All-Pro MS276RD Operating instructions

Brand: All-Pro

Model: MS276RD

Category: Work lights

Type: Operating instructions

This manual is also suitable for

MS276RDW

Instruction Manual/Instrucciones

Questions?/¿Preguntas? 1-800-334-6871 [email protected]

•Donotallowsensorheadtotouchlighthousing–maintainatleast1/2inchspacebetween

 xtureandsensor.

•Iflensisreplaced,useonlytemperedsafetyglassofequalthickness.

•Forproperoperationandprotectionagainstdamage;themotionsensorheadadjustment

 knobsmustbefacingtheground.

•Donotusethisapparatusnearwater.

•Cleanonlywithadrycloth.

•Donotblockanyventilationopenings.Installinaccordancewiththemanufacturer’sinstructions.

•Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stovesorother

 apparatus(includingampliers)thatproduceheat.

•Onlyuseattachments/accessoriesspeciedbythemanufacturer.

•ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwo

 conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust

 acceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

 UnderPart15oftheFCCRules,anychangesormodicationstothemotiondetector

 describedinthisinstructionsheetthatarenotexpresslyapprovedbyCooperLighting,LLC

 couldvoidtheuser’sauthoritytooperatetheequipment.

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

device,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonable

protectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,

usesandcanradiateradiofrequencyenergyandifnotinstalledandusedinaccordancewith

theinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereis

noguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoes

causeharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturning

theequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneor

moreofthefollowingmeasures:

 -Reorientorrelocatethereceivingantenna.

 -Increasetheseparationbetweentheequipmentandreceiver.

 -Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

  isconnected.

 -Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

WARNING: FCC Regulations state that any unauthorized changes or modiﬁcations to this

equipment not expressly approved by the manufacturer could void the user’s authorization

to operate this equipment.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

•Installthemotionsensor/transmitter8-12feetabove

 ground(motionsensorislesssensitiveabove12feet).

•Locatemotionsensorsomotionmoveslaterallyor

 towardsthedetectionzone(Fig.1).

•Locatesensorawayfromheatproducingsourcesto

 preventfalsetriggering.Alsobeverycarefulnotto

 includeobjectssuchaswindows,whitewallsand

 waterinthedetectionzone.

•Locatextureawayfrommovingobjectssuchas

 trees,largeshrubsandstreettrafc.

•Donotinstallmorethanonemotionactivatedoodlightononewallswitch.

PACKAGING CONTENTS/CONTENIDO DEL PAQUETE

ITEMS REQUIRED

(Purchase separately)

•Phillipsscrewdriver

•Outdoorweatherproofsiliconecaulking

•(2)100watt(MAX)PAR38oodlightbulbs

NOTE:Thisxturewasdesignedtoworkwithupto150wattmaximumPARhalogenoodbulbs.

Forimprovedenergyefciency,lowerwattagePARhalogenoodbulbsmaybeused.Compact

Fluorescent(CFL)bulbscontainelectronicswhichmayinterferewiththemotionsensingfunction

ofyourxtureandarenotrecommended.TomeetENERGYSTAR

®

requirements,maximumlamp

wattagecannotexceed250watts.

HOW IT WORKS

PIRdoesagoodjobofdetectinglateralmotionacrossthe270°

rangeofdetection.PrecisionPlusDopplerRadar™doesan

excellentjobdetectingmotiontowardsandawayfromtheunit.

Bothsystemscombinedprovideenhancedaccuracyandcomplete

coveragewithinthedetectionrange.Motionfromanydirectionwill

triggeryouroodlight—evenduringhotorcoldtemperatureextremes.

WARNINGS AND CAUTIONS

•Readtheseinstructions.

•Keeptheseinstructions.

•Heedallwarnings.

•Followallinstructions.

•Foroutdooruseonly.

•cULusLISTEDforwetlocations.

•Connectxturetoa120volt,60Hzpowersource.Anyotherconnectionvoidsthewarranty.

•Fixtureshouldbeinstalledbypersonswithexperienceinhouseholdwiringorbyaqualied

 electrician.Theelectricalsystem,andthemethodofelectricallyconnectingthexturetoit,

 mustbeinaccordancewiththeNationalElectricalCodeandlocalbuildingcodes.

•Alwaysreplacebulbwiththesamewattageorlowerwattagethanmarked.Installingabulb

 ofahigherwattagecouldcreatearehazard.Useofahigherwattagebulbwillvoidthe

 warranty.(Maximum150watthalogenbulb.)TomeetENERGYSTAR

requirements,

 maximumlampwattagecannotexceed250watts.

•Keepawayfromammableobjects.Donotpositionxturewithinoneinch

 ofanycombustiblematerials.

•BulbgetsHOTquickly!

•Thebulbandxturegetextremelyhotduringuse.Disconnectpowerandallow

 xturetocoolbeforechangingbulborhandlingxture.

•Disassemblyofyourxturewillvoidthewarranty.

•Yourxtureispre-wiredandpre-assembledforeasyinstallation.

•Minimum90°Csupplyconductors.

•Fixturemountstoarecessedorsurfacemountedstandardgroundedjunctionboxmarked

 foruseinwetlocations.

MS276RD (Bronze)

MS276RDW (White)

A. Motion detector and light ﬁxture

Detector de movimiento y

artefacto de luz

ENGLISH

Upto

90feet

270degrees

Fig.1

D. Coverplate gasket

Junta de la placa

de cubierta

C. (2) #6 and (2) #8 mounting screws

(use the size that ﬁts your junction box)

(2) Tornillos #6 y (2) tornillos #8 de montaje

(utilice el tamaño que mejor se adecue

a su caja de conexión)

I. (2) Lampholder gaskets

(2) Juntas para portalámpara

E. (3) Wire nuts

(3) Tuercas para

alambre

B. Mounting bracket

Soporte de montaje

F. Mounting plate screw

Tornillo para la placa

de montaje

G. Color-matched

center hole plug

Tapón para agujero

central de color

coincidente

H. (2) Light covers

(2) Cubiertas de las luces

•Ifthextureismountedhigher,theangleofthe

  sensorbelowhorizontalshouldincrease.

5. Walkthroughthedetectionzoneatthefarthestdistanceyouwantyourdetectorto

 detectmotion.

6. AdjusttheSENSITIVITYknobuntilyougetdesiredresults.Formorerange,aimsensor

 slightlyupward.Forlessrange,aimsensorheadslightlydownward.Lightswillturnoff

 4secondsaftermotionstops.

7. Adjustthe“Auto”MODEknobtoatimeselectionfrom1m-12m,dependingonhowmany

 minutesyouwantthexturetostayonaftermotionisdetected.Atdusk,thephotocontrol

 willactivateyourxturetooperateaccordingtothesettingschosen.

NOTE:DecreasingtheSENSITIVITYwilldecreasethedistancetheunitcandetect.

NOTE:Duringdaylighthours,theredLEDindicatorlightwillashwhenmotionisdetected.

Thisisnormal.

SELECTING YOUR DESIRED FEATURE

ENERGY STAR

TomeetENERGYSTAR

requirements,thephotosensorcontrolknobmustbeinthe“Auto”

modetopreventoperationduringfulldaylight.Maximumlampwattagecannotexceed250watts.

TROUBLESHOOTING

MOUNTING YOUR FIXTURE

NOTE:Universalcoverplatemountstorecessedor

surfacemountedstandardjunctionboxes(Fig.2).

Junctionboxmustbeatleast1-1/2˝indepthforproper

installationforrecessedmountapplication.

NOTE:Forbestperformancewheninstallingmorethan

onePrecisionPlusDopplerRadar™xture:

•Twoormoreunitsmountedsidebyside(facingthe

  samedirection)shouldbeatleast17feetapart.

 •Twounitsfacingeachothershouldbemountedat

  least100feetapart.

 •Fixturecanbewalloreavemounted(Fig.3).

WARNING: Risk of electric shock. Disconnect power

at fuse or circuit breaker before installing or servicing.

1. Lineuptheholesonthemountingbracket(B)with

theholesonyourjunctionbox.Usingeither(2)#6

screwsor(2)#8screws(C)(dependingonthesize

oftheholesinyourjunctionbox),attachthemounting

bracket(B)toyourjunctionbox(Fig.4).

2. Threadxturewiresthroughcoverplategasket(D).

3. Positionthegasket(D)onthecoverplateandconnect

theblackwirefromthexture(A)totheblackhouse

supplywireandthewhitewirefromthexture(A)

tothewhitesupplywireusingthewirenuts(E)

provided.Attachthegroundwirecomingfromyour

housetothecoppergroundwirefromthexture(A)

usingwirenut(E)provided.Ifnohousegroundwire

isavailable,attachthecoppergroundwirefrom

thexture(A)tothejunctionboxifitismetaland

grounded.Ifjunctionboxisnotmetalandnohouse

groundwireisavailable,analternativeground

sourcemustbeusedforsafeoperation(Fig.5).

4. Attachxture(A)tothemountingbracket(B)

usingthemountingplatescrew(F)provided.

Besurenoloosewiresremainstickingoutfrom

underneaththecoverplate.Insertplasticcolor-

matched(G)pluginmountingplatescrewhole

fornishedappearance(Fig.6).

5. Applysiliconecaulkingaroundedgesofcoverplateand

inanyopenholestoprovideawatertightsealfrom

rainandmoisture.

6. Installprotectivelampcovers(H)ontolampholders

byliningupthenipplesonthecovers(H),overthe

lampholderslots.Lockintoplacebytwistingcovers

counterclockwise(Fig.7).

7. Insertgaskets(I)intolampholdersandscrew

bulbsintoeachlampholder(Fig.8).(Donotover

tightenbulbs.)

8. Turnpoweronatmainfuse/breakerbox.

AIMING THE LIGHT

Loosentheknobonthesideofthelampholder.

Tiltlampholderupordowntodesiredposition,then

retightenknob.

WARNING: Deviation from the assembly instructions

may result in a risk of electric shock.

OPERATING YOUR FIXTURE

1. TurnthearrowontheMODEknobto“TEST”fortest

mode(Fig.9).

2. TurnthearrowontheSENSITIVITYknobtoamiddle

pointbetween“+”and“-”.

3. Turnonthepowertothexture(A).Allowxtureto

 warmupapproximately90secondsbeforetesting.

 (Lightsmayormaynotcomeonduringwarm-up

 period;thisisnormal.)

4. Aimsensortowardthegeneraldirectionthatmotion

willbecomingfrom.Maintainatleast1˝ofclearance

betweensensorheadandlamps.Alwaysposition

thesensorheadwithcontrolswitchesfacingtoward

theground.

NOTE: (Sensor Head Placement) Foroptimumdetection,

youmayhavetoexperimentwithaimingandsettings.

Eachlocationwillbedifferentandyourterrainmay

affecttheangleyoursensorneeds.Adjustingtheangle

willchangeyourareaofdetection.Herearesome

generalguidelinestohelpwithsetup:

•8´-12´abovethegroundisagoodrangeforthe

  placementofyourxture.

•Foran8´mountingheight,placingthesensorata

  5°anglebelowhorizontalshouldworkwellfor

  mostlocations(Fig.10).

Fig.2

Octagonal

Round

1-1/2˝

Fig.3

Wallmount Eavemount

Fig.4

Fig.7

Fig.10

5°

ENERGYSTAR

issponsoredbytheU.S.

EnvironmentalProtectionAgency&U.S.

DepartmentofEnergy.

Visitwww.energystar.govtolearnmore.

Fig.8

Mode of MODE Knob How to Set

Operation Adjustment Power Switch

MODEknobarrow

pointstoTEST.

Test Setting

LightsshouldturnONwith

motionbothdayandnight.

LightsshouldturnOFF

after4seconds.

Wall Switch Setting

(connected to ﬁxture)

Keepwallswitch

inONposition.

Motion Activated Setting “Auto”

Lightsshouldturnonwith

motiononlyatnightand

shouldturnOFFafter

1-12min.ofnomotion.

“Auto”MODEknobarrow

pointstoatime

selectionwithinthe

1m-12mtimerange.

Keepwallswitchin

ONposition.

Keepthepower

tothextureON.

Dusk-to-Dawn Setting

(activated only at night)

Lightsshouldstayonfrom

dusktodawnandthenreset

tomotionactivated

settingatthenextdawn.

MODEknobarrow

pointstoatimeselection

withinthe1m-12m

timerange.

Turnthepower

OFF-ON-OFF-ON

within3seconds;lightwill

gointooverridemode.

Return to

Motion Activated Setting

from any of

the above settings.

“Auto”MODEknobarrow

pointstoatimeselection

withinthe1m-12m

timerange.

TurnthepowerOFF

foratleast90seconds

andthenbackON.

Problem Cause / Solution

Outdoor Lights

Do Not Come

On With Motion

At Night

Nopowertothexture.

 • Checkifcircuitbreakertripped.

 • ConrmwallswitchisON.

Bulbisfaulty.

 •Replacebulb.

Surroundingexternalambientlightistoobright.(Ifso,theunitmay

thinkitisdaytime.)

 • Re-aimthehead.

 • Relocateorrepositiontheunitawayfromthelight.

TURN OFF POWER BEFORE CONTINUING

Wiringtotheunitisloose.

 • Checkwiring,andreconnectifnecessaryusingwire

  nuts(E)provided.

Outdoor Lights

Come On For No

Apparent Reason

At Night

Thereismotioninthedetectionzone.

 • Makesurethesensorisnotpickingupmovingobjectssuchas

  trees,trafc,etc.

TEST FOR YOURSELF.

 • Coverthesensorlenswithcardboardtopreventsensorfrom

  detectingmotion.Ifthelightstaysoff,somethinginthedetection

  zoneistriggeringthesensor.

•Ifthisisthecase,reducethesensitivity.

 • Repositionthesensor.

  *Ifthelightstaysonwiththesensorlenscovered,contact

  customerservice.

Unitisinthemotionactivatedsetting.

 •Makesure“Auto”MODEknobissetbetween1m-12m.

Fig.9

Fig.6

Fig.5

2-YEAR LIMITED WARRANTY

THEFOLLOWINGWARRANTYISEXCLUSIVEANDINLIEUOFALLOTHERWARRANTIES,

WHETHEREXPRESS,IMPLIEDORSTATUTORYINCLUDING,BUTNOTLIMITEDTO,ANY

WARRANTYOFMERCHANTABILITYORFITNESSFORANYPARTICULARPURPOSE.

CooperLighting,LLC(“CooperLighting”)warrantstocustomersthat,foraperiodoftwoyears

fromthedateofpurchase,CooperLighting’sproductswillbefreefromdefectsinmaterialsand

workmanship.TheobligationofCooperLightingunderthiswarrantyisexpresslylimitedtothe

provisionofreplacementproducts.Thiswarrantyisextendedonlytotheoriginalpurchaserof

theproduct.Apurchaser’sreceiptorotherproofofdateoforiginalpurchaseacceptableto

CooperLighting.Thisisrequiredbeforewarrantyperformanceshallberendered.

ThiswarrantydoesnotapplytoCooperLightingproductsthathavebeenalteredorrepairedorthat

havebeensubjectedtoneglect,abuse,misuseoraccident(includingshippingdamages).This

warrantydoesnotapplytoproductsnotmanufacturedbyCooperLightingwhichhavebeensupplied,

installed,and/orusedinconjunctionwithCooperLightingproducts.Damagetotheproductcausedby

replacementbulbsorcorrosionordiscolorationofbrasscomponentsarenotcoveredbythiswarranty.

LIMITATIONOFLIABILITY:

INNOEVENTSHALLCOOPERLIGHTINGBELIABLEFORSPECIAL,INDIRECT,INCIDENTAL,OR

CONSEQUENTIALDAMAGES(REGARDLESSOFTHEFORMOFACTION,WHETHERINCONTRACT,

STRICTLIABILITY,ORINTORTINCLUDINGNEGLIGENCE),NORFORLOSTPROFITS;NORSHALL

THELIABILITYOFCOOPERLIGHTINGFORANYCLAIMSORDAMAGEARISINGOUTOFOR

CONNECTEDWITHTHESETERMSORTHEMANUFACTURE,SALE,DELIVERY,USE,MAINTENANCE,

REPAIRORMODIFICATIONOFCOOPERLIGHTINGPRODUCTS,ORSUPPLYOFANYREPLACEMENT

PARTSTHEREFORE,EXCEEDTHEPURCHASEPRICEOFCOOPERLIGHTINGPRODUCTSGIVINGRISE

TOACLAIM.NOLABORCHARGESWILLBEACCEPTEDTOREMOVEORINSTALLFIXTURES.

Toobtainwarrantyservice,pleasecontactCooperLighting,LLC,at1-800-334-6871,press

option2forCustomerService,orviae-mail[email protected]and

includethefollowinginformation:

•Name,addressandtelephonenumber

•Dateandplaceofpurchase

•Catalogandquantitypurchase

•Detaileddescriptionofproblem

AllreturnedproductsmustbeaccompaniedbyaReturnGoodsAuthorizationNumberissued

bytheCompanyandmustbereturnedfreightprepaid.AnyproductreceivedwithoutaReturn

GoodsAuthorizationNumberfromtheCompanywillberefused.

CooperLighting,LLCisnotresponsibleformerchandisedamagedintransit.Repairedor

replacedproductsshallbesubjecttothetermsofthiswarrantyandareinspectedwhen

packed.Evidentorconcealeddamagethatismadeintransitshouldbereportedatonceto

thecarriermakingthedeliveryandaclaimledwiththem.

ReproductionsofthisdocumentwithoutpriorwrittenapprovalofCooperLighting,LLCarestrictlyprohibited.

For assistance, call 1-800-334-6871 or e-mail us at [email protected]

PrintedinChina

Oneormoreofthesepatentsmayapply,additionalpatentspending:6,175,309;5,381,323;D433,771;D431,092;D435,924;

D434,165;D374,496;D431,319

ARTÍCULOS NECESARIOS

(se compran por separado)

•Destornilladorencruz(Phillips)

•Calafateodesiliconaresistentealaintemperie

•(2)lámparasparaproyectortipoPAR38de100W(máximo)

NOTA:EsteaccesoriofuediseñadoparatrabajarconbombillasreectorasdeHalógenoPARde

150vatioscomomáximo.Paramayorecienciadeenergía,usebombillasreectoras

HalógenoPARdemenorvataje.Noserecomiendaelusodebombillasuorescentes

compactas(CFL)porquetienenparteselectrónicasquepuedeninterferirconlasfunciones

dedeteccióndemovimientodesuaccesorio.ParacumplirconlosrequerimientosdeENERGY

STAR®,lapotenciamáximadelabombillanodebeexceder250W.

CÓMO FUNCIONA

PIRfuncionamuybienenladeteccióndemovimientolateral

enunrangodedetecciónde270°.ElRadarDopplerPrecision

Plus™haceunexcelentetrabajodetectandomovimientode

acercamientoyalejamientodelaunidad.Lacombinaciónde

ambossistemasproporcionaprecisiónavanzadaycobertura

completadentrodelrangodedetección.Elmovimientodesde

cualquierdireccióndispararáelreector–inclusoentemperaturas

extremasdecaloryfrío.

ADVERTENCIAS Y PRECAUCIONES

•Leaestasinstrucciones.

•Guardeestasinstrucciones.

•Atiendatodaslasadvertencias.

•Sigatodaslasinstrucciones.

•Sóloparausoenexteriores.

•cULusparaubicacionesmojadas.

•Elportalámparasdebeestarconectadoaunafuentedeenergíade120Voltios,60Hz.

 Cualquierotrotipodeconexiónanulalagarantía.

•Elportalámparasdebeserinstaladoporpersonasconexperienciaencableadodomésticoo

 porunelectricistacalicado.Elsistemaeléctricoyelmétododeconexióneléctricadelporta-

 lámparasdebecumplirconelCódigoeléctriconacionalyloscódigoslocalessobreedicios.

•Reemplacesiemprelabombillaconunadelmismovatiajeomásbajoqueelmarcado.Si

 instalalámparasdemayorpotencia,puedecrearriesgodeincendio.Siusalámparasde

 mayorpotencia,seanulalagarantía.(Utiliceunabombilladehalógenodeunmáximode

 150W.)ParacumplirconlosrequerimientosdeENERGYSTAR®,lapotenciamáximadela

 bombillanodebeexceder250W.

•Manténgaloalejadodeobjetosinamables.Nocoloqueelartefactoen

 posicióndentrode1pulgada(2,5cm)decualquiermaterialcombustible.

•¡LabombillaseCALIENTArápidamente!

•Lalámparayelartefactosecalientanextremadamenteduranteeluso.Antesdeintentar

 reposicionarelartefacto,dejequeseenfríetotalmente.

•Sidesarmaelartefacto,seanulalagarantía.

•Lalámparaespercableadaparafacilitarlainstalación.

•Utiliceconductoresdesuministroquesoportenunmínimode90°C.

•Instaleelartefactosobreunacajaeléctricaempotradaosupercialconconexiónatierra

 marcadaparausarenlugareshúmedos.

•Nopermitaquelacabezadeldetectortoqueelalojamientodelalámpara-mantengapor

 lomenos1/2˝(1,27cm)deespacioentreelaccesorioyeldetector.

•Sisereemplazaelvidrio,utilicesolovidriodeseguridadcompactadodeigualgrosor.

•Paraunfuncionamientoyprotecciónadecuadoscontraposiblesdaños,losbotonesde

 ajustedelacabezadelsensordemovimientosedebenajustarendirecciónalpiso.

•Nouseesteaparatocercadeagua.

•Limpieúnicamenteconuntraposeco.

•Noobstruyalasaberturasdeventilación.Instaledeconformidadconlasinstrucciones

 delfabricante.

•Noinstalecercadefuentesdecalortalescomoradiadores,rejillasdeairecaliente,estufas

 uotrosaparatos(incluyendoamplicadores)queproduzcancalor.

•Useúnicamenteacoplamientos/accesoriosespecicadosporelfabricante.

•EstedispositivocumpleconlaParte15delasReglasdelaComisiónFederalde

 Comunicaciones(FCC)delosE.U.deA.Laoperaciónestásujetaalasdoscondiciones

 siguientes:(1)Estedispositivonopuedecausarinterferenciadañina,y(2)estedispositivo

 debeaceptartodainterferenciarecibida,incluyendolainterferenciaquepuedacausarun

 funcionamientoindeseado.SegúnlaParte15delasReglasdelaFCC,todocambioo

 modicaciónaldetectordemovimientodescriptoenestahojadeinstruccionesqueno

 estéexpresamenteaprobadoporCooperLighting,LLCpodríaanularlaautorizacióndel

 usuarioparaoperarelequipo.

NOTA:Esteequipohasidoprobado,ysehavericadoquecumpleconloslímitesdeun

dispositivodigitalClaseB,deacuerdoconlaparte15delasReglasdelaFCC.Estoslímites

estándiseñadosandeproveerunaprotecciónrazonablecontralainterferenciadañina

enunainstalaciónresidencial.Esteequipogenera,usaypuedeirradiarenergíaderadio

frecuencia,ysinoseinstalayutilizadeacuerdoconlasinstrucciones,puedecausar

interferenciadañinaenlascomunicacionesderadio.Sinembargo,nosegarantizaqueno

ESPAÑOL

Hasta

90pies

270grados

Problem Cause / Solution

Lights Stay On At

Night And Do

Not Turn Off

Thereismotioninthedetectionzone.

 • Makesurethesensorisnotpickingupmovingobjectssuchas

  trees,trafc,etc.

 • Reducethesensitivity.

 • Repositionthesensor.

Unitisinoverridemode(ifthereisnomotion).

 • TurnthelightswitchtotheOFFpositionfor90seconds,andthen

  turnbacktotheONpostion.Thiswillsendtheunitbackintothe

  motionactivatedsetting“Auto”.

  *Ifthelightstaysonwiththesensorlenscovered,contact

  customerservice.

Unitisinthe“Auto”mode.

 •Makesuretheunitissetbetween1m-12m(“Auto”mode).

Lights

Continuously

Blink On And

Off At Night

Thelightgivenfromtheunit’sownlampisaffectingthe

motionsensor.

 • Re-aimthelamp.

 • Repositionmotionsensor.

MakesureknobisnotpositionedbetweenTESTand1m.

 • Repositionknobclosertoselectedfunction,eitherTEST,or1m.

Lights Are On

During The Day

ThecontrolsonthebottomofthemotionsensorareintheTESTmode.

 •RepositionMODEknoboffofTESTtoatimeselection(1m-12m).

Themotiondetectorisshadowed.

 • Repositionmotionsensor.

Red LED Indicator

Light Comes ON

And OFF During

Daylight Hours

Duringdaylighthours,theredLEDindicatorwillashwhenmotion

isdetected.Thisisnormal.

Page is loading ...

All-Pro MS276RD Operating instructions

Brand: All-Pro

Model: MS276RD

Category: Work lights

Type: Operating instructions

This manual is also suitable for

MS276RDW

Download PDF

report

in other languages

español: All-Pro MS276RD Instrucciones de operación

All-Pro MS276RD Operating instructions

This manual is also suitable for

All-Pro MS276RD Operating instructions

in other languages

Related papers

Other documents