CONCORD Duo Owner's manual

Page is loading ...

0145-06

Um die Funktionsfähigkeit und Sicherheit Ihres Kinderauto-

sitzes auch nach einem Austausch von Ersatz- und Zube-

hörteilen zu gewährleisten, bitten wir Sie bei Bestellungen

Ihrem Fachhändler nachstehende Angaben mitzuteilen:

To ensure the maximum efficiency of your child car safety

seat after the exchange of the covers or spare parts ask

your retailer about following information:

Pour assurer une efficacité optimale de votre siège auto

après l‘échange de housses ou de pièces détachées,

demandez à votre détaillant l‘information suivante:

Per garantire la funzionalità e la sicurezza del vostro

seggiolino da auto per bambini anche dopo una

sostituzione di parti di ricambio o accessori, vi preghiamo

di comunicare al vostro negozio di fiducia specializzato

i seguenti dati al momento di emettere l‘ordine:

Para seguir garantizando el correcto funcionamiento y

la seguridad de su silla infantil para automóvil después

de un cambio de piezas o accesorios, le rogamos que

indique los siguientes datos al realizar pedidos a su

comercio especializado:

Para garantir a funcionalidade e a segurança da sua

cadeira de criança para automóvel após a substituição

de peças e acessórios, agradecemos que comunique

os seguintes dados ao seu distribuidor:

Om de functionaliteit en de veiligheid van het door u

gekochte autokinderzitje ook na vervanging van onder-

delen en accessoires te waarborgen, is het belanggrijk

dat u bij de bestelling in uw speciaalzaak onderstaande

gegevens vermeldt:

CONCORD

Industriestrasse 25

95346 Stadtsteinach

universal

- 18 kg

04..........

0000000

1

2

E

1

...........................................................................................

1

ECE-Nr. / ECE-no. / N˚ de série / N˚ ECE / Número ECE

..........................................................................................

2

Serien-Nr. / serial-no. / N˚ di serie / Número de serie

............................................................................................

Ersatzteil / Seat type / Type de siège / Parte di ricambio / Pieza de repuesto

/Peça / Type kinderzitje

............................................................................................

Fachhändler / Dealer / Commerçant spécialisé / Negozio specializzato /

Comercio especializado / Distribuidor / Speciaalzaak

..........................................................................................

.............................................................................................

...........................................................................................

Meine Anschrift / my address / Mon adresse / Il proprio indirizzo / Mi

dirección / Meu endereço / Mijn adres

CONCORD

ULTIMAX

con0145-4-06-Ultimax-MA-Bestell

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: Bestellseite

Maßstab: gez.: 03.05.04 ps

geänd am 06.05.04 ps / 07.06.04 ps / 01.07.04 ps / 05.04.05 ps / 16.03.06

ps / 07.06.06 ps

Page is loading ...

Using the ULTIMAX child car seat

0236-02

To safeguard your child you have

opted for our CONCORD

ULTIMAX seat. This product is

manufactured under strict quality

controls. Its excellent safety

features work best when the seat

is used in accordance with legal

requirements. Be sure, therefore,

to comply fully with the

instructions for its installation and

use.

The ULTIMAX is suitable for

infants from birth up to 18 kg or

for children up to the age of

approx. 4 years. The seat may

be used on all seats in your car

fitted with a three-point seat belt.

On the basis of accident

statistics, we recommend using

the seat behind the passenger

seat.

The child car seat comprises

three parts: seat shell (A), base

unit (B) and

reboard wedge (C).

The seat can also be engaged

in four different seat positions

when facing forwards and in one

position when rear-facing.

The seat shell must not be

removed while the child is still

seated in it.

Summary of contents:

1. Rear-facing installation (from

birth to 13 kg).

2. Front-facing installation (from

9 to 18 kg).

3. Securing the child.

4. Adjusting the head support /

adjusting the seat to the

child’s size.

5. Releasing and removing the

seat.

6. Removing the cover /

removing the pelvic insert.

7. Care instructions

8. Important information

9. Warranty terms

10. General information

A

B C

0106-02

con0236-4-02-Ultimax-MA-Inhalt

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: Inhaltsverzeichnis - GB

Maßstab: gez.: 13.04.04 ps

geänd am 20.04.04 ps / 28.04.04 ps / 29.04.04 ps / 07.06.04 ps / 23.12.04 tk /

31.03.05 ps

2

1

1. Rear-facing installation (from birth to 13 kg)

0237-02

Important!

Do not use on seats

with airbags.

Extreme danger!

Turn the rotary handle at the front

of the seat shell upwards (1) and

at the same time push the seat

shell into the upright position (2).

Hold the seat shell with your

thumbs on the left and right side

and use your fingers to pull the

grey levers as far as they will go

in the direction of the arrow. Keep

the levers extended and lift the

seat shell upwards and out until

the green component is visible

above the snap mechanism.

Then release the levers and

remove the seat shell.

Insert the base unit into the car

seat as illustrated.

Position the reboard wedge

(green) as shown.

0014-07 0017-06 0013-04

A

I

R

B

A

G

con0237-4-02-Umax-GB-MA-Kap.1

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel1-GB

Maßstab: gez.: 25.05.04 ps

geänd am 07.06.04 ps / 31.03.05 ps

1.2 1.31.1

click

1. Rear-facing installation (from birth to 13 kg)

0238-01

Pass the car seat belt over the

top of the base unit and secure

the belt in the buckle.

Position the lower belt section

(1) (lap belt) under the blue lap

belt guides (see illustration). Pass

the upper belt section (2)

(diagonal belt) around the outside

of the base unit and insert it into

the blue belt clip. Tension the

belt as shown in the illustration,

and close the blue belt clip.

0101-03 0028-05

2

1

con0238-4-01-Umax-GB-MA-Kap.1

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel1-GB

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

1.51.4

1. Rear-facing installation (from birth to 13 kg)

0239-01

Wrong belt positioning!

Belt positioning when the base unit

is installed correctly.

con0239-4-01-Umax-GB-MA-Kap.1

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel1-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

1.6

0119-06

1.7

0118-04

1. Rear-facing installation (from birth to 13 kg)

0240-02

Hold the seat shell as illustrated

and position it on the base unit.

Press the seat shell downwards

until it clicks audibly into position.

Always check that when the seat

shell is inserted a green dot is visible

on both sides through the opening

on the sidepieces. This indicates

that the seat is installed correctly.

When rear-facing the seat may

only be used in the upright

position! If the child’s body weight

exceeds 8 kg, the factory-fitted

pelvic insert should be removed,

see section 6.5.

Disassembly is done in the

reverse order.

click

0088-08

con0240-4-02-Umax-GB-MA-Kap.1

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel1-GB

Maßstab: gez.: 24.05.04 ps

geänd am 07.06.04 ps / 31.03.05 ps

1.91.8

0090-06

2

1

2. Front-facing installation (from 9 to 18 kg)

0241-01

Important!

Front-facing installation is only

suitable from a body weight of

9 kg and without the pelvic

insert, see section 6.5!

Turn the rotary handle at the front

of the seat shell upwards (1) and

push the seat shell into the

upright position (2).

Hold the seat shell with your

thumbs on the left and right side

and use your fingers to pull the

grey levers as far as they will go

in the direction of the arrow. Keep

the levers extended and lift the

seat shell upwards and out until

the green component is visible

above the snap mechanism.

Then release the levers and

remove the seat shell.

Insert the base unit into the car

seat as illustrated. Position the

reboard wedge (green) as

shown.

0014-07 0017-06 0010-04

con0241-4-02-Umax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 24.05.04 ps

geänd am 07.06.04 ps / 31.03.05

2.2 2.32.1

click

2. Front-facing installation (from 9 to 18 kg)

0242-01

Pass the car seat belt over the

top of the base unit and secure

the belt in the buckle.

Insert the lower belt section (lap

belt) into the lap belt guides (red)

as illustrated.

Open the red belt clip on the belt

tensioner.

0030-04 0031-05 0032-05

con0242-4-01-Umax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

2.5 2.62.4

2. Front-facing installation (from 9 to 18 kg)

0243-02

Turn the open side of the ratchet

shaft upwards.

Position the upper belt (diagonal

belt) in the opening of the ratchet

shaft and into the guide

mechanism behind it.

The belts must not be twisted!

0029-08 0037-09

con0243-4-02-Umax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 25.05.04 ps

geänd am 07.06.04 ps / 31.03.05 ps

2.82.7

1

2

2. Front-facing installation (from 9 to 18 kg)

0244-01

Tighten the upper belt (1) slightly

and close the red belt clip (2).

Then tighten the belt once again.

Use the ratchet to wind the belt

up until the base unit is firmly

secured in the car seat.

The belt must be taut.

The base unit must be

positioned straight on the car

seat, parallel to the direction

of travel. Move the base unit

to adjust if necessary and then

tighten the belt again.

The car safety belt must be

threaded through all three belt

guides.

0039-07 0041-07 0069-08

con0244-4-01-Umax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

2.10 2.112.9

2. Front-facing installation (from 9 to 18 kg)

0245-01

Belt positioning when the base

unit is installed correctly.

The buckle for the vehicle safety

belt must not come above the

edge of the lap belt guide.

If in doubt or if you are still

uncertain, please contact

CONCORD.

0121-030073-05

con0245-4-01-Ultimax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

2.12 2.13

2. Front-facing installation (from 9 to 18 kg)

0246-00

Always check that when the seat

shell is inserted a green dot is

visible on both sides through

the opening on the side pieces.

This indicates that the seat is

installed correctly.

Disassembly is done in the

reverse order (see 1.1 and 1.2).

To release the belt tensioner see

Chapter 5.

click

0048-09

con0246-4-01-Ultimax-GB-MA-Kap.2

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel2-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

2.152.14

0050-07

Hold the seat shell as illustrated

and position it on the base unit.

Press the seat shell downwards

until it clicks audibly into position.

3. Securing the child

0247-00

Open the belt buckle and open

the child seat belts outwards to

lie on the armrests. Then put the

child into the seat shell so that

its back rests against the

backrest.

The central adjuster is located at

the front of the seat, beneath the

cover. This secures the central

belt.

Release the central adjuster by

pushing the small flap up (see

illustration), and then pull the belt

forwards (do not pull on the belt

padding!).

0056-060036-06

con0247-4-01-Umax-GB-MA-Kap.3

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 3-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

3.1 3.2

3. Securing the child

0248-01

Tension the belt system by pulling

the belt of the central adjuster

until your child is securely

strapped in. Please check that

both the shoulder and lap belts

are tensioned equally. To take

the child out, press the red

“Press” button on the belt buckle

of the harness system.

Fit both belt parts together (see

illustration) and push them into

the belt buckle so that they

engage with an audible “click”.

0059-050058-06

click

con0248-4-01-Umax-GB-MA-Kap.3

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 3-GB

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

3.3 3.4

4. Adjusting the seat to the child’s size / adjusting the head support and harness

0249-03

Grasp the head support at the

top and pull it forwards. You can

then set it to the height that is

right for your child. There are six

possible different positions.

Attention! Always make sure

the belt is positioned correctly,

as shown in 4.2, illustration

(A).

When the child is strapped in,

the shoulder belt should feed

horizontally to the back or incline

slightly upwards, see illustration

(A). If the shoulder belt feeds

downwards as shown in the

illustration (B), then the belt must

be repositioned and inserted

through the next slot up.

To do this proceed as follows:

To adjust the shoulder belt

positions, the seat shell must

be removed from the base unit

(see 1.1 and 1.2)!

Pull away the back trim located

on the back of the seat shell.

A

B

0033-05 0105-04 0034-02

con0249-4-03-Umax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 4-GB

Maßstab: gez.: 24.05.04 ps

geänd am 28.05.04 ps / 31.03.05 ps / 07.06.06 ps

4.1 4.2 4.3

4. Adjusting the seat to the child’s size / adjusting the head support and harness

0250-02

On the rear of the seat shell,

separate the two belts from the

connecting piece.

0036-06

con0250-4-01-Umax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel4-GB

Maßstab: gez.: 25.05.04 ps

geänd am 31.03.05 ps

4.54.4

0040-04

The central adjuster is located at

the front of the seat, beneath the

cover. This secures the central

belt.

Release the central adjuster by

pushing the small flap up (see

illustration), and then pull the

belts through to the front (do not

pull on the belt padding!).

4. Adjusting the seat to the child’s size / adjusting the head support and harness

0251-01

Then pull the two belts out to the

front through the backrest and

the seat cover.

Now thread both belts from the

front through the cover and into

the required slot.

On the back you must thread

both belts back into the

connecting piece, then tighten

the belt at the front by the central

belt.

Please check that the left and

right harness belts are both

adjusted in the same way.

Pull the two metal clasps on the

back of the seat out of their

recesses and fit them through

the belt openings in the seat shell.

0042-070123-04

con0251-4-01-Umax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 4-GB

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

4.74.6

4. Adjusting the seat to the child’s size / adjusting the harness / shortening the belts

0252-02

0143-04

0124-03

click

con0252-4-02-Ultimax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 4-GB

Maßstab: gez.: 24.05.04 ps

geänd am 07.06.04 ps / 31.03.05 ps

4.8

When does the belt system

need to be shortened?

If you cannot tighten the child

seat belt sufficiently by pulling on

the central adjuster at the front

of the seat, then it will be

necessary to shorten the belt

system.

To do this proceed as follows:

4.9

On the back of the seat, clip the

metal clasps back into position.

They must engage with an

audible “click”.

Thread the belts back into the

connecting piece, as shown in

the illustration.

Finally, clip in the back trim.

4. Adjusting the seat to the child’s size / shortening the belts

0253-01

Remove the seat shell from the

base unit and lay the shell upside

down on a clean surface.

Release the elastic tapes on the

cover and pull the cover back a

little. Lever out the metal clasps

secured on the bottom of the

shell, and thread them through

the large side opening and the

small slot (see illustration).

Now press the metal clasps from

the outside into the recess.

Both sides must be adjusted

equally!

0045-05 0051-06

con0253-4-01-Umax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 4

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

4.10 4.11

click

4. Adjusting the head support / adjusting the seat to the child’s size

0254-01

When does the shortened belt

system need to be returned to

its lengthened setting?

If, after releasing the child seat

belt by means of the central

adjuster, it does not pull forwards

sufficiently to allow the belt

system to be closed, then the

belt system needs to be

lengthened.

To do this proceed as follows:

Remove the seat shell from the

base unit and lay the shell upside

down on a clean surface.

Release the elastic tapes on the

cover and pull the cover back a

little. Lever out the metal clasps

secured on the side of the shell

and push them back through their

slots.

Now press the metal clasps from

the outside into the recess. The

clip must engage with an audible

“click”.

Both sides must be adjusted

equally!

0104-04 0053-06 0054-06

con0254-4-01-Umax-GB-MA-Kap.4

Disk 01-01A Concord

Artikel: Ultimax

Bezeichnung: MA-Kapitel 4-GB

Maßstab: gez.: 24.05.04 ps

geänd am 31.03.05 ps

4.12 4.13 4.14

Page is loading ...

CONCORD Duo Owner's manual

This manual is also suitable for

CONCORD Duo Owner's manual

in other languages

Related papers

Other documents