DESCRIPTION
The Watt Stopper multi-button switch is low voltage and
compatible with The Watt Stopper Basic Contactor, LP8, Lighting
Integrator and ACP-NET lighting control panels, the ARP
Automatic Relay Pack, LC-100 Intelligent Power Pack, and
occupancy sensors with manual control capabilities. Any button
on the multi-button switch may be wired to any relay or group of
relays within a single panel or pack and to one or more sensors.
Each switch button is rated for 25mA@50VDC.
These instructions provide wiring diagrams for the multi-button
switch in each of the compatible systems. For system
documentation forms, operation and installation of the other
components in the system, refer to the installation instructions for
those components as well as the system operation manual.
The switch is available in four configurations as illustrated in the
Ordering Information section below.
INSTALLATION
The multi-button switch is made up of two primary parts: the cover plate and the back containing electrical
components and wire terminals.
Before starting, read all instructions. If you have any questions, call our Service Team at: 888-852-2778.
Removing the Screwless Cover Plate
1. Press the black tab at the bottom
edge of the plate.
2. Pull the plate away from the back.
3. Lift the plate up and off as shown.
To replace the cover plate, place the hang
bar at the top of the plate onto the hang
hook at the top of the switch base. Press
the bottom in place until it clicks.
Switch Button Labeling
The standard switch buttons provide space for 3/8” wide x 1 1/8” long (9mm x 30mm) label directories. The
labels can be attached by removing the clear lenses on the buttons, positioning the labels and replacing the
lenses. You can also completely remove the button from the base. It may be easier to align the label with the
button removed.
L1S/L3S/L5S/L9S
Multi-Button Switch
Installation Instructions
Santa Clara, CA 95050
888.852.2778
www.wattstopper.com
© 2003 The Watt Stopper,
®
Inc.
L1S
L3S
L5S
L9S
Gang Max
Model Description Standard Large Box Pilot
Buttons Button Size Load
L1S Single button switch 0 1* Single 10mA
L3S Three button switch 2* 1 Single 15mA
L5S Five button switch 4* 1 Single 25mA
L9S Nine button switch 8* 1 Double 45mA
* with pilot light
The suffix at the end of the model number indicates switch color:
-2 for ivory, -4 for almond, -7 for white, -9 for grey
ORDERING INFORMATION
Panel#
Switch#
Replacing the cover
Hang Bar Hang Hook
Panel Division: 888.852.2778
CAUTION
Power should
always be off
when wiring any
lighting control
devices.
For emergency
service or
support, call our
Service Team at:
888-852-2778.
MOUNTING AND WIRING
03724r1 12/2003
Pilot light
(one for each standard button)
(for each button)
(one per switch)
Switch input
Locator light
P(x)
S(x)
Loc
Common
(one per switch)
Com
The 1-, 3- and 5-button switches mount in a standard single-
gang box. The 9-button switch mounts in a double-gang
box. To employ all of the buttons on a switch, pull a cable
containing the number of conductors indicated below:
Buttons on switch . . . . 1 3 5 9
Conductors needed . . . 4 7 11 19
The switch can be wired in series or in parallel for multiple
location applications (3-way, 4-way, etc.). The signal and
pilot light terminations for the standard buttons are identified
from the top down with the signal termination for the large
button located directly above the common terminal.
Multi-Button Switch
ACP-NET
SWA SWB COM LIGHT
+24VDC
ON
OFF
LCB-308 Lighting Control Board
COM
1
LOC
S(x) P(x)
Multi-Button Switch
ARP
SW1A(2A)
OUT1(2)
24VDC
COM +24VDC
COM
1
LOC
S(x) P(x)
Configuration
DIP Switches
ON
OFF
6 7 8 9
1ms
1PB
2ms
2PB
Multi-Button Switch
Basic Contactor
INPUT
(x)
OVERRIDE
+24VDC
COM
1
LOC
2
S(x) P(x)
2
Multi-Button Switch
LI/LP/SWS
COM
1
LOC
S(x) P(x)
RELAY
TERMINALS
ACC.
POWER
White
24VAC
24R
Yelcom
W
Y
B
R
Multi-Button Switch
LC-100
ON OFF
+24VDC
COM
1
LOC
2
S(x) P(x)
2
Multi-Button Switch
Power Pack
COM
1
LOC
S(x) P(x)
Control Output +24VDC
Man. Switch
+24VDC Input
Common
Occupancy Sensor
BLACK
RED
BLUE
ACP-NET ConnectionsARP Connections
Basic Contactor Control Panel Connections
Lighting Integrator, LP8, SmartWired Switch Panel Connections
LC-100 Connections
Occupancy Sensor with Manual Switch Connections
Notes:
1 One common required per switch.
2 Locator and switch LEDs are unavailable
when connected to this system.
/
