, 1 start bit, 1 stop bit, and no parity.

Pin Assignment for Remote Control Connector

1 GND 4 NC 7 VCC

2 RX 5 NC 8 GND

3 TX 6 VCC 9 GND

1 2 3 4 5

6 7 8 9

Function ASCII Command Code

Quad Screen Display E

CH 1 A

CH 2 B

CH 3 C

CH 4 D

Freeze *1 EA, EB, EC, ED

Auto Switching Sequence F

VCR/Live G

Key Lock *2 H

Setup Menu *3 GH

Text Select Down *4 (GH) A

Text Select Up (GH) B

Cursor Left (GH) C

Cursor Right (GH) D

Alarm Reset I

< 4.3 > QD Remote Control Connection & Operation

Page 17 -- ML24V02A -- www.EclipseRackmount.com

< 4.3 > QD Remote Control Connection & Operation

*1. In order to control the device to operate in Zoom mode, the computer has to ﬁ rst send

command code ” to switch the signal source from camera to VCR/DVR, at this time the device will

automatically zoom channel 1 video from VCR/DVR to full screen. User can then input a correspond-

ing channel code to zoom any other speciﬁ c channel. Input the corresponding channel code again to

put the speciﬁ c channel to freeze mode and send the code again to clear the freeze mode.

Example: Input GE, (GE) B, (GE) C, and (GE) D for zooming the video signal in channel 1 to 4 from

VCR/DVR. Input “A”, “B”, “C”, “D” again to freeze the speciﬁ c channel. Send command code “G”

again to get back to Live input mode.

*2. Computer has to send out command code “H” continuously for 2 seconds to switch the device be-

tween security lock ON and OFF mode. If any alarm is activated under security lock ON mode, the

device has to send out command code “H” continuously for more than 4 seconds to clear the alarm.

*3. Setup menu is switched ON by sending VCR/DVR and Lock button codes together.

*4. Text Select and Cursor Control functions can be performed only under menu Setup mode.

2.2 Right after computer/terminal has sent out the above mentioned control command code to the device, the

device will respond with following status code back to computer through RS-232 port:

Status

Code

Quad Status Status

Code

Quad Status

EF Device in Quad mode DE CH1 in Sequence mode

EE CH1 in Freeze mode DD CH2 in Sequence mode

ED CH2 in Freeze mode DB CH3 in Sequence mode

EC CH1 & 2 in Freeze mode D7 CH4 in Sequence mode

EB CH3 in Freeze mode CF Quad display in Sequence mode

EA CH1 & 3 in Freeze mode

E9 CH2 & 3 in Freeze mode E CH1 in Full screen mode

E8 CH1, 2, & 3 in Freeze mode D CH2 in Full screen mode

E7 CH4 in Freeze mode B CH3 in Full screen mode

E6 CH1 & 4 in Freeze mode 7 CH4 in Full screen mode

E5 CH2 & 4 in Freeze mode

E4 CH1, 2 & 4 in Freeze mode Attach to above code

E3 CH3 & 4 in Freeze mode XX-DF Buzzer/VCR ON

E2 CH1, 3, & 4 in Freeze mode XX-7F Security lock ON

E1 CH2, 3, & 4 in Freeze mode XX-3F Buzzer & Security lock ON (Stop)

E0 CH1, 2,3, & 4 in Freeze mode

Page 18 -- ML24V02A -- www.EclipseRackmount.com

2.3 The conﬁ guration of the status code for both normal and alarm operations:

There are total 2 bytes of the status codes. Byte one, the ﬁ rst 8 bits, shows the current status of the operation

modes that the unit is in. Byte two, the second 8 bits, shows the current status of the alarm operations of the

unit.

BYTE 1: Status code for normal operation modes

Channel Select

1110 = CH1

1101 = CH2

1011 = CH3

0111 = CH4

Display Mode

0 = Quad screen display

1 = Full Screen display

Auto-sequencing mode

0 = Auto sequencing mode

1 = Quad or full screen mode

VCR mode

0 = VCR operation

1 = Live operation

Security Lock mode

0 = Security lock ON mode

1 = Security lock OFF mode

Menu Setup mode

00 = Menu setup mode

BYTE 1 BYTE 2

}

START STOP START STOP

b7 b6 b5 b4 b3 b2 b1 b0

LOCK VCR SEQU QUAD CH4 CH3 CH2 CH1

< 4.3 > QD Remote Control Connection & Operation

MD-19QD

Page 19 -- ML24V02A -- www.EclipseRackmount.com

Sensor activated Alarm

0001 = CH1 activated

0010 = CH2 activated

0100 = CH3 activated

1000 = CH4 activated

Video Loss Alarm

0001 = CH1 activated

0010 = CH2 activated

0100 = CH3 activated

1000 = CH4 activated

BYTE 2: Status code for alarm operations: The ﬁ rst 4 bits show the sensor activated alarm status of each

channel; next 4 bits show the video loss alarm status of each channel. The digit “1” means alarm event is

detected, and “0” means no alarm event is detected.

b7 b6 b5 b4 b3 b2 b1 b0

CH4 CH3 CH2 CH1 CH4 CH3 CH2 CH1

b7 - b4: Sensor Activated Alarm b3 - b0: Video Loss Alarm

< 4.3 > QD Remote Control Connection & Operation

Page 20 -- ML24V02A -- www.EclipseRackmount.com

MD-19QD

5

4

2

VCR

button (#2)

Quad

button (#4)

CH Select

button (#5)

Function

ON ON OFF Display quad video signal from VCR tape

ON OFF Push Once Call up speciﬁ c quadrant from tape in full screen mode

ON OFF Push Twice Freeze speciﬁ c quadrant from tape in full screen mode

OFF X X Exit VCR operation and back to normal operation mode

3

SEQ.: Push this button to enable full page auto sequencing mode. Push this button again to disable it.

VCR: Push this button to enter into VCR Playback/Zoom operation. In this mode, the output video is displaying the

video signal from VCR. When operated in Full Screen display mode, push select buttons (#5) to zoom any speciﬁ c

camera signal pre-recorded on the tape in quad format. Push the select button (#5) again to freeze the expanded

picture on the screen.

Setup buttons (#1, #2) Function

CH Select buttons (#5)

UP, DOWN < , >

Push once Page 1 menu for time / date / title programming Text Selection Cursor Control

Push twice Page 2 menu for alarm conﬁ guration Text Selection Cursor Control

Push the third time Save the settings Yes / No

Push the fourth time Exit setup mode, back to normal

#1, #2 Setup buttons: Push these two buttons simultaneously to get into Menu Setup mode and display page 1 of

system setup menu. Push these two buttons simultaneously again to display page 2 of the setup menu. Use page 1

to program time/date and camera title and page 2 to conﬁ gure alarm operations. Under menu setup mode, Channel

Select buttons (#5) are used for cursor control and text selection to program the setup menu. Push the setup but-

tons simultaneously again to save the setting. Push the setup buttons fourth time to get back to ordinary operation

mode.

: Push this button to switch between Quad/ Full Screen display mode.

buttons: When operated in Quad mode, these buttons are used to freeze any speciﬁ c camera

by pushing the corresponding button. When operated in Full Screen display mode, these buttons are used to select

speciﬁ c camera to be displayed in full screen.

Quad button (#4) Channel Select buttons (#5) Function

ON ON Freeze speciﬁ c camera video in Quad screen mode

OFF ON Call up speciﬁ c camera video in full screen mode

These buttons are also used as cursor control and text select keys under Setup menu mode.

4

2

1

3

5

Lock: Security locks out button. Push this button for 2 seconds to enable control panel lock out function. Push this

button again for 2 seconds to disable the function.

1

Setup

VCR

SEQ

<

< >

Quad Display Control

< 4.4 > QD OSD Operation

Page is loading ...

CyberView MD-19QD User manual

This manual is also suitable for

CyberView MD-19QD User manual

Related papers

Other documents