All-Pro MS276RD Operating instructions

Category
Work lights
Type
Operating instructions

This manual is also suitable for

Instruction Manual/Instrucciones
Questions?/¿Preguntas? 1-800-334-6871 [email protected]
1
•Donotallowsensorheadtotouchlighthousing–maintainatleast1/2inchspacebetween
xtureandsensor.
•Iflensisreplaced,useonlytemperedsafetyglassofequalthickness.
•Forproperoperationandprotectionagainstdamage;themotionsensorheadadjustment
knobsmustbefacingtheground.
•Donotusethisapparatusnearwater.
•Cleanonlywithadrycloth.
•Donotblockanyventilationopenings.Installinaccordancewiththemanufacturersinstructions.
•Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stovesorother
apparatus(includingampliers)thatproduceheat.
•Onlyuseattachments/accessoriesspeciedbythemanufacturer.
•ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwo
conditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust
acceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
UnderPart15oftheFCCRules,anychangesormodicationstothemotiondetector
describedinthisinstructionsheetthatarenotexpresslyapprovedbyCooperLighting,LLC
couldvoidtheuser’sauthoritytooperatetheequipment.
NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital
device,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonable
protectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,
usesandcanradiateradiofrequencyenergyandifnotinstalledandusedinaccordancewith
theinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereis
noguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoes
causeharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturning
theequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneor
moreofthefollowingmeasures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparationbetweentheequipmentandreceiver.
-Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver
isconnected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s authorization
to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
•Installthemotionsensor/transmitter8-12feetabove
ground(motionsensorislesssensitiveabove12feet).
•Locatemotionsensorsomotionmoveslaterallyor
towardsthedetectionzone(Fig.1).
•Locatesensorawayfromheatproducingsourcesto
preventfalsetriggering.Alsobeverycarefulnotto
includeobjectssuchaswindows,whitewallsand
waterinthedetectionzone.
•Locatextureawayfrommovingobjectssuchas
trees,largeshrubsandstreettrafc.
•Donotinstallmorethanonemotionactivatedoodlightononewallswitch.
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE
ITEMS REQUIRED
(Purchase separately)
•Phillipsscrewdriver
•Outdoorweatherproofsiliconecaulking
•(2)100watt(MAX)PAR38oodlightbulbs
NOTE:Thisxturewasdesignedtoworkwithupto150wattmaximumPARhalogenoodbulbs.
Forimprovedenergyefciency,lowerwattagePARhalogenoodbulbsmaybeused.Compact
Fluorescent(CFL)bulbscontainelectronicswhichmayinterferewiththemotionsensingfunction
ofyourxtureandarenotrecommended.TomeetENERGYSTAR
®
requirements,maximumlamp
wattagecannotexceed250watts.
HOW IT WORKS
PIRdoesagoodjobofdetectinglateralmotionacrossthe270°
rangeofdetection.PrecisionPlusDopplerRadar™doesan
excellentjobdetectingmotiontowardsandawayfromtheunit.
Bothsystemscombinedprovideenhancedaccuracyandcomplete
coveragewithinthedetectionrange.Motionfromanydirectionwill
triggeryouroodlight—evenduringhotorcoldtemperatureextremes.
WARNINGS AND CAUTIONS
•Readtheseinstructions.
•Keeptheseinstructions.
•Heedallwarnings.
•Followallinstructions.
•Foroutdooruseonly.
•cULusLISTEDforwetlocations.
•Connectxturetoa120volt,60Hzpowersource.Anyotherconnectionvoidsthewarranty.
•Fixtureshouldbeinstalledbypersonswithexperienceinhouseholdwiringorbyaqualied
electrician.Theelectricalsystem,andthemethodofelectricallyconnectingthexturetoit,
mustbeinaccordancewiththeNationalElectricalCodeandlocalbuildingcodes.
•Alwaysreplacebulbwiththesamewattageorlowerwattagethanmarked.Installingabulb
ofahigherwattagecouldcreatearehazard.Useofahigherwattagebulbwillvoidthe
warranty.(Maximum150watthalogenbulb.)TomeetENERGYSTAR
®
requirements,
maximumlampwattagecannotexceed250watts.
•Keepawayfromammableobjects.Donotpositionxturewithinoneinch
ofanycombustiblematerials.
•BulbgetsHOTquickly!
•Thebulbandxturegetextremelyhotduringuse.Disconnectpowerandallow
xturetocoolbeforechangingbulborhandlingxture.
•Disassemblyofyourxturewillvoidthewarranty.
•Yourxtureispre-wiredandpre-assembledforeasyinstallation.
•Minimum90°Csupplyconductors.
•Fixturemountstoarecessedorsurfacemountedstandardgroundedjunctionboxmarked
foruseinwetlocations.
MS276RD (Bronze)
MS276RDW (White)
A. Motion detector and light fixture
Detector de movimiento y
artefacto de luz
ENGLISH
Upto
90feet
270degrees
Fig.1
D. Coverplate gasket
Junta de la placa
de cubierta
C. (2) #6 and (2) #8 mounting screws
(use the size that fits your junction box)
(2) Tornillos #6 y (2) tornillos #8 de montaje
(utilice el tamaño que mejor se adecue
a su caja de conexión)
I. (2) Lampholder gaskets
(2) Juntas para portalámpara
E. (3) Wire nuts
(3) Tuercas para
alambre
B. Mounting bracket
Soporte de montaje
F. Mounting plate screw
Tornillo para la placa
de montaje
G. Color-matched
center hole plug
Tapón para agujero
central de color
coincidente
H. (2) Light covers
(2) Cubiertas de las luces
2
•Ifthextureismountedhigher,theangleofthe
sensorbelowhorizontalshouldincrease.
5. Walkthroughthedetectionzoneatthefarthestdistanceyouwantyourdetectorto
detectmotion.
6. AdjusttheSENSITIVITYknobuntilyougetdesiredresults.Formorerange,aimsensor
slightlyupward.Forlessrange,aimsensorheadslightlydownward.Lightswillturnoff
4secondsaftermotionstops.
7. Adjustthe“Auto”MODEknobtoatimeselectionfrom1m-12m,dependingonhowmany
minutesyouwantthexturetostayonaftermotionisdetected.Atdusk,thephotocontrol
willactivateyourxturetooperateaccordingtothesettingschosen.
NOTE:DecreasingtheSENSITIVITYwilldecreasethedistancetheunitcandetect.
NOTE:Duringdaylighthours,theredLEDindicatorlightwillashwhenmotionisdetected.
Thisisnormal.
SELECTING YOUR DESIRED FEATURE
ENERGY STAR
®
TomeetENERGYSTAR
®
requirements,thephotosensorcontrolknobmustbeinthe“Auto”
modetopreventoperationduringfulldaylight.Maximumlampwattagecannotexceed250watts.
TROUBLESHOOTING
MOUNTING YOUR FIXTURE
NOTE:Universalcoverplatemountstorecessedor
surfacemountedstandardjunctionboxes(Fig.2).
Junctionboxmustbeatleast1-1/2˝indepthforproper
installationforrecessedmountapplication.
NOTE:Forbestperformancewheninstallingmorethan
onePrecisionPlusDopplerRadar™xture:
•Twoormoreunitsmountedsidebyside(facingthe
samedirection)shouldbeatleast17feetapart.
•Twounitsfacingeachothershouldbemountedat
least100feetapart.
•Fixturecanbewalloreavemounted(Fig.3).
WARNING: Risk of electric shock. Disconnect power
at fuse or circuit breaker before installing or servicing.
1. Lineuptheholesonthemountingbracket(B)with
theholesonyourjunctionbox.Usingeither(2)#6
screwsor(2)#8screws(C)(dependingonthesize
oftheholesinyourjunctionbox),attachthemounting
bracket(B)toyourjunctionbox(Fig.4).
2. Threadxturewiresthroughcoverplategasket(D).
3. Positionthegasket(D)onthecoverplateandconnect
theblackwirefromthexture(A)totheblackhouse
supplywireandthewhitewirefromthexture(A)
tothewhitesupplywireusingthewirenuts(E)
provided.Attachthegroundwirecomingfromyour
housetothecoppergroundwirefromthexture(A)
usingwirenut(E)provided.Ifnohousegroundwire
isavailable,attachthecoppergroundwirefrom
thexture(A)tothejunctionboxifitismetaland
grounded.Ifjunctionboxisnotmetalandnohouse
groundwireisavailable,analternativeground
sourcemustbeusedforsafeoperation(Fig.5).
4. Attachxture(A)tothemountingbracket(B)
usingthemountingplatescrew(F)provided.
Besurenoloosewiresremainstickingoutfrom
underneaththecoverplate.Insertplasticcolor-
matched(G)pluginmountingplatescrewhole
fornishedappearance(Fig.6).
5. Applysiliconecaulkingaroundedgesofcoverplateand
inanyopenholestoprovideawatertightsealfrom
rainandmoisture.
6. Installprotectivelampcovers(H)ontolampholders
byliningupthenipplesonthecovers(H),overthe
lampholderslots.Lockintoplacebytwistingcovers
counterclockwise(Fig.7).
7. Insertgaskets(I)intolampholdersandscrew
bulbsintoeachlampholder(Fig.8).(Donotover
tightenbulbs.)
8. Turnpoweronatmainfuse/breakerbox.
AIMING THE LIGHT
Loosentheknobonthesideofthelampholder.
Tiltlampholderupordowntodesiredposition,then
retightenknob.
WARNING: Deviation from the assembly instructions
may result in a risk of electric shock.
OPERATING YOUR FIXTURE
1. TurnthearrowontheMODEknobto“TEST”fortest
mode(Fig.9).
2. TurnthearrowontheSENSITIVITYknobtoamiddle
pointbetween“+”and“-”.
3. Turnonthepowertothexture(A).Allowxtureto
warmupapproximately90secondsbeforetesting.
(Lightsmayormaynotcomeonduringwarm-up
period;thisisnormal.)
4. Aimsensortowardthegeneraldirectionthatmotion
willbecomingfrom.Maintainatleast1˝ofclearance
betweensensorheadandlamps.Alwaysposition
thesensorheadwithcontrolswitchesfacingtoward
theground.
NOTE: (Sensor Head Placement) Foroptimumdetection,
youmayhavetoexperimentwithaimingandsettings.
Eachlocationwillbedifferentandyourterrainmay
affecttheangleyoursensorneeds.Adjustingtheangle
willchangeyourareaofdetection.Herearesome
generalguidelinestohelpwithsetup:
•8´-12´abovethegroundisagoodrangeforthe
placementofyourxture.
•Foran8´mountingheight,placingthesensorata
5°anglebelowhorizontalshouldworkwellfor
mostlocations(Fig.10).
Fig.2
Octagonal
Round
1-1/2˝
1-1/2˝
Fig.3
Wallmount Eavemount
Fig.4
B
C
C
Fig.7
H
Fig.10
A
ENERGYSTAR
®
issponsoredbytheU.S.
EnvironmentalProtectionAgency&U.S.
DepartmentofEnergy.
Visitwww.energystar.govtolearnmore.
I
A
Fig.8
H
I
H
Mode of MODE Knob How to Set
Operation Adjustment Power Switch
MODEknobarrow
pointstoTEST.
Test Setting
LightsshouldturnONwith
motionbothdayandnight.
LightsshouldturnOFF
after4seconds.
Wall Switch Setting
(connected to fixture)
Keepwallswitch
inONposition.
Motion Activated Setting “Auto”
Lightsshouldturnonwith
motiononlyatnightand
shouldturnOFFafter
1-12min.ofnomotion.
“Auto”MODEknobarrow
pointstoatime
selectionwithinthe
1m-12mtimerange.
Keepwallswitchin
ONposition.
Keepthepower
tothextureON.
Dusk-to-Dawn Setting
(activated only at night)
Lightsshouldstayonfrom
dusktodawnandthenreset
tomotionactivated
settingatthenextdawn.
MODEknobarrow
pointstoatimeselection
withinthe1m-12m
timerange.
Turnthepower
OFF-ON-OFF-ON
within3seconds;lightwill
gointooverridemode.
Return to
Motion Activated Setting
from any of
the above settings.
“Auto”MODEknobarrow
pointstoatimeselection
withinthe1m-12m
timerange.
TurnthepowerOFF
foratleast90seconds
andthenbackON.
Problem Cause / Solution
Outdoor Lights
Do Not Come
On With Motion
At Night
Nopowertothexture.
• Checkifcircuitbreakertripped.
• ConrmwallswitchisON.
Bulbisfaulty.
•Replacebulb.
Surroundingexternalambientlightistoobright.(Ifso,theunitmay
thinkitisdaytime.)
• Re-aimthehead.
• Relocateorrepositiontheunitawayfromthelight.
TURN OFF POWER BEFORE CONTINUING
Wiringtotheunitisloose.
• Checkwiring,andreconnectifnecessaryusingwire
nuts(E)provided.
Outdoor Lights
Come On For No
Apparent Reason
At Night
Thereismotioninthedetectionzone.
• Makesurethesensorisnotpickingupmovingobjectssuchas
trees,trafc,etc.
TEST FOR YOURSELF.
• Coverthesensorlenswithcardboardtopreventsensorfrom
detectingmotion.Ifthelightstaysoff,somethinginthedetection
zoneistriggeringthesensor.
•Ifthisisthecase,reducethesensitivity.
• Repositionthesensor.
*Ifthelightstaysonwiththesensorlenscovered,contact
customerservice.
Unitisinthemotionactivatedsetting.
•Makesure“Auto”MODEknobissetbetween1m-12m.
Fig.9
Fig.6
G
F
A
Fig.5
E
E
E
D
A
3
2-YEAR LIMITED WARRANTY
THEFOLLOWINGWARRANTYISEXCLUSIVEANDINLIEUOFALLOTHERWARRANTIES,
WHETHEREXPRESS,IMPLIEDORSTATUTORYINCLUDING,BUTNOTLIMITEDTO,ANY
WARRANTYOFMERCHANTABILITYORFITNESSFORANYPARTICULARPURPOSE.
CooperLighting,LLC(“CooperLighting”)warrantstocustomersthat,foraperiodoftwoyears
fromthedateofpurchase,CooperLighting’sproductswillbefreefromdefectsinmaterialsand
workmanship.TheobligationofCooperLightingunderthiswarrantyisexpresslylimitedtothe
provisionofreplacementproducts.Thiswarrantyisextendedonlytotheoriginalpurchaserof
theproduct.Apurchaser’sreceiptorotherproofofdateoforiginalpurchaseacceptableto
CooperLighting.Thisisrequiredbeforewarrantyperformanceshallberendered.
ThiswarrantydoesnotapplytoCooperLightingproductsthathavebeenalteredorrepairedorthat
havebeensubjectedtoneglect,abuse,misuseoraccident(includingshippingdamages).This
warrantydoesnotapplytoproductsnotmanufacturedbyCooperLightingwhichhavebeensupplied,
installed,and/orusedinconjunctionwithCooperLightingproducts.Damagetotheproductcausedby
replacementbulbsorcorrosionordiscolorationofbrasscomponentsarenotcoveredbythiswarranty.
LIMITATIONOFLIABILITY:
INNOEVENTSHALLCOOPERLIGHTINGBELIABLEFORSPECIAL,INDIRECT,INCIDENTAL,OR
CONSEQUENTIALDAMAGES(REGARDLESSOFTHEFORMOFACTION,WHETHERINCONTRACT,
STRICTLIABILITY,ORINTORTINCLUDINGNEGLIGENCE),NORFORLOSTPROFITS;NORSHALL
THELIABILITYOFCOOPERLIGHTINGFORANYCLAIMSORDAMAGEARISINGOUTOFOR
CONNECTEDWITHTHESETERMSORTHEMANUFACTURE,SALE,DELIVERY,USE,MAINTENANCE,
REPAIRORMODIFICATIONOFCOOPERLIGHTINGPRODUCTS,ORSUPPLYOFANYREPLACEMENT
PARTSTHEREFORE,EXCEEDTHEPURCHASEPRICEOFCOOPERLIGHTINGPRODUCTSGIVINGRISE
TOACLAIM.NOLABORCHARGESWILLBEACCEPTEDTOREMOVEORINSTALLFIXTURES.
Toobtainwarrantyservice,pleasecontactCooperLighting,LLC,at1-800-334-6871,press
option2forCustomerService,orviae-mail[email protected]and
includethefollowinginformation:
•Name,addressandtelephonenumber
•Dateandplaceofpurchase
•Catalogandquantitypurchase
•Detaileddescriptionofproblem
AllreturnedproductsmustbeaccompaniedbyaReturnGoodsAuthorizationNumberissued
bytheCompanyandmustbereturnedfreightprepaid.AnyproductreceivedwithoutaReturn
GoodsAuthorizationNumberfromtheCompanywillberefused.
CooperLighting,LLCisnotresponsibleformerchandisedamagedintransit.Repairedor
replacedproductsshallbesubjecttothetermsofthiswarrantyandareinspectedwhen
packed.Evidentorconcealeddamagethatismadeintransitshouldbereportedatonceto
thecarriermakingthedeliveryandaclaimledwiththem.
ReproductionsofthisdocumentwithoutpriorwrittenapprovalofCooperLighting,LLCarestrictlyprohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected]
PrintedinChina
Oneormoreofthesepatentsmayapply,additionalpatentspending:6,175,309;5,381,323;D433,771;D431,092;D435,924;
D434,165;D374,496;D431,319
ARTÍCULOS NECESARIOS
(se compran por separado)
•Destornilladorencruz(Phillips)
•Calafateodesiliconaresistentealaintemperie
•(2)lámparasparaproyectortipoPAR38de100W(máximo)
NOTA:EsteaccesoriofuediseñadoparatrabajarconbombillasreectorasdeHalógenoPARde
150vatioscomomáximo.Paramayorecienciadeenergía,usebombillasreectoras
HalógenoPARdemenorvataje.Noserecomiendaelusodebombillasuorescentes
compactas(CFL)porquetienenparteselectrónicasquepuedeninterferirconlasfunciones
dedeteccióndemovimientodesuaccesorio.ParacumplirconlosrequerimientosdeENERGY
STAR®,lapotenciamáximadelabombillanodebeexceder250W.
CÓMO FUNCIONA
PIRfuncionamuybienenladeteccióndemovimientolateral
enunrangodedetecciónde270°.ElRadarDopplerPrecision
Plus™haceunexcelentetrabajodetectandomovimientode
acercamientoyalejamientodelaunidad.Lacombinaciónde
ambossistemasproporcionaprecisiónavanzadaycobertura
completadentrodelrangodedetección.Elmovimientodesde
cualquierdireccióndispararáelreector–inclusoentemperaturas
extremasdecaloryfrío.
ADVERTENCIAS Y PRECAUCIONES
•Leaestasinstrucciones.
•Guardeestasinstrucciones.
•Atiendatodaslasadvertencias.
•Sigatodaslasinstrucciones.
•Sóloparausoenexteriores.
•cULusparaubicacionesmojadas.
•Elportalámparasdebeestarconectadoaunafuentedeenergíade120Voltios,60Hz.
Cualquierotrotipodeconexiónanulalagarantía.
•Elportalámparasdebeserinstaladoporpersonasconexperienciaencableadodomésticoo
porunelectricistacalicado.Elsistemaeléctricoyelmétododeconexióneléctricadelporta-
lámparasdebecumplirconelCódigoeléctriconacionalyloscódigoslocalessobreedicios.
•Reemplacesiemprelabombillaconunadelmismovatiajeomásbajoqueelmarcado.Si
instalalámparasdemayorpotencia,puedecrearriesgodeincendio.Siusalámparasde
mayorpotencia,seanulalagarantía.(Utiliceunabombilladehalógenodeunmáximode
150W.)ParacumplirconlosrequerimientosdeENERGYSTAR®,lapotenciamáximadela
bombillanodebeexceder250W.
•Manténgaloalejadodeobjetosinamables.Nocoloqueelartefactoen
posicióndentrode1pulgada(2,5cm)decualquiermaterialcombustible.
•¡LabombillaseCALIENTArápidamente!
•Lalámparayelartefactosecalientanextremadamenteduranteeluso.Antesdeintentar
reposicionarelartefacto,dejequeseenfríetotalmente.
•Sidesarmaelartefacto,seanulalagarantía.
•Lalámparaespercableadaparafacilitarlainstalación.
•Utiliceconductoresdesuministroquesoportenunmínimode90°C.
•Instaleelartefactosobreunacajaeléctricaempotradaosupercialconconexiónatierra
marcadaparausarenlugareshúmedos.
•Nopermitaquelacabezadeldetectortoqueelalojamientodelalámpara-mantengapor
lomenos1/2˝(1,27cm)deespacioentreelaccesorioyeldetector.
•Sisereemplazaelvidrio,utilicesolovidriodeseguridadcompactadodeigualgrosor.
•Paraunfuncionamientoyprotecciónadecuadoscontraposiblesdaños,losbotonesde
ajustedelacabezadelsensordemovimientosedebenajustarendirecciónalpiso.
•Nouseesteaparatocercadeagua.
•Limpieúnicamenteconuntraposeco.
•Noobstruyalasaberturasdeventilación.Instaledeconformidadconlasinstrucciones
delfabricante.
•Noinstalecercadefuentesdecalortalescomoradiadores,rejillasdeairecaliente,estufas
uotrosaparatos(incluyendoamplicadores)queproduzcancalor.
•Useúnicamenteacoplamientos/accesoriosespecicadosporelfabricante.
•EstedispositivocumpleconlaParte15delasReglasdelaComisiónFederalde
Comunicaciones(FCC)delosE.U.deA.Laoperaciónestásujetaalasdoscondiciones
siguientes:(1)Estedispositivonopuedecausarinterferenciadañina,y(2)estedispositivo
debeaceptartodainterferenciarecibida,incluyendolainterferenciaquepuedacausarun
funcionamientoindeseado.SegúnlaParte15delasReglasdelaFCC,todocambioo
modicaciónaldetectordemovimientodescriptoenestahojadeinstruccionesqueno
estéexpresamenteaprobadoporCooperLighting,LLCpodríaanularlaautorizacióndel
usuarioparaoperarelequipo.
NOTA:Esteequipohasidoprobado,ysehavericadoquecumpleconloslímitesdeun
dispositivodigitalClaseB,deacuerdoconlaparte15delasReglasdelaFCC.Estoslímites
estándiseñadosandeproveerunaprotecciónrazonablecontralainterferenciadañina
enunainstalaciónresidencial.Esteequipogenera,usaypuedeirradiarenergíaderadio
frecuencia,ysinoseinstalayutilizadeacuerdoconlasinstrucciones,puedecausar
interferenciadañinaenlascomunicacionesderadio.Sinembargo,nosegarantizaqueno
ESPAÑOL
Hasta
90pies
270grados
Problem Cause / Solution
Lights Stay On At
Night And Do
Not Turn Off
Thereismotioninthedetectionzone.
• Makesurethesensorisnotpickingupmovingobjectssuchas
trees,trafc,etc.
• Reducethesensitivity.
• Repositionthesensor.
Unitisinoverridemode(ifthereisnomotion).
• TurnthelightswitchtotheOFFpositionfor90seconds,andthen
turnbacktotheONpostion.Thiswillsendtheunitbackintothe
motionactivatedsetting“Auto”.
*Ifthelightstaysonwiththesensorlenscovered,contact
customerservice.
Unitisinthe“Auto”mode.
•Makesuretheunitissetbetween1m-12m(“Auto”mode).
Lights
Continuously
Blink On And
Off At Night
Thelightgivenfromtheunit’sownlampisaffectingthe
motionsensor.
• Re-aimthelamp.
• Repositionmotionsensor.
MakesureknobisnotpositionedbetweenTESTand1m.
• Repositionknobclosertoselectedfunction,eitherTEST,or1m.
Lights Are On
During The Day
ThecontrolsonthebottomofthemotionsensorareintheTESTmode.
•RepositionMODEknoboffofTESTtoatimeselection(1m-12m).
Themotiondetectorisshadowed.
• Repositionmotionsensor.
Red LED Indicator
Light Comes ON
And OFF During
Daylight Hours
Duringdaylighthours,theredLEDindicatorwillashwhenmotion
isdetected.Thisisnormal.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

All-Pro MS276RD Operating instructions

Category
Work lights
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages