SAVE THESE INSTALLATION INSTRUCTIONS FOR FUTURE REFERENCE
AND IN THE EVENT YOU NEED TO ORDER A REPLACEMENT PART
.
RECORD THE MODEL
#___________________
FROM THE PRODUCT LABEL ON THE PACKAGE
Unpacking: Care should be taken when you unpack your Bath Cabinet. Place the Door in a safe location to avoid
possibly chipping or cracking the mirror.
3026 / 3626
SURFACE MOUNTED
CABINET SHOWN
A - Safety glasses.
B - Measuring tape.
C - Level.
D - Power screwdriver or phillips hd
screwdriver.
E - A #2 phillips head screwdriver.
F - Electric Drill (Surface Mounting).
G - Drill Bit, 3/16” (Surface Mounting).
Bath Cabinet
Model No.
3026
3626
4826
3030
3630
Cabinet’s
Overall Size
W H D
30 26 5
36 26 5
48 26 5
30 30 5
36 30 5
Rough Wall Opening
for Recess Mounting
W H D
29 3/8 25 1/4 3 7/8
35 3/8 25 1/4 3 7/8
47 3/8 25 1/4 3 7/8
29 3/8 29 1/4 3 7/8
35 3/8 29 1/4 3 7/8
SPECIFICATIONS TABULATION
Cleaning: Use a household liquid glass cleaner to keep mirror and glass surfaces bright and clean. Do not spray cleaner
directly on mirrors and never use abrasive cleaners or any containing ammonia. This may cause Mirror damage.
K5006-0303 (PK06190)
Installation
Instructions
Bath Cabinets
Dual Compartment
Carefully read the Installation Instructions BEFORE you start. This allows you to become familiar with the installation
sequences and the required tools.
Tools Required: For installation of your Bath Cabinet, you will need the following tools;
IF YOU NEED REPLACEMENT PARTS, OR HAVE INSTALLATION QUESTIONS,
PLEASE CALL OUR
CUSTOMER SERVICE REPRESENTATIVES AT
800-355-5397
MONDAY - FRIDAY 8:30am - 4:00pm EASTERN TIME.
OR ONLINE AT www.cabinet-help.com
16
3
4
20
1
10
11
9
12
14
20
2
10
19
876
15
13
13
17
18
13
5
22
21
23
*
* - Parts designated are used for Surface Mount Installation only.
3026 / 3626
SURFACE MOUNTED
CABINET SHOWN
Item Part Description Qty.
No.
*1 Bottom Bracket 1
*2 Top Bracket 2
*3 Side Mirror 2
*4 Side Mirror Bracket 4
5 Door (large) 1
6 Door (small) 1
7 Hinges 4
8 #6 x 3/8” lg Flat Hd Screw 8
*9 #6 x 3/8” long Screw 4
10 #10 x 1 1/4” long Screw 5
11 Clear Washer 4
12 Snap Cap 4
13 Shelf Clip 20
14 Hole Plug 52
15 Shelf Tape Pads (12 per pack) 2
*16 Mirror Tape Pads (4 per pack) 2
17 Flange Bumper (If Required) 1
18 Glass Shelves (large) 2
19 Glass Shelves (small) 3
*20 Wall Anchor 5
21 Hinge Plates 4
22 #6 x 1/4” lg Flat Hd Screw 8
23 Cabinet Box 1
IF REQUIRED
If you have missing parts, do not return this item to the store, call us toll
free for an immediate, courteous response.
When ordering replacement parts,
please specify the Model Number,
Item Number & Part Description
To help identify the proper parts, please refer to the back page for
Illustrations of Parts. Assembly hardware is shown at actual size for ease
of identification.
Additional Screws and Wall Anchors are included in the
hardware bags for your convenience.
16
4
1112 9
20
1
2
10
23
1201
10
Please note, before installation, you must determine which side of the
Cabinet Box the small compartment will be on. To reverse the small
compartment, turn the Cabinet Box upside down.
Our sketches show the small compartment on the left.
Install the Top Bracket by inserting the “ball” / rounded end into the
Cabinet Box’s rear top slot. Slide a Top Bracket to the left and one to
the right. Lift the Cabinet Box onto the Bottom Bracket. Be certain that
the slot on the bottom of the Cabinet Box fits onto the Bottom Bracket.
Secure the Cabinet Box to the wall by using two #10 x 1 1/4” long
Screws through the Top Brackets.
Please note, if wall studs are not located at the Top Bracket holes, Wall
Anchors must be used. When using Wall Anchors, drill a 3/16” diameter
hole at the mounting screw location. Insert Wall Anchor into hole, a
slight tapping may be required for installation.
The Wall Anchor supplied is designed to be inserted in drywall / sheet
rock / gypsum board only.
Please note, the Cabinet Box must be level and plumb for the Doors to
work properly. Under certain conditions, the wall surfaces may not be
plumb, which will result in a slight gap, either at the top or bottom,
between the Doors and Door Bumpers.
LEVEL
SURFACE MOUNT INSTALLATION
FOR INSTALLING A SURFACE MOUNT BATH CABINET, FOLLOW STEPS 1, 2, 3, 6, 7 & 8.
SIDE VIEW
1.0”
SIDE VIEW
Attach the Side Mirror Brackets with #6 x 3/8” long Screws and
Clear Plastic Washers. Apply Mirror Tape Pads to Side Mirror
Brackets as shown.
Please note, do not remove the protective backing from the
Mirror Tape Pads or install the Side Mirror at this time. This will
be completed in the final Step, after the Doors have been
installed.
After all screws and Clear Plastic Washers are in place, install
the Snap Caps to cover the screw heads.
TO COMPLETE THE INSTALLATION OF A
SURFACE MOUNT BATH CABINET,
PROCEED TO STEPS 6, 7 & 8.
2
SURFACE
MOUNT
1
SURFACE
MOUNT
3
SURFACE
MOUNT
SKETCH SHOWS THE
SMALL COMPARTMENT
ON THE LEFT
WARNING: SAFETY GLASSES SHOULD BE WORN AT ALL TIMES.
Before you start, close the sink drain. This will avoid dropped parts from
falling into the drain.
Level and attach Bottom Bracket to wall with three #10 x 1 1/4” long
Screws. The Bottom Bracket is centered in the Cabinet Box’s mounted
location, but adjust slightly to the right or left, to make certain that at
least one of the three screws will engage a wall stud.
Height of Bottom Bracket should be a minimum 1” above faucet.
Please note, where wall studs are not located, Wall Anchors must be
used. When using Wall Anchors, drill a 3/16” diameter hole at the
mounting screw location. Insert Wall Anchor into hole, a slight tapping
may be required for installation.
The Wall Anchor supplied is designed to be inserted in drywall / sheet
rock / gypsum board only.
ACTUAL SIZE, #10 X 1 1/4” LONG SCREW
10
ACTUAL SIZE
#6 X 3/8” LONG SCREW
9
11
12
10
Please note, before installation, you must determine which side of the
Cabinet Box the small compartment will be on. To reverse the small com-
partment, turn the Cabinet Box upside down.
Our sketches show the small compartment on the left.
Position the Cabinet Box in the rough wall opening. Make certain that the
Cabinet Box flange covers the wall opening uniformly. Fasten both sides
of the Cabinet Box using four #10 X 1 1/4” long Screws and Clear Plastic
Washers. Do not over tighten Screws.
Please note, the Cabinet Box must be level and plumb for the Doors to
work properly.
After all screws and Clear Plastic Washers are in place, install the Snap
Caps to cover the screw heads.
TO COMPLETE THE INSTALLATION OF A RECESS
MOUNT BATH CABINET, PROCEED TO STEPS 6, 7 & 8.
H
W
WARNING: SAFETY GLASSES SHOULD BE WORN AT ALL TIMES.
Before you start, close the sink drain. This will avoid dropped parts from
falling into the drain.
Prepare an opening in the wall for the Cabinet Box. Refer to the
SPECIFICATIONS TABULATION on the front page for rough wall
opening dimensions.
Be certain that there is support on both sides of the opening to attach
the Cabinet Box. Opening height should be a minimum 1” above faucet.
3 7/8”
1.0”
SIDE VIEW
RECESS MOUNT INSTALLATION
FOR INSTALLING A RECESS MOUNT BATH CABINET, FOLLOW STEPS 4, 5, 6, 7 & 8.
THE FOLLOWING STEPS WILL BE USED FOR BOTH THE SURFACE MOUNT AND RECESSED MOUNT INSTALLATION
4
RECESS
MOUNT
5
RECESS
MOUNT
6
SKETCH SHOWS THE
SMALL COMPARTMENT
ON THE LEFT
Carefully remove the foam end caps from the Door.
Please note, when protective foam end caps are removed,
handle the Door with care. Make certain that the Door is not
placed on a hard surface, that may chip or crack the Mirror.
Use the foam end caps to protect the Door’s mirror while installing
the Hinges. Place them beneath the mirror as shown.
Install the Hinges in the mounting holes on the back of the Door,
as shown. Use the #6 x 3/8” long flat head Screws, supplied in the
Hinge Parts Bag and install with a #2 phillips head screwdriver.
Applying firm pressure, carefully install into the pre-drilled holes,
fastening the Hinges to the Door.
Do not Over Tighten.
Do not install with a power screwdriver.
7
8
PROTECTIVE FOAM END CAPS
ACTUAL SIZE, #10 X 1 1/4” LONG SCREW
10
ACTUAL SIZE
#6
X 3/8” LONG SCREW
8
DO NOT INSTALL WITH A
POWER SCREWDRIVER
6
17
7
If your Bath Cabinet’s Doors have a Door Bumper installed along the top and
bottom edges of the Door, disregard the Flange Bumpers. Otherwise,
install Door Bumpers at the top & bottom corners of the Cabinet Box frame,
centered in the flange.
3026 / 3626
SURFACE MOUNTED
CABINET SHOWN
22
21
22
21
22
21
17
NOTE FOR THE 4826 SERIES
SKETCH SHOWS THE
SMALL COMPARTMENT
ON THE LEFT
4826 SERIES
ACTUAL SIZE
#6
X 1/4” LONG SCREW
22
DO NOT INSTALL WITH A
POWER SCREWDRIVER
4826 S
ERIES
An additional set of Hinge Plates may need to be installed on the
Center Support, as shown in the sketch to the left.
The Hinge Plates may have been installed at the factory.
Please note, the Door for the small compartment has a mirror
bevel on all four sides. The two Doors for the large compart-
ment has a mirror bevel on three sides.
The CENTER DOOR is marked and should be installed first.
The 4826 Series has three doors. One for the small compartment and two for the large compartment.
ACTUAL SIZE
#6 X 1/4” LONG SCREW
22
DO NOT INSTALL WITH A
POWER SCREWDRIVER
INSTALL CENTER
DOOR FIRST
Install Hinge Plates to the Cabinet Box using two #6 x 1/4” long flat
head Screws.
Determine which Hinge Plate design is supplied with your Cabinet
Box, Center Mounting Screw, or Rear Mounted Screw.
Center Mounting
Screw Design
Rear Mounting
Screw Design
Mount the Hinge Plate, according to SKETCH 7A or
SKETCH 7B, at the set of threaded holes closest to
the top and bottom of the Cabinet Box. Do not tight-
en at this time, they should remain slightly loose until
the final Door adjustments have been made.
Please note, that the Cabinet Box must be level and plumb for the Door to
work properly. Under certain conditions, the wall surfaces may not be plumb,
which results in a slight gap, either at the top or bottom, between the Door
and Door Bumpers.
Mounting Screw
to be located in rear of
Hinge Plate
For Hinge Adjustment, Refer to
HINGE ADJUSTMENT INSTRUCTIONS
included in the Hinge Parts Bag
SKETCH 7A
CENTER
MOUNTING SCREW
SKETCH 7B
REAR
MOUNTING SCREW
Install Door Bumpers on the top & bottom flanges of the Cabinet Box frame,
located as shown.
IF REQUIRED
I
F REQUIRED
14
13
15
18
19
12 - Snap Cap 13 - Shelf Clip 14 - Hole Plug
1 - Bottom Bracket
Bracket
20 - Wall Anchor
2 - Top Bracket
21 - Hinge Plate
7 - Hinge
Pads
4 - Side Mirror
15 - Shelf Tape
6 - Mirror
Tape Pads
(If Required)
11 - Clear Washer
Refer to
Hinge Adjustment
Instructions
for details
Hinge Adjustment
Refer to
for details
Instructions
17 - Flange Bumpers
ILLUSTRATIONS OF PARTS
8
Determine the location of the Glass Shelves and install Shelf Clips. A
slight tapping may be necessary to insert into Cabinet Box holes.
Apply the Shelf Tape Pads to the top of the Shelf Clips and remove
the protective backing. Carefully install Glass Shelf. The front edge of
the Glass Shelf must be flush with the front of the Cabinet Box before
contacting the Shelf Tape Pads. A slight pressure should be applied
to the Glass Shelf, to be certain that contact has been made with all
four Shelf Tape Pads.
Insert Shelf Hole Plugs in the remaining holes.
FOR SURFACE
MOUNTED CABINET
ONLY
SURFACE MOUNTED
CABINET SHOWN
THE DOORS ARE NOT SHOWN
FOR CLARITY
For Surface Mount only: after the Doors have been installed and
properly adjusted, the Side Mirror will be attached. Remove the pro-
tective backing from the Mirror Tape Pads. When installing the Side
Mirror, be certain that it is centered and flush with the top & bottom
edge of the Cabinet Box. A slight pressure should be applied to the
Side Mirror to be certain that contact has been made with the Mirror
Tape Pads.
-
1
-
2
-
3
-
4
-
5
-
6
MAAX 105192-801-001-000 Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
MAAX 105192-801-001-000 Installation guide
-
-
-
-
-
-
-
-
-