Cooper Lighting MS185W User manual

Instruction Manual/Instrucciones

Questions?/¿Preguntas? 1-800-334-6871 [email protected]

•Disassemblyofyourxturewillvoidthewarranty.

•Yourxtureisprewiredandpreassembledforeasyinstallation.

•MINIMUM90°CSUPPLYCONDUCTORS.

•ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowing

 twoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust

 acceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

 UnderPart15oftheFCCRules,anychangesormodicationstothemotiondetector

 describedinthisinstructionsheetthatarenotexpresslyapprovedbyCooperLighting,LLC

 couldvoidtheuser’sauthoritytooperatetheequipment.

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

digitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.This

equipmentgenerates,usesandcanradiateradiofrequencyenergyandifnotinstalled

andusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradio

communications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,

whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotryto

correcttheinterferencebyoneormoreofthefollowingmeasures:

 -Reorientorrelocatethereceivingantenna.

 -Increasetheseparationbetweentheequipmentandreceiver.

 -Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

  isconnected.

 -Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

WARNING: FCC Regulations state that any unauthorized changes or modiﬁcations

to this equipment not expressly approved by the manufacturer could void the user’s

authorization to operate this equipment.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

•Installthemotionsensor/transmitter8-12feet

 abovetheground.(Motionsensorislesssensitive

 above12feet.)

•Locatemotionsensorsomotionmovesacross

 detectionzone(Fig.1).

•Locatesensorawayfromheatproducingsourcesto

 preventfalsetriggering.Alsobeverycarefulnotto

 includeobjectssuchaswindows,whitewallsand

 waterinthedetectionzone.

•Locatesensorawayfrommovingobjectssuchas

 trees,largeshrubsandstreettrafc.

•Donotinstallmorethanonemotionactivated

 oodlightononewallswitch.

PACKAGING CONTENTS/CONTENIDO DEL PAQUETE

ITEMS REQUIRED

(Purchase separately)

•Phillipsscrewdriver

•Outdoorweatherproofsiliconecaulking

•(2)100watt(MAX)PAR38oodlightbulbs

NOTE:Thisxturewasdesignedtoworkwithupto150wattmaximumPARhalogenood

bulbs.Forimprovedenergyefciency,lowerwattagePARhalogenoodbulbsmaybeused.

CompactFluorescent(CFL)bulbscontainelectronicswhichmayinterferewiththemotion

sensingfunctionofyourxtureandarenotrecommended.TomeetENERGYSTAR

® 

requirements,maximumlampwattagecannotexceed250watts.

HOW IT WORKS

Yourmotionactivatedoodlightsensesheatimagesfrom

objectssuchaspeople,largeanimalsandautomobileengines.

Whenmotionisdetected,thelightswillautomaticallyturn

on.Oncemotionhasstopped,thelightswillturnoffaftera

preselectedtimedelay.Yourmotionactivatedoodlightmay

alsobeusedasastandardoodlight.

WARNINGS AND CAUTIONS

•Readtheseinstructions.

•Keeptheseinstructions.

•Heedallwarnings.

•Followallinstructions.

•Foroutdooruseonly.

•cULusLISTEDforwetlocations.

•Connectxturetoa120volt,60Hzpowersource.Anyotherconnectionvoidsthewarranty.

•Fixtureshouldbemountedtoagroundedrecessedmountedstandardjunctionboxmarked

 foruseinwetlocations.

•Suitableforwallmountoreavemountonly.NOTsuitableforgroundmountinstallation.

•Donotallowsensorheadtotouchlighthousing–maintainatleast1in.spacebetween

 xtureandsensor.

•Fixtureshouldbeinstalledbypersonswithexperienceinhouseholdwiringorbyaqualied

 electrician.Theelectricalsystem,andthemethodofelectricallyconnectingthexturetoit,

 mustbeinaccordancewiththeNationalElectricalCodeandlocalbuildingcodes.

•Alwaysreplacebulbwiththesamewattageorlowerwattagethanincluded.Installinga

 bulbofahigherwattagecouldcreatearehazard.Useofahigherwattagebulbwillvoid

 thewarranty(maximum150watthalogenbulb).TomeetENERGYSTAR

requirements,

 maximumlampwattagecannotexceed250watts.

•Forproperoperationandprotectionagainstdamage,themotion

 sensorheadadjustmentknobsmustbefacingtheground.

•Keepawayfromammableobjects.Donotpositionxturewithin2in.

 ofanycombustiblematerials.

MS185 (Bronze)

MS185W (White)

A. Motion detector

and light ﬁxture

Detector de

movimiento y

artefacto de luz

ENGLISH

Upto

70feet

180degrees

D. (2) #6 and (2) #8 mounting screws

(use the size that ﬁts your junction box)

(2) Tornillos #6 y (2) tornillos #8 de montaje

(utilice el tamaño que mejor se adecue a

su caja de conexión)

B. Coverplate gasket

Junta de la placa

de cubierta

E. (3) Wire nuts

(3) Tuercas

para alambre

C. (2) Lampholder gaskets

(2) Juntas obturadoras

del receptáculo

F. Color-matched

center hole plug

Tapón para agujero

central de color

coincidente

G. Center bolt

Perno central

H. Mounting bracket

Soporte de montaje

Fig.1

SELECTING YOUR DESIRED FEATURE

TROUBLESHOOTING

MOUNTING AND WIRING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect

power at fuse or circuit breaker before installing

or servicing.

NOTE:Fixturecanbewalloreavemounted.

NOTE:Coverplatemountstorecessedmounted

standardjunctionboxes(Fig.2).Junctionboxmustbe

atleast1-1/2in.indepthforproperinstallationfor

recessedmountapplication.

1. Lineuptheholesonthemountingbracket(H)with

theholesonyourjunctionbox.Usingeither(2)#6

screwsor(2)#8screws(D)(dependingonsizeof

theholesinyourjunctionbox),attachthemounting

bracket(H)toyourjunctionbox(Fig.3).

2. Threadxturewiresthroughcoverplategasket(B)

 (Fig.4).

3. Connectxtureblackwiretohouseblackwire,

xturewhitewiretohousewhitewire,andcopper

coloredgroundwire(comingfromthexture

coverplate)tohousegroundwireusingwirenuts

(E)provided.

4. Attachxture(A)tothemountingbracket(H)using

thecenterbolt(G)provided.Besurenoloosewires

remainstickingoutfromunderneaththecoverplate.

Insertplasticcolor-matchedplug(F)incenterbolt

holefornishedappearance(Fig.5).

5. Applysiliconecaulkaroundtheedgesofthe

coverplatetoprovideawatertightsealfromrain

andmoisture.

6. Insertlampholdergaskets(C)intolampholder

assembly,tightlyagainstlampholder,andscrew

bulbsintoeachlampholder(Fig.6).(Donot

overtightenbulbs.)

7. Turnonpoweratmainfuse/breakerbox.

OPERATING YOUR FIXTURE

1. Moveslideswitchonbottomofthesensor

to“TEST”.Setsensitivityknobtomedium 

(halfway)(Fig.7).

2. Turnonthepowertoxture.Allowxturetowarm

upapproximately40secondsbeforetesting.(Lights

maynotcomeonduringwarm-upperiod.)

3. Aimsensorheadtowarddesireddetectionarea,

maintaininga15°downangletoallowmoisture

todrain.

NOTE:Maintainairspacingbetweenlampsandsensor

head,atleast1in.Makesuresensorheadispositioned

withcontrolswitchesfacingtowardstheground.

4. Walkacrossthedetectionzoneatthefarthest

distanceyouwishyourdetectortodetectmotion.

5. Adjustsensitivityuntilyougetdesiredresults.Light

willturnoff4secondsafterallmotionstops.

NOTE:Formaximumrangeperformance,allowxture

tooperateinanymode(withpowertotheunit)forat

least48hours.

6. Moveslideswitchto4min.or12min.(AUTO

mode).AtdusklightswilloperateintheAUTO

setting.

ENERGY STAR

TomeetENERGYSTAR

requirements,thephotosensorcontrolknobmustbeinthe

“Auto”modetopreventoperationduringfulldaylight.Maximumlampwattagecannot

exceed250watts.

Fig.2

OctagonalRound

TEST 4 MIN. 12 MIN.

SENSITIVITY

Fig.7

Mode of MODE Knob How to Set

Operation Adjustment Power Switch

Test Setting

LightsshouldturnONwith

motionbothdayandnight.

LightsshouldturnOFF

after4seconds.

Keepthepower

tothextureON.

TEST

“Auto” Setting

(motion activated)

LightsshouldturnONwith

motiononlyatnightand

shouldturnOFFafter

4-12minutesofnomotion.

AUTO4MIN

AUTO12MIN

Keepthepower

tothextureON.

Dusk-to-Dawn Setting

(activated only at night)

LightsshouldstayONfrom

dusktodawnandthenreset

to“Auto”settingat

thenextdawn.

AUTO4MIN

AUTO12MIN

Turnthepower

OFF-ON-OFF-ON

within3seconds.

Return to “Auto”

(motion activated) Setting

from any of

the above settings.

AUTO4MIN

AUTO12MIN

TurnthepowerOFF

foratleast40seconds

andthenbackON.

Standard Floodlight Setting

LightsshouldstayON

continuouslybothdayandnight

(mustberesetmanually).

TEST Turnthepower

OFF-ON-OFF-ON

within3seconds.

Problem Cause / Solution

Outdoor Light

Does Not Come

On With Motion

At Night

Nopowertothexture.

 • Checkifcircuitbreakertripped.

 • ConrmwallswitchisON.

Bulbisfaulty.

 •Replacebulb.

Surroundingexternalambientlightistoobright.(Ifso,theunitmay

thinkitisdaytime.)

 • Re-aimthehead.

 • Relocateorrepositiontheunitawayfromthelight.

TURN OFF POWER BEFORE CONTINUING

Wiringtotheunitisloose.

 • Checkwiring,andreconnectifnecessaryusingwire

  nuts(E)provided.

Outdoor Light

Comes On For No

Apparent Reason

At Night

Thereismotioninthedetectionzone.

 • Makesurethesensorisnotpickingupmovingobjectssuchas

  trees,trafc,etc.

TEST FOR YOURSELF.

 • Coverthesensorlenswithcardboardtopreventsensorfrom

  detectingmotion.Ifthelightstaysoff,somethinginthedetection

  zoneistriggeringthesensor.

  •Ifthisisthecase,reducethesensitivity.

 • Repositionthesensor.

  *Ifthelightstaysonwiththesensorlenscovered,contact

  customerservice.

Light Stays On At

Night And Does

Not Turn Off

Thereismotioninthedetectionzone.

 • Makesurethesensorisnotpickingupmovingobjectssuchas

  trees,trafc,etc.

 • Reducethesensitivity.

 • Repositionthesensor.

Unitisinoverridemode(ifthereisnomotion).

 • TurnthelightswitchtotheOFFpositionfor40seconds,andthen

  turnbacktotheONposition.Thiswillsendtheunitbackintothe

  “Auto”mode.

  *Ifthelightstaysonwiththesensorlenscovered,contact

  customerservice.

Light

Continuously

Blink On and

Off At Night

Thelightgivenfromtheunit’sownlampisaffectingthe

motionsensor.

 • Re-aimthelamp.

 • Repositionmotionsensor.

Fig.3

Fig.5

Fig.6

Wallmount

Eavemount

Fig.4

ENERGYSTAR

issponsoredbytheU.S.

EnvironmentalProtectionAgency&U.S.

DepartmentofEnergy.

Visitwww.energystar.govtolearnmore.

1-1/2in. 1-1/2in.

Light Is On

During The Day

Thecontrolsonthebottomofthemotionsensorareinthetestmode.

 • MovetheswitchtotheAUTO4or12position.

Themotiondetectorisshadowed.

 • Repositionmotionsensor.

Cannot Activate

Dusk to Dawn

Mode At Night

(Override)

Surroundingexternalambientlightistoobright.(Ifso,theunitmay

thinkitisdaytime.)

 • Re-aimthehead.

 • Relocateorrepositiontheunitawayfromthelight.

Notenoughtimeisallowedtoenterthedusktodawnmode.

 • TurnpowerOFF-ON-OFF-ONwithin3seconds.

Thereismorethanonextureonanindoorwallswitch.

 • Ifso,putthemonseparateswitches.

2-YEAR LIMITED WARRANTY

THEFOLLOWINGWARRANTYISEXCLUSIVEANDINLIEUOFALLOTHERWARRANTIES,

WHETHEREXPRESS,IMPLIEDORSTATUTORYINCLUDING,BUTNOTLIMITEDTO,ANY

WARRANTYOFMERCHANTABILITYORFITNESSFORANYPARTICULARPURPOSE.

CooperLighting,LLC(“CooperLighting”)warrantstocustomersthat,foraperiodoftwoyears

fromthedateofpurchase,CooperLighting’sproductswillbefreefromdefectsinmaterials

andworkmanship.TheobligationofCooperLightingunderthiswarrantyisexpresslylimited

totheprovisionofreplacementproducts.Thiswarrantyisextendedonlytotheoriginal

purchaseroftheproduct.Apurchaser’sreceiptorotherproofofdateoforiginalpurchase

acceptabletoCooperLighting.Thisisrequiredbeforewarrantyperformanceshallberendered.

ThiswarrantydoesnotapplytoCooperLightingproductsthathavebeenalteredorrepaired

orthathavebeensubjectedtoneglect,abuse,misuseoraccident(includingshippingdamages).

ThiswarrantydoesnotapplytoproductsnotmanufacturedbyCooperLightingwhichhavebeen

supplied,installed,and/orusedinconjunctionwithCooperLightingproducts.Damagetothe

productcausedbyreplacementbulbsorcorrosionordiscolorationofbrasscomponentsare

notcoveredbythiswarranty.

LIMITATIONOFLIABILITY:

INNOEVENTSHALLCOOPERLIGHTINGBELIABLEFORSPECIAL,INDIRECT,INCIDENTAL,OR

CONSEQUENTIALDAMAGES(REGARDLESSOFTHEFORMOFACTION,WHETHERINCONTRACT,

STRICTLIABILITY,ORINTORTINCLUDINGNEGLIGENCE),NORFORLOSTPROFITS;NORSHALL

THELIABILITYOFCOOPERLIGHTINGFORANYCLAIMSORDAMAGEARISINGOUTOFOR

CONNECTEDWITHTHESETERMSORTHEMANUFACTURE,SALE,DELIVERY,USE,MAINTENANCE,

REPAIRORMODIFICATIONOFCOOPERLIGHTINGPRODUCTS,ORSUPPLYOFANYREPLACEMENT

PARTSTHEREFORE,EXCEEDTHEPURCHASEPRICEOFCOOPERLIGHTINGPRODUCTSGIVINGRISE

TOACLAIM.NOLABORCHARGESWILLBEACCEPTEDTOREMOVEORINSTALLFIXTURES.

Toobtainwarrantyservice,pleasecontactCooperLighting,LLC,at1-800-334-6871,press

option2forCustomerService,orviae-mail[email protected]and

includethefollowinginformation:

•Name,addressandtelephonenumber

•Dateandplaceofpurchase

•Catalogandquantitypurchase

•Detaileddescriptionofproblem

AllreturnedproductsmustbeaccompaniedbyaReturnGoodsAuthorizationNumberissued

bytheCompanyandmustbereturnedfreightprepaid.AnyproductreceivedwithoutaReturn

GoodsAuthorizationNumberfromtheCompanywillberefused.

CooperLighting,LLCisnotresponsibleformerchandisedamagedintransit.Repairedor

replacedproductsshallbesubjecttothetermsofthiswarrantyandareinspectedwhen

packed.Evidentorconcealeddamagethatismadeintransitshouldbereportedatonceto

thecarriermakingthedeliveryandaclaimledwiththem.

ReproductionsofthisdocumentwithoutpriorwrittenapprovalofCooperLighting,LLCarestrictlyprohibited.

For assistance, call 1-800-334-6871 or e-mail us at [email protected]

PrintedinChina

ARTÍCULOS NECESARIOS

(se compran por separado)

•Destornilladorencruz(Phillips)

•Calafateodesiliconaresistentealaintemperie

•(2)lámparasparaproyectortipoPAR38de100W(máximo)

NOTA:EsteaccesoriofuediseñadoparatrabajarconbombillasreectorasdeHalógenoPARde

150vatioscomomáximo.Paramayorecienciadeenergía,usebombillasreectoras

HalógenoPARdemenorvataje.Noserecomiendaelusodebombillasuorescentes

compactas(CFL)porquetienenparteselectrónicasquepuedeninterferirconlasfunciones

dedeteccióndemovimientodesuaccesorio.ParacumplirconlosrequerimientosdeENERGY

STAR

,lapotenciamáximadelabombillanodebeexceder250W.

CÓMO FUNCIONA

Lalámparadealtaintensidadactivadapormovimiento

detectaimágenestérmicasdeobjetostalescomo

personas,animalesgrandesymotoresdeautomóviles.

Problem Cause / Solution

ESPAÑOL

Cuandosedetectemovimiento,laluzseencenderá

automáticamente.Unavezqueelmovimientohaya

cesado,laluzseapagarádespuésdeuntiempode

retardopreseleccionado.Estalámparadealtaintensidad

activadapormovimientotambiénpuedeserutilizada

comounalámparadealtaintensidadestándar.

ADVERTENCIAS Y PRECAUCIONES

•Leaestasinstrucciones.

•Guardeestasinstrucciones.

•Atiendatodaslasadvertencias.

•Sigatodaslasinstrucciones.

•Sóloparausoenexteriores.

•cULusparaubicacionesmojadas.

•Elportalámparasdebeestarconectadoaunafuentedeenergíade120Voltios,60Hz.

 Cualquierotrotipodeconexiónanulalagarantía.

•Debemontarelartefactosobreunacajadeconexionesempotradascontomade

 tierramarcadaparausarenlugareshúmedos.

•Adecuadoparainstalarseenlaparedoenalerossolamente.Noesadecuadopara

 instalarsemontándoloenelsuelo.

•Nopermitaqueelsensortoqueelalojamientodelalámpara–mantengaporlomenos

 1pulgada(2,54cm)deespacioentreelportalámparasyelsensor.

•Elportalámparasdebeserinstaladoporpersonasconexperienciaencableado

 domésticooporunelectricistacalicado.Elsistemaeléctricoyelmétododeconexión

 eléctricadelportalámparasdebecumplirconelCódigoeléctriconacionalyloscódigos

 localessobreedicios.

•Reemplacesiemprelabombillaconunadelmismovatiajeomásbajoqueelmarcado.Si

 instalalámparasdemayorpotencia,puedecrearriesgodeincendio.Siusalámparasde

 mayorpotencia,seanulalagarantía.(Utiliceunabombilladehalógenodeunmáximode

 150W.)ParacumplirconlosrequerimientosdeENERGYSTAR

,lapotenciamáximadela

 bombillanodebeexceder250W.

•Paraunfuncionamientoyprotecciónadecuadoscontraposiblesdaños,losbotonesde

 ajustedelacabezadelsensordemovimientosedebenajustarendirecciónalpiso.

•Manténgaloalejadodeobjetosinamables.Nocoloqueelartefactoen

 posicióndentrode2pulgadas(5cm)decualquiermaterialcombustible.

•Sidesarmaelartefacto,seanulalagarantía.

•Lalámparaespercableadayensambladoparafacilitarlainstalación.

•UTILICECONDUCTORESDESUMINISTROQUESOPORTENUNMÍNIMODE90°C.

•EstedispositivocumpleconlaParte15delasReglasdelaComisiónFederalde

 Comunicaciones(FCC)delosE.U.deA.Laoperaciónestásujetaalasdoscondiciones

 siguientes:(1)Estedispositivonopuedecausarinterferenciadañina,y(2)estedispositivo

 debeaceptartodainterferenciarecibida,incluyendolainterferenciaquepuedacausarun

 funcionamientoindeseado.SegúnlaParte15delasReglasdelaFCC,todocambioo

 modicaciónaldetectordemovimientodescriptoenestahojadeinstruccionesqueno

 estéexpresamenteaprobadoporCooperLighting,LLCpodríaanularlaautorizacióndel

 usuarioparaoperarelequipo.

NOTA:Esteequipohasidoprobado,ysehavericadoquecumpleconloslímitesdeun

dispositivodigitalClaseB,deacuerdoconlaParte15delasReglasdelaFCC.Estoslímites

estándiseñadosandeproveerunaprotecciónrazonablecontralainterferenciadañina

enunainstalaciónresidencial.Esteequipogenera,usaypuedeirradiarenergíaderadio

frecuencia,ysinoseinstalayutilizadeacuerdoconlasinstrucciones,puedecausar

interferenciadañinaenlascomunicacionesderadio.Sinembargo,nosegarantizaqueno

vayaaproducirseinterferenciaenunainstalaciónenparticular.Siesteequipoefectivamente

causaunainterferenciadañinaenlarecepciónderadiootelevisión,loquepuede

determinarseapagándoloyencendiéndolo,serecomiendaalusuarioquetratedecorregir

lainterferenciapormediodeunaomásdelassiguientesmedidas:

 -Reorienteocambiedelugarlaantenareceptora.

 -Aumentelaseparaciónentreelequipoyelreceptor.

 -Conecteelequipoenuntomacorrientequeestéenuncircuitodiferentedeaquélalque

  seconectaelreceptor.

 -Consulteasuproveedor,oauntécnicoderadio/TVexperimentado,paraqueleayuden.

ADVERTENCIA: Las Reglamentaciones de la FCC establecen que todo cambio o

modiﬁcación no autorizados en este equipo, que no estén aprobados expresamente por

el fabricante, podrían anular la autorización del usuario para operar el equipo.

GUARDE ESTAS INSTRUCCIONES.

PARA OBTENER LOS MEJORES RESULTADOS

•Instaleelsensordemovimiento/transmisora

 8–12pies(2,45–3,65m)dealturasobreelsuelo

 (porencimade12pies/3,65m,elsensorde

 movimientoesmenossensible).

•Coloqueelportalámparasdemaneraquesemueva

 portodalazonadedetección(Fig.1).

•Coloqueelsensorlejosdefuentesqueproduzcan

 calor,andeevitarfalsosdisparos.Además,medida

 deloposible,tengamuchocuidadodenoincluir

 objetostalescomoventanas,paredesblancasy

 agua,enlazonadedetección.

Hasta

70pies

180grados

Fig.1

Page is loading ...

Cooper Lighting MS185W User manual

Related papers

Other documents