Toro Commercial Walk-Behind Traction Unit, 18HP Pistol-Grip Hydro Drive User manual

Category
Lawnmowers
Type
User manual
FormNo.3376-415RevA
CommercialWalk-Behind
TractionUnit
18HPPistol-GripHydroDrive
ModelNo.30069—SerialNo.313000001andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3376-415*A
ThisproductcomplieswithallrelevantEuropeandirectives,
fordetailspleaseseetheseparateproductspecicDeclaration
ofConformity(DOC)sheet.
Introduction
Thisrotary-blade,lawnmowerisintendedtobeusedby
residentialhomeownersorprofessional,hiredoperators.Itis
designedprimarilyforcuttinggrassonwell-maintainedlawns
onresidentialorcommercialproperties.Itisnotdesignedfor
cuttingbrushorforagriculturaluses.
Readthisinformationcarefullytolearnhowtooperate
andmaintainyourproductproperlyandtoavoidinjury
andproductdamage.Thismanualshouldbeconsideredas
partofthemachine,asitcontains,safety,operationaland
maintenanceinformation.Themowerisaprecisionbuilt
machinedesignedsolelyforcuttinggrassandsimilarlowlying
groundvegetationwithinthelimitationsstatedinthismanual.
Youareresponsibleforoperatingtheproductproperlyand
safely.
YoumaycontactTorodirectlyforproductandaccessory
information,helpndingadealer,ortoregisteryour
productatToroCommercialProductsServiceDepartment
Spellbrook,BishopsStortford,CM234BU,England,
+44(0)1279603019,Email:uk.service@toro.com.
Wheneveryouneedservice,genuineToroparts,oradditional
information,contactanAuthorizedServiceDealerorToro
CustomerServiceandhavethemodelandserialnumbers
ofyourproductready.Figure1andFigure2identifythe
locationofthemodelandserialnumbersontheproduct.
Writethenumbersinthespaceprovided.
Figure1
1.Modelandserialnumberlocation
ModelNo.
SerialNo.
Figure2
1.Modelandserialnumberlocation
ModelNo.
SerialNo.
Thismanualidentiespotentialhazardsandhassafety
messagesidentiedbythesafetyalertsymbol(Figure3),
whichsignalsahazardthatmaycauseseriousinjuryordeath
ifyoudonotfollowtherecommendedprecautions.
Figure3
1.Safetyalertsymbol
Thismanualuses2otherwordstohighlightinformation.
Importantcallsattentiontospecialmechanicalinformation
andNoteemphasizesgeneralinformationworthyofspecial
attention.
©2013—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
2
Contactusatwww.Toro.com.
PrintedintheUSA.
AllRightsReserved
Contents
Introduction..................................................................2
Safety...........................................................................4
GeneralLawnMowerSafety.....................................4
SoundPressureforthe32RD,36RDand48
RD....................................................................6
SoundPowerforthe32RD,36RDand48
RD....................................................................6
VibrationLevelforthe32RD...................................6
VibrationLevelforthe36RD...................................6
VibrationLevelforthe48RD...................................6
SlopeIndicator.......................................................7
SafetyandInstructionalDecals.................................8
Setup...........................................................................10
1CheckingtheFluidsandTyrePressure.....................10
2ReadingtheManualandViewingtheOperator
TrainingMaterial................................................10
ProductOverview.........................................................11
Controls...............................................................11
Specications........................................................12
Attachments/Acessories.........................................12
Operation....................................................................12
AddingFuel...........................................................12
ThinkSafetyFirst...................................................13
OperatingtheParkingBrake....................................13
StartingandStoppingtheEngine..............................14
OperatingtheNeutralLocks....................................14
OperatingtheMowerBladeControlKnob
(PTO)...............................................................15
TheSafetyInterlockSystem.....................................15
DrivingtheMachineForwardandBackward..............16
BringingtheMachinetoNeutralPosition...................16
StoppingtheMachine.............................................17
PushingtheMachinebyHand..................................17
TransportingMachines............................................17
AdjustingtheHeight-of-Cut....................................17
AdjustingtheCasterPosition...................................18
AdjustingtheHandleHeight....................................19
HeightofCutChart................................................20
Maintenance.................................................................21
RecommendedMaintenanceSchedule(s)......................21
Lubrication...............................................................22
HowtoGrease.......................................................22
LubricatingtheCasterandWheelBearings.................22
GreasingtheMowerBeltIdler..................................22
GreasingthePumpControlandBellCrank................22
EngineMaintenance..................................................23
ServicingtheAirCleaner.........................................23
ServicingtheEngineOil..........................................24
ServicingtheSparkPlugs.........................................25
FuelSystemMaintenance...........................................26
ServicingtheFuelTank...........................................26
ServicingtheFuelFilter...........................................27
DriveSystemMaintenance.........................................27
AdjustingtheSpeedControlLinkage........................27
AdjustingtheNeutralControlLinkages.....................28
AdjustingtheHydroControlLinkages.......................29
AdjustingtheControlRod.......................................30
AdjustingtheTracking...........................................31
AdjustingtheSpringAnchorLinks...........................31
CheckingtheTyrePressure......................................32
CoolingSystemMaintenance......................................32
CleaningtheAirIntakeScreen..................................32
BrakeMaintenance....................................................33
ServicingtheBrake.................................................33
BeltMaintenance......................................................34
CheckingtheBelts..................................................34
ReplacingtheMowerBelt........................................34
AdjustingtheMowerBeltTension............................34
HydraulicSystemMaintenance....................................37
ServicingtheHydraulicSystem.................................37
MowerDeckMaintenance...........................................39
ServicingtheCuttingBlades.....................................39
AdjustingtheBladeBrake........................................41
Storage........................................................................42
Troubleshooting...........................................................43
Schematics...................................................................45
3
Safety
Improperlyusingormaintainingthismowercanresult
ininjury.Toreducethepotentialforinjury,complywith
thesesafetyinstructions.
Torodesignedandtestedthismowerforreasonablysafe
service;however,failuretocomplywiththefollowing
instructionsmayresultinpersonalinjury.
Toensuremaximumsafety,bestperformance,and
togainknowledgeoftheproduct,itisessentialthat
youandanyotheroperatorofthemowerreadand
understandthecontentsofthismanualbeforethe
engineiseverstarted.Payparticularattentiontothe
safetyalertsymbol(
Figure3)whichmeansCaution,
Warning,orDanger—“personalsafetyinstruction.”
Readandunderstandtheinstructionbecauseithasto
dowithsafety.Failuretocomplywiththeinstruction
mayresultinpersonalinjury.
GeneralLawnMowerSafety
ThefollowinginstructionshavebeenadaptedfromEN836.
Thiscuttingmachineiscapableofamputatinghandsandfeet
andthrowingobjects.Failuretoobservethefollowingsafety
instructionscouldresultinseriousinjuryordeath.
Training
Readtheinstructionscarefully.Befamiliarwiththe
controlsandtheproperuseoftheequipment.
Neverallowchildrenorpeopleunfamiliarwiththese
instructionstousethemower.Localregulationscan
restricttheageoftheoperator.
Keepinmindthattheoperatororuserisresponsiblefor
accidentsorhazardsoccurringtootherpeopleortheir
property.
Understandexplanationsforallpictogramsusedonthe
mowerorintheinstructions.
Gasoline
WARNING-Gasolineishighlyammable.Takethe
followingprecautions.
Storefuelincontainersspecicallydesignedforthis
purpose.
Refueloutdoorsonlyanddonotsmokewhilerefueling.
Addfuelbeforestartingtheengine.Neverremovethe
capofthefueltankoraddgasolinewhiletheengineis
runningorwhentheengineishot.
Ifgasolineisspilled,donotattempttostarttheengine
butmovethemowerawayfromtheareaofspillageand
avoidcreatinganysourceofignitionuntilgasolinevapors
havedissipated.
Replaceallfueltankandcontainercapssecurely.
Preparation
Whilemowing,alwayswearsubstantialfootwearandlong
trousers.Donotoperatetheequipmentwhenbarefoot
orwearingopensandals.
Thoroughlyinspecttheareawheretheequipmentisto
beusedandremoveallstones,sticks,wires,bonesand
otherforeignobjects.
Beforeusing,alwaysvisuallyinspecttoseethatguards,
andsafetydevices,suchasdeectorsareinplaceand
workingcorrectly.
Beforeusing,alwaysvisuallyinspecttoseethattheblades,
bladeboltsandcutterassemblyarenotwornordamaged.
Replacewornordamagedbladesandboltsinsetsto
preservebalance.
Starting
Disengageallbladeanddriveclutchesandplaceinto
neutralbeforestartingtheengine.
Donottiltmowerwhenstartingtheengineorswitching
onthemotor,unlessthemowerhastobetiltedfor
starting.Inthiscase,donottiltitmorethanabsolutely
necessaryandliftonlythepart,whichisawayfromthe
operator.
Starttheengineorswitchonthemotorcarefully
accordingtoinstructionsandwithfeetwellawayfrom
theblade(s).
Operation
Lightningcancausesevereinjuryordeath.Iflightning
isseenorthunderisheardinthearea,donotoperate
themachine;seekshelter.
Nevermowwhilepeople,especiallychildren,orpetsare
nearby.
Mowonlyindaylightoringoodarticiallight.
Avoidoperatingthelawnmowerinwetgrass,where
feasible.
Stayalertforholesintheterrainandotherhiddenhazards.
Neverdirectdischargeofmaterialtowardsbystanders.
Donotputhandsorfeetnearorunderrotatingparts.
Neverpickuporcarryalawnmowerwhiletheengineis
running.
Useextremecautionwhenreversingorpullinga
pedestriancontrolledlawnmowertowardsyou.
Walk,neverrun.
Slopes:
Donotmowexcessivelysteepslopes.
Exerciseextremecautionwhenonslopes.
Mowacrossthefaceofslopes,neverupanddown
andexerciseextremecautionwhenchangingdirection
onslopes.
4
Alwaysbesureofyourfootingonslopes.
Neveroperatethelawnmowerwithdamagedguards,or
withoutsafetydevices,forexampledeectorsand/or
grasscatchers,inplace.
Uselowthrottlesettingswhenengagingthe
traction-clutch,especiallyinhighgears.Reducespeed
onslopesandinsharpturnstopreventoverturningor
lossofcontrol.
Stopthebladeifthelawnmowerhastobetiltedfor
transportationwhencrossingsurfacesotherthangrass
andwhentransportingthelawnmowertoandfromthe
areatobemowed.
Donotoperatetheengineinaconnedspacewhere
dangerouscarbonmonoxidefumescancollect.
Stoptheengineandwhereakeyisttedremovethekey,
makesurethatallmovingpartshavecometoacomplete
stop:
wheneveryouleavethelawnmower.
beforerefueling.
beforeremovingthegrasscatcher.
beforemakingheightadjustmentunlessadjustment
canbemadefromtheoperator'sposition.
Stoptheengineandwhereakeyisttedremovethekey,
makesurethatallmovingpartshavecometoacomplete
stop,anddisconnectthesparkplugwire:
beforeclearingblockagesoruncloggingchute.
beforechecking,cleaningorworkingonthelawn
mower.
afterstrikingaforeignobject,inspectthelawnmower
fordamageandmakerepairsbeforerestartingand
operatingthelawnmower.
iflawnmowerstartstovibrateabnormally(check
immediately).
Reducethethrottlesettingduringengineshutdownand
,iftheengineisprovidedwithashut-offvalve,turnthe
fueloffattheconclusionofmowing.
Usecarewhenusingsulkies,and
useonlyapproveddrawbarhitchpoints.
limitloadstothoseyoucansafelycontrol.
donotturnsharply:usecarewhenreversing.
donotcarrypassengers.
Watchoutfortrafcwhencrossingornearroadways.
Beforeleavingtheoperator'sposition
disengagethepowertake-offandlowerthe
attachments.
placeintoneutralandsettheparkingbrake.
stoptheengineandremovethekey.
MaintenanceandStorage
Keepallnuts,boltsandscrewstighttobesurethe
equipmentisinsafeworkingcondition.
Donotusepressurecleaningequipmentonmachine.
Neverstoretheequipmentwithgasolineinthetankand
insideabuildingwherefumescanreachanopename
orspark.
Allowtheenginetocoolbeforestoringinanyenclosure.
Toreducetherehazard,keeptheengine,silencer,
batterycompartmentandgasolinestoragearefreeof
grass,leaves,orexcessivegrease.
Checkthedischargeguardfrequentlyandreplacewith
manufacturer'srecommendedparts,whennecessary.
Replacewornordamagedpartsforsafety.
Replacefaultysilencers.
Ifthefueltankhastobedrained,dothisout-doors.
Donotchangetheenginegovernorsettingsoroverspeed
theengine.Operatinganengineatexcessivespeedcan
increasethehazardofpersonalinjury.
Onmultibladedlawnmowers,takecareasrotatingone
blademaycauseotherstorotate.
Becarefulduringadjustmentofthelawnmowerto
prevententrapmentofthengersbetweenmovingblades
andxedpartsofthelawnmower.
Toensurethebestperformanceandsafety,
purchaseonlygenuineTororeplacementpartsand
accessories.Donotuse
will t
partsandaccessories;
theymaycauseasafetyhazard.
5
SoundPressureforthe32RD,
36RDand48RD
The32RDhasasoundpressurelevelattheoperator’searof
87dBA,whichincludesanUncertaintyValue(K)of2dBA.
The36RDhasasoundpressurelevelattheoperator’searof
87dBA,whichincludesanUncertaintyValue(K)of2dBA.
The48RDhasasoundpressurelevelattheoperator’searof
92dBA,whichincludesanUncertaintyValue(K)of2dBA.
Thesoundpressurelevelwasdeterminedaccordingtothe
proceduresoutlinedinEN836.
SoundPowerforthe32RD,36
RDand48RD
The32RDand36RDhasaguaranteedsoundpowerlevelof
100dBA,whichincludesanUncertaintyValue(K)of1dBA.
The48RDhasaguaranteedsoundpowerlevelof105dBA,
whichincludesanUncertaintyValue(K)of1dBA.
Thesoundpowerlevelwasdeterminedaccordingtothe
proceduresoutlinedinISO11094.
VibrationLevelforthe32RD
Hand-Arm
Measuredvibrationlevelforrighthand=1.2m/s
2
Measuredvibrationlevelforlefthand=2.0m/s
2
UncertaintyValue(K)=1.0m/s
2
Measuredvaluesweredeterminedaccordingtotheprocedures
outlinedinEN836.
VibrationLevelforthe36RD
Hand-Arm
Measuredvibrationlevelforrighthand=1.3m/s
2
Measuredvibrationlevelforlefthand=1.8m/s
2
UncertaintyValue(K)=1.0m/s
2
Measuredvaluesweredeterminedaccordingtotheprocedures
outlinedinEN836.
VibrationLevelforthe48RD
Hand-Arm
Measuredvibrationlevelforrighthand=2.5m/s
2
Measuredvibrationlevelforlefthand=3.1m/s
2
UncertaintyValue(K)=1.5m/s
2
Measuredvaluesweredeterminedaccordingtotheprocedures
outlinedinEN836.
6
SlopeIndicator
G01 1841
Figure4
Thispagemaybecopiedforpersonaluse.
1.Themaximumslopeyoucansafelyoperatethemachineonis20degrees.Usetheslopecharttodeterminethedegreeofslope
ofhillsbeforeoperating.Donotoperatethismachineonaslopegreaterthan20degrees.Foldalongtheappropriateline
tomatchtherecommendedslope.
2.Alignthisedgewithaverticalsurface,atree,building,fencepole,etc.
3.Exampleofhowtocompareslopewithfoldededge.
7
SafetyandInstructional
Decals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential
danger.Keepsafetysignsclearandvisible,replaceanydecalthatisdamagedorlost.
40-13–010
1.Cuttinghazardofhand
2.Cuttinghazardoffoot
95-5537
1.ReadtheOperator's
Manualforinstructionson
operatingthecuttingblade
3.Pullbacktodisengage
2.Pushforwardtoengage
105-4109
105-4110
106-2733
1.Fast
3.Slow
2.Continuousvariable
setting
106-5517
1.Warning—donottouchthehotsurface.
Manufacturer'sMark
1.Indicatesthebladeisidentiedasapartfromtheoriginal
machinemanufacturer.
8
115-1039
1.Parking
brake—disengaged
2.Parkingbrake—engaged
115-4212
1.Hydraulicoillevel3.Warning—donottouchthe
hotsurface.
2.ReadtheOperator's
Manual.
119-6672
1.Forward
10.Warning—readtheOperator'sManual.
2.Neutral11.Warning—donotoperatethismachineunlessyouaretrained.
3.Reverse
12.Thrownobjecthazard—keepdeectorinplace.
4.ToturnthemachinerightengageNeutralontherighthandle
whilethelefthandleisintheForwardposition.
13.Thrownobjecthazard—keepbystandersasafedistancefrom
themachine.
5.ToturnthemachineleftengageNeutralonthelefthandle
whiletherighthandleisintheForwardposition.
14.Warning—wearearprotection.
6.Fast15.Warning—stoptheengineandremovethesparkplugwire
beforeperforminganymaintenanceonthemachine.
7.Continuousvariablesetting16.Warning—stoptheenginebeforeleavingthemachine.
8.Slow17.Cutting,dismembermenthazardofhand—stayawayfrom
movingparts,keepallguardsandshieldsinplace.
9.Neutral
9
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
Checktheuidsandtyrepressure.
Operator'sManual
1
EngineOperator'sManual
1
Operatortrainingmaterial
1
2
Oildrainhose
1
ReadtheOperator'sManualandwatch
theoperatortrainingmaterialbefore
operatingthemachine.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
1
CheckingtheFluidsandTyre
Pressure
NoPartsRequired
Procedure
Beforeyoustarttheengineandusethemachine,check
theoillevelintheenginecrankcase;refertoChecking
theEngineOilLevel.
Checkthegreaseforthemowerandmowerdeck.
Checkthetyrepressure;refertoCheckingthetyre
Pressure.
Note:Thecuttingbladesaresettoa51mm(2inch)
height-of-cutatinitialpurchase.TheAxlepositionisB,with
2spacesbelowthecastersand4spacesbelowthespindle.
2
ReadingtheManualand
ViewingtheOperatorTraining
Material
Partsneededforthisprocedure:
1
Operator'sManual
1
EngineOperator'sManual
1
Operatortrainingmaterial
1
Oildrainhose
Procedure
ReadtheOperator'sManual.
Viewtheoperatortrainingmaterialbeforeoperatingthe
machine.TheDVDsuppliedisgeneraltrainingmaterial
andthemachinemaydifferfromthatsupplied.
Usetheoildrainhosewhenchangingtheengineoil.
10
ProductOverview
1
2
3
4
5
6
G016076
Figure5
1.Mowerdeck
4.Controls
2.Brake5.Handle
3.Gastank6.Casterwheel
Controls
Becomefamiliarwithallthecontrols(Figure6)beforeyou
starttheengineandoperatethemachine.
ThrottleControl
Thethrottlecontrolhastwopositions:FastandSlow.
OperatorPresenceControl(OPC)
Levers
WhenyousqueezetheOPCleversagainstthehandles,
theOPCsystemsensesthattheoperatorisinthenormal
operatingposition.WhenyoureleasetheOPClevers,the
OPCsystemsensesthattheoperatorhasleftthenormal
operatingposition,andthesystemwillstoptheengineif
eitherthespeedcontrolleverisnotintheneutralpositionor
thebladecontrol(PTO)knobisengaged.
BladeControlKnob(PTO)
Thebladecontrolknob(PTO)isusedtoengageand
disengagethedrivebelttodrivethemowerbladeswiththe
OPCleverspressedagainstthehandles.Pulltheknobupto
engagethebladesandpushdowntodisengagetheblades.
G016079
Figure6
1.Throttlecontrol
6.OperatorPresence
Controllevers(OPC)
2.Speedcontrollever
7.Handle
3.Ignitionswitch8.DriveLever
4.Choke9.Bladecontrolknob(PTO)
5.Neutrallock
10.Fuelshut-offvalve
IgnitionSwitch
Thisswitchisusedinconjunctionwithrecoilstarterandhas
threepositions:Off,RunandStart.
SpeedControlLever
Thismachinehasavariablespeedcontrolwithaneutral
position.Thiscontrolshowfastthemachinewilltravel.
DriveLevers
Releasedriveleverstoengageforwardtractionoperationand
squeezetheleversuntilanincreaseinforceisfelttogointo
neutralpositionandcontinuetosqueezetogoinreverse.
Squeezerighthanddrivelevertoturnrightandlefthandlever
toturnleft.
NeutralLock
Squeezedriveleversuntilanincreaseinforceisfeltandmove
lockstotherearforneutrallock.
FuelShut-offValve
Closethefuelshut-offvalvewhentransportingorstoring
mower.
11
Choke
Usethechoketostartacoldengine.
Specications
Note:Specicationsanddesignaresubjecttochange
withoutnotice.
32inchmowers:
Width
89cm(35inches)
Length
203cm(80inches)
Height
112cm(44inches)
Weight
231kg(509lb)
36inchmowers:
Width
94cm(37inches)
Length
203cm(80inches)
Height
44inches(112cm)
Weight
511lb(232kg)
48inchmowers:
Width
126cm(49-1/2inches)
Length
194cm(76-1/2inches)
Height
112cm(44inches)
Weight
248kg(547lb)
Attachments/Acessories
AselectionofToroapprovedattachmentsandaccessoriesare
availableforusewiththemachinetoenhanceandexpand
itscapabilities.ContactyourAuthorizedServiceDealer
orDistributorforalistofallapprovedattachmentsand
accessories.
Operation
AddingFuel
Forbestresults,useonlyclean,fresh,unleadedgasoline
withanoctaneratingof87orhigher((R+M)/2rating
method).
Oxygenatedfuelwithupto10%ethanolor15%MTBE
byvolumeisacceptable.
Donotuseethanolblendsofgasoline(suchasE15
orE85)withmorethan10%ethanolbyvolume.
Performanceproblemsand/orenginedamagemayresult
whichmaynotbecoveredunderwarranty.
Donotusegasolinecontainingmethanol.
Donotstorefueleitherinthefueltankorfuelcontainers
overthewinterunlessafuelstabilizerisused.
Donotaddoiltogasoline.
DANGER
Incertainconditions,gasolineisextremely
ammableandhighlyexplosive.Areorexplosion
fromgasolinecanburnyouandothersandcan
damageproperty.
Fillthefueltankoutdoors,inanopenarea,
whentheengineiscold.Wipeupanygasoline
thatspills.
Neverllthefueltankinsideanenclosedtrailer.
Donotllthefueltankcompletelyfull.Add
gasolinetothefueltankuntilthelevelis6to13
mm(1/4to1/2inch)belowthebottomofthe
llerneck.Thisemptyspaceinthetankallows
gasolinetoexpand.
Neversmokewhenhandlinggasoline,andstay
awayfromanopenameorwheregasoline
fumesmaybeignitedbyaspark.
Storegasolineinanapprovedcontainerand
keepitoutofthereachofchildren.Neverbuy
morethana30-daysupplyofgasoline.
Donotoperatewithoutentireexhaustsystemin
placeandinproperworkingcondition.
12
DANGER
Incertainconditionsduringfueling,static
electricitycanbereleasedcausingasparkwhich
canignitethegasolinevapors.Areorexplosion
fromgasolinecanburnyouandothersandcan
damageproperty.
Alwaysplacegasolinecontainersontheground
awayfromyourvehiclebeforelling.
Donotllgasolinecontainersinsideavehicleor
onatruckortrailerbedbecauseinteriorcarpets
orplastictruckbedlinersmayinsulatethe
containerandslowthelossofanystaticcharge.
Whenpractical,removegas-poweredequipment
fromthetruckortrailerandrefueltheequipment
withitswheelsontheground.
Ifthisisnotpossible,thenrefuelsuch
equipmentonatruckortrailerfromaportable
container,ratherthanfromagasolinedispenser
nozzle.
Ifagasolinedispensernozzlemustbeused,
keepthenozzleincontactwiththerimofthe
fueltankorcontaineropeningatalltimesuntil
fuelingiscomplete.
WARNING
Gasolineisharmfulorfatalifswallowed.Long-term
exposuretovaporscancauseseriousinjuryand
illness.
Avoidprolongedbreathingofvapors.
Keepfaceawayfromnozzleandgastankor
conditionerbottleopening.
Avoidcontactwithskin;washoffspillagewith
soapandwater.
UsingStabilizer/Conditioner
Useafuelstabilizer/conditionerinthemachinetoprovide
thefollowingbenets:
Keepsgasolinefreshduringstorageof90daysorless.
Forlongerstorageitisrecommendedthatthefueltank
bedrained.
Cleanstheenginewhileitruns
Eliminatesgum-likevarnishbuildupinthefuelsystem,
whichcauseshardstarting
Important:Donotusefueladditivescontaining
methanolorethanol.
Addthecorrectamountofgasstabilizer/conditionerto
thegas.
Note:Afuelstabilizer/conditionerismosteffective
whenmixedwithfreshgasoline.Tominimizethechance
ofvarnishdepositsinthefuelsystem,usefuelstabilizer
atalltimes.
FillingtheFuelTank
1.Shuttheengineoffandsettheparkingbrake.
2.Cleanaroundfueltankcapandremovethecap.Add
unleadedregulargasolinetofueltank,untilthelevelis
6to13mm(1/4to1/2inch)belowthebottomofthe
llerneck.Thisspaceinthetankallowsgasolineto
expand.Donotllthefueltankcompletelyfull.
3.Installfueltankcapsecurely.Wipeupanygasolinethat
mayhavespilled.
ThinkSafetyFirst
Carefullyreadallthesafetyinstructionsanddecalsinthe
safetysection.Knowingthisinformationcouldhelpyouor
anybystandersavoidinjury.
Theuseofprotectiveequipmentforeyes,hearing,feetand
headisrecommended.
CAUTION
Thismachineproducessoundlevelsinexcessof
85dBAattheoperator'searandcancausehearing
lossthroughextendedperiodsofexposure.
Wearhearingprotectionwhenoperatingthis
machine.
Figure7
1.Warning—wearhearingprotection.
OperatingtheParkingBrake
Alwayssettheparkingbrakewhenyoustopthemachineor
leaveitunattended.Beforeeachuse,checktheparkingbrake
forproperoperation.
Iftheparkingbrakedoesnotholdsecurely,adjustit.Referto
ServicingtheParkingBrake.
CAUTION
Childrenorbystandersmaybeinjuredifthey
moveorattempttooperatethemachinewhileitis
unattended.
Alwaysremovetheignitionkeyandsettheparking
brakewhenleavingthemachineunattended,even
ifjustforafewminutes.
13
SettingtheParkingBrake
Pulltheparkingbrakeleverrearward(Figure8).
G016075
1
Figure8
1.Parkingbrakelever(inthereleasedposition)
ReleasingtheParkingBrake
Pushtheparkingbrakeleverforward.
StartingandStoppingthe
Engine
StartingtheEngine
1.Connectthewirestothesparkplugs.
2.Openthefuelvalve.
3.Disengagethebladecontrolknob(PTO)andmovethe
speedcontrollevertoneutral.
4.Movethedriveleverstoneutralandsettheneutral
locks.
5.Settheparkingbrake.
6.Turntheignitionkeytotherunposition(
Figure6).
7.Tostartacoldengine,movethethrottlecontrol
midwaybetweenthefastandslowpositions.
8.Tostartawarmengine,movethethrottlecontrolto
thefastposition.
9.Pullthechokeknobiftheengineiscold(
Figure6).
Note:Awarmorhotengineusuallydoesnotrequire
anychoking.
10.Turntheignitionkeytothestartpositiontoenergize
thestarter.Whentheenginestarts,releasethekey.
Note:Donotengagethestarterformorethan5
secondsatatime.Iftheenginefailstostart,allow
fora15secondcool-downperiodbetweenattempts.
Failuretofollowtheseinstructionscanburnoutthe
startermotor.
11.Pushthechoketooffastheenginewarmsup
(
Figure9).
12.Iftheengineiscold,allowittowarmupandthen
movethethrottlecontroltothefastposition.
StoppingtheEngine
1.Movedriveleverstoneutralandsetneutrallocks.
2.Movethethrottlelevertoslow(Figure9).
3.Disengagethebladecontrolknob(PTO)andmovethe
speedcontrollevertoneutral.
4.Letengineidlefor30to60secondsbeforeturning
theengineoff.
5.Tostoptheengine,turntheignitionkeytooff.
G016077
Figure9
1.Throttlelever
3.Choke
2.Ignitionswitch
Important:Makesurefuelshutoffvalveisclosed
beforetransportingorstoringmachine,asfuel
leakagemayoccur.Beforestoringmachine,
removewirefromthesparkingplug(s)toprevent
possibilityofaccidentalstarting.
OperatingtheNeutralLocks
Alwayssettheneutrallockwhenyoustopthemachine.Set
theparkingbrakeifitisleftunattended.
SettingtheNeutralLock
1.Squeezethedriveleversbackuntilanincreaseinforce
isfelt.
2.Placethumbsontheupperpartofthelocksandmove
thembackuntilthepinsareintheneutralposition
(Figure10).
14
Figure10
1.Handle4.Drivelever
2.Neutrallock
5.Fullspeedforward
3.Neutralposition6.Reverseposition
ReleasingtheNeutralLock
1.Squeezethedriveleversbackuntilanincreaseinforce
isfelt.
2.Placethumbsontheupperpartoflocksandmove
themforwarduntilthepinsareintheforwardslot
(Figure11).
Figure11
1.Handle
4.Pininfullspeedforward
2.Neutrallock5.Handle
3.Drivelever6.Forwardslot
OperatingtheMowerBlade
ControlKnob(PTO)
Thebladecontrolknob(PTO)isusedinconjunctionwith
theOperatorPresenceControl(OPC)leverstoengageand
disengagethemowerblades.
EngagingtheMowerBlades(PTO)
1.Toengageblades,squeezetheOperatorPresence
Control(OPC)leversagainsthandlegrips(Figure12).
2.Pullbladecontrolknob(PTO)up.HoldtheOPC
leversagainsthandlegrip.
Note:ReleasingtheOPCleverswiththemower
bladesrunningwillkilltheengine.
3.Restarttheengineandrepeattheproceduretoengage
themowerbladesiftheoperatorpresencecontrol
(OPC)leversarereleased.
G0161 10
Figure12
1.Throttlelever4.DriveLever
2.OperatorPresence
Controllevers(OPC)
5.Bladecontrolknob(PTO)
3.Handle
DisengagingtheMowerBlades(PTO)
Themowerbladescanbedisengagedbyoneofthefollowing
steps.
1.Pushthebladecontrolknob(PTO)downtooff
(Figure12).
2.ReleasingtheOperatorPresenceControl(OPC)levers
willkilltheengineandstoptheblades(Figure12)with
thebladecontrolleverengaged.
TheSafetyInterlockSystem
CAUTION
Ifsafetyinterlockswitchesaredisconnectedor
damagedthemachinecouldoperateunexpectedly
causingpersonalinjury.
Donottamperwiththeinterlockswitches.
Checktheoperationoftheinterlockswitches
dailyandreplaceanydamagedswitchesbefore
operatingthemachine.
15
UnderstandingtheSafetyInterlock
System
Thesafetyinterlocksystemisdesignedtopreventthemower
fromstartingunless:
Thebladecontrolknob(PTO)ispushedoff.
Thespeedcontrolleverisinneutral.
Thesafetyinterlocksystemisdesignedtokilltheengine
when:
TheOperatorPresenceControl(OPC)leversarereleased
withthemowerengagedand/orthespeedcontrolisout
ofneutral.
Thespeedcontrolleverisshiftedoutofneutralwithout
holdingOPCleversorwiththebrakeengaged.
Thebladecontrolknob(PTO)ispulledupwithout
holdingtheOPClevers.
TestingtheSafetyInterlockSystem
ServiceInterval:Beforeeachuseordaily
Testthesafetyinterlocksystembeforeyouusethemachine
eachtime.Ifthesafetysystemdoesnotoperateasdescribed,
haveanAuthorizedServiceDealerrepairthesafetysystem
immediately.
WARNING
Whiletestingthesafetyinterlocksystem,the
machinemaymoveforwardandcausepersonal
injuryorpropertydamage.
Performthesafetyinterlocktestinanopenarea.
Ensurenooneisstandinginfrontofthe
machinewhileperformingthesafetyinterlock
test.
1.Settheneutrallocksandplacespeedcontrolleverin
neutral.
2.Starttheengine;refertoStartingandStoppingthe
Engine.
3.WithoutholdingtheOperatorPresenceControl(OPC)
levers,pullthebladecontrolknob(PTO)up.The
engineshouldkill.
4.Pushthebladecontrolknobdowntooff.
5.Withenginerunning,holddowntheOPClevers.
Pullthebladecontrolknob(PTO)up.Thedrivebelt
shouldengageandthemowerbladesbeginrotating.
6.ReleasetheOPClevers.Theengineshouldkill.
7.Withtheenginerunning,movethespeedcontrollever
forward.ReleasetheOPClevers.Theengineshould
kill.
8.Ifalltheaboveconditionsarenotmethavean
AuthorizedServiceDealerrepairthesafetysystem
immediately.
DrivingtheMachineForward
andBackward
Thethrottlecontrolregulatestheenginespeedasmeasured
inRPM(revolutionsperminute).Placethethrottlecontrolin
thefastpositionforbestmowingperformance.
DrivingForward
1.Releasetheparkingbrake.
2.Togoforward,movethespeedcontrollevertodesired
speed.
3.Releasetheneutrallock.RefertoReleasingtheNeutral
Lock.
4.Slowlyreleasethedriveleverstomoveforward
(Figure13).
Togostraight,releasedriveleversequally(Figure13).
Toturn,squeezethedriveleveronthesideand
directionyouwanttoturn(Figure13).
G0161 11
Figure13
1.Drivelever
2.Speedcontrollever
DrivingBackward
Slowlysqueezethedriveleverstothehandletomove
rearward(Figure13).
BringingtheMachineto
NeutralPosition
Alwayssettheneutrallockandparkingbrakewhenyoustop
themachine.
1.Squeezethedriveleverstoneutralposition.
2.Settheneutrallocks.RefertoOperatingNeutralLocks.
3.Movespeedcontrollevertoneutralposition.
16
StoppingtheMachine
1.Tostopthemachine,squeezethedriveleverstoneutral
positionandengageneutrallocks.
2.Movespeedcontrolleverintoneutral.
3.Stoptheengine;refertoStoppingtheEngine.
4.Waitforallmovingpartstostopbeforeleavingthe
operatingposition.Settheparkingbrake.
CAUTION
Childrenorbystandersmaybeinjuredifthey
moveorattempttooperatethemachinewhileitis
unattended.
Alwaysremovetheignitionkeyandsettheparking
brakewhenleavingthemachineunattended,even
ifjustforafewminutes.
PushingtheMachinebyHand
Theby-passvalvesallowthemachinetobepushedbyhand
withouttheenginerunning.
Important:Alwayspushthemachinebyhand.Never
towthemachinebecausehydraulicdamagemayoccur.
ToPushtheMachine
1.DisengagethePTO,movethemotioncontrolleversto
theneutrallockedpositionandsettheparkingbrake.
2.Opentheby-passvalvesbyturningthemcounter
clockwise1to2.Thisallowshydraulicuidtoby-pass
thepumpsandthewheelstoturn(Figure14).
3.Releasetheparkingbrake.
4.Pushthemachinetothedesiredlocation.
5.Settheparkingbrake.
6.Closetheby-passvalves,butdonotovertightenthem.
Note:Rotatetheby-passvalvesamaximumof2turns
sothevalvedoesnotcomeoutofthebodycausing
uidtorunout.
Important:Donotstartoroperatethemachine
withtheby-passvalvesopen.Damagetosystem
mayoccur.
Figure14
1.Hydraulicpump2.By-passvalve
TransportingMachines
Useaheavy-dutytrailerortrucktotransportthemachine.
Ensurethatthetrailerortruckhasallnecessarylightingand
markingasrequiredbylaw.Pleasecarefullyreadallthesafety
instructions.Knowingthisinformationcouldhelpyou,your
family,petsorbystandersavoidinjury.
Totransportthemachine:
Stoptheengine,removethekey,setthebrake,andclose
thefuelvalve.
Securelyfastenthemachinetothetrailerortruckwith
straps,chains,cable,orropes.
Secureatrailertotowingvehiclewithsafetychains.
AdjustingtheHeight-of-Cut
Thismachinehasa26to108mm(1to4-1/4inch)rangefor
height-of-cut.Adjustthebladespacers,rearaxleheightor
frontcasterspacerstogetthecorrectheight-of-cut.Usethe
Height-of-Cutcharttoselectthecombinationofadjustments
required
AdjustingtheBladeHeight
Adjustthebladesbyusingthe4spacers(1/4inch)spacers
onthebladespindlebolts.Thisallowsfora25mm(1inch)
adjustmentrangeofcuttingheight,in6mm(1/4inch)
increments,inanyaxleposition.Usethesamenumberof
bladespacersonallbladestoachievealevelcut(2aboveand
2below,1aboveand3below,etc.).
1.DisengagethePTOandpullthethrottletotheslow
position.
2.Turntheignitionswitchtooff.
3.Waitforallmovingpartstostopbeforeleavingthe
operatingposition.Settheparkingbrake.
4.Holdthebladeboltandremovethenut.Slidethebolt
downthroughthespindle,andchangethespacersas
needed(
Figure15).
17
Figure15
1.Blade
4.Spacer
2.Bladebolt5.Thinwasher
3.Curvedwasher
6.Nut
5.Installthebolt,curvedwasher,blade,addextra
spacers,andsecurethemwithathinwasherandanut
(Figure15).
6.Torquethebladeboltto101-108N-m(75-80ft.-lb.).
AdjustingtheAxleHeight
Adjusttheaxlepositiontotheselectedheight-of-cutsetting.
1.DisengagethePTOandpullthethrottletothestop
position.
2.Waitforallmovingpartstostopbeforeleavingthe
operatingpositionandthensettheparkingbrake.
3.Placeajackundertheengineframe.Raisethebackend
oftheengineframeupenoughtoremovethedrive
wheels.
4.Removethedrivewheels.
5.Loosen,butdonotremove,the2topaxlebolts
(
Figure16).
6.Removethe2loweraxlebolts(Figure16).
Figure16
1.Topaxlebolt2.Loweraxlebolt
7.Raiseorlowerthemountingbracket,sothatyoucan
installthe2axleadjustmentboltsinthedesiredhole
location(Figure16).Ataperedpunchcanbeusedto
helpaligntheholes.
8.Tightenall4bolts.
9.Installdrivewheelsandlowerthemower.
AdjustingtheCasterPosition
1.UsingtheHeight-of-CutChart,adjustthecaster
spacerstomatchwiththeaxleholeselected(Figure17).
Figure17
1.Latchpin
3.Spacer,13mm(1/2inch)
2.Spacer,5mm(3/16inch)
2.Removethelatchpin,slidethecasterfromthesupport,
andchangethespacers(Figure17).
3.Installthecasterinthesupportandinsertthelatchpin
(
Figure17).
18
AdjustingtheHandleHeight
Thehandlepositioncanbeadjustedtomatchtheoperator's
heightpreference.
1.Removethehairpincotterpinsandclevispinsfrom
thedriveleversandneutrallocks(Figure18).
Figure18
1.Controlrod5.Lefthandleshown
2.Clevispin
6.Neutrallock
3.Drivelever7.Hairpincotterpin
4.OperatorPresence
Controllever(OPC)
2.Loosentheupperangebolts(3/8x1-1/4inches)and
angenutsecuringhandletorearframe(Figure19).
3.Removethelowerangebolts(3/8x1inch)andange
nutssecuringhandletorearframe(Figure19).
4.Pivothandletodesiredoperatingpositionandinstall
lowerangebolts(3/8x1inch)andangenutsinto
mountingholes.Tightenallangebolts.
Figure19
1.Controlrodtting
6.Highposition
2.Lowermountingholes7.Lowerposition
3.Rearframe
8.Uppermountinghole
4.Lowerangebolt(3/8x1
inch)
9.Handle
5.Upperangebolt(3/8x
1-1/4inches)
10.Flangenut(3/8inch)
5.Adjustthecontrolrodlengthbyrotatingthecontrol
rodintherodtting(Figure18andFigure19).
6.Installhairpincotterbetweendriveleversandneutral
locksandintoclevispins(Figure18).
Note:Makesuretheclevispinsareinsertedintothe
neutrallocks.
7.Performthehydrauliclinkageadjustmentswhenthe
handleheightischanged;referHydraulicLinkage
Adjustments.
19
HeightofCutChart
Numberofspacers
belowcaster
Numberof6mm(1/4inch)bladespacersbelowspindle
AxlePosition
13mm(1/2
inch)
5mm(3/16
inch)
43210
A00
26mm(1
inch)
32mm
(1–1/4inch)
38mm
(1–1/2inch)
45mm
(1–3/4inch)
51mm(2
inch)
A01
29mm
(1–1/8inch)
35mm
(1–3/8inch)
41mm
(1–5/8inch)
48mm
(1–7/8inch)
54mm
(2–1/8inch)
A10
35mm
(1–3/8inch)
41mm
(1–5/8inch)
48mm
(1–7/8inch)
54mm
(2–1/8inch)
60mm
(2–3/8inch)
B01
35mm
(1–3/8inch)
41mm
(1–5/8inch)
48mm
(1–7/8inch)
54mm
(2–1/8inch)
60mm
(2–3/8inch)
B10
41mm
(1–5/8inch)
48mm
(1–7/8inch)
54mm
(2–1/8inch)
60mm
(2–3/8inch)
67mm
(2–5/8inch)
B11
45mm
(1–3/4inch)
51mm(2
inch)
57mm
(2–1/4inch)
64mm
(2–1/2inch)
70mm
(2–3/4inch)
B20
51mm(2
inch)
57mm
(2–1/4inch)
64mm
(2–1/2inch)
70mm
(2–3/4inch)
76mm(3
inch)
C
11
48mm
(1–7/8inch)
54mm
(2–1/8inch)
60mm
(2–3/8inch)
67mm
(2–5/8inch)
73mm
(2–7/8inch)
C
20
54mm
(2–1/8inch)
60mm
(2–3/8inch)
67mm
(2–5/8inch)
73mm
(2–7/8inch)
79mm
(3–1/8inch)
C
21
57mm
(2–1/4inch)
64mm
(2–1/2inch)
70mm
(2–3/4inch)
76mm(3
inch)
83mm
(3–1/4inch)
C
30
64mm
(2–1/2inch)
70mm
(2–3/4inch)
76mm(3
inch)
83mm
(3–1/4inch)
89mm
(3–1/2inch)
D21
60mm
(2–3/8inch)
67mm
(2–5/8inch)
73mm
(2–7/8inch)
79mm
(3–1/8inch)
86mm
(3–3/8inch)
D30
64mm
(2–1/2inch)
70mm
(2–3/4inch)
76mm(3
inch)
83mm
(3–1/4inch)
89mm
(3–1/2inch)
D31
70mm
(2–3/4inch)
76mm(3
inch)
83mm
(3–1/4inch)
89mm
(3–1/2inch)
95mm
(3–3/4inch)
D40
76mm(3
inch)
83mm
(3–1/4inch)
89mm
(3–1/2inch)
95mm
(3–3/4inch)
102mm(4
inch)
E31
73mm
(2–7/8inch)
79mm
(3–1/8inch)
86mm
(3–3/8inch)
92mm
(3–5/8inch
)
98mm
(3–7/8inch)
E40
79mm
(3–1/8inch)
86mm
(3–3/8inch)
92mm
(3–5/8inch
)
98mm
(3–7/8inch)
105mm
(4–1/8inch)
E41
83mm
(3–1/4inch)
89mm
(3–1/2inch)
95mm
(3–3/4inch)
102mm(4
inch)
108mm
(4–1/4inch)
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Toro Commercial Walk-Behind Traction Unit, 18HP Pistol-Grip Hydro Drive User manual

Category
Lawnmowers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI