HeathZenith HZ-4300-BK User manual

FEATURES

• Lightcomesonwhenmotionisdetected.

• Automaticallyturnslightoff.

• HalfpowerAccentlighting.

• Photocell keeps the light off during daylight

hours.

REQUIREMENTS

• Thelightcontrolrequires120voltsAC.

• IfyouwanttouseManualMode,thecontrolmust

bewiredthroughaswitch.

• Some electrical codes require installation by

a qualiﬁed electrician.

Diecast Motion

Sensing Porch Light

Thispackageincludes:

• PorchLight

• EasytouseUniversalMountingBracket

• MountingHardware

• WireNuts

• LensShield

Model4300

©2012HeathCoLLC 204062-01A

Mode: On-Time Works: Day Night

Test 5Seconds  x x

Auto/ 1,5,or10minutes   x

AccentOff,3,6Hr,toDawn   x

Manual UntilDawn*   x

OPERATION

Note: Whenrstturnedonwaitabout1

1

/

2

minutes

forthecircuitrytocalibrate.

*resetstoAutoModeatdawn.

ON-TIME

TEST 1 510MIN

TEST

SetON-TIMEswitchto

1,5,or10minutes.

AUTO

ON-TIME Switch at 1, 5, or

10 minutes

...backon.

1Second

OFFthen...

Manual mode only works at

nightbecausedaylightreturns

thesensortoAUTO.

Flipthelightswitchoffforone

secondthenbackontotoggle

betweenAUTOandMANUAL

MODE.

Manualmodeworksonlywith

theON-TIMEswitchinthe1,

5,or10position.

MODE SWITCHING SUMMARY

Flip light switch off

for one second then

back on*

*Ifyougetconfusedwhileswitchingmodes,turnthe

poweroffforoneminute,thenbackon.Afterthecali-

brationtimethecontrolwillbeintheAUTOmode.

MANUAL MODE

AUTO

TEST

MANUAL MODE

ON-TIME

TEST 1 5 10 MIN

Before installation, record the model number

listed inside the ﬁxture. Attach receipt in case

of possible warranty issues.

Model Number:

SettheON-TIMEswitch

onthesensortoTEST.

2

204062-01

DUAL BRITE

®

ON-TIME

TEST 1 5

1

0 MIN

OFF 3 6

DUSK

TO DAWN

DUAL BRITE

®

ON-TIME

TEST 1 5 10 MIN

OFF 3 6

DUSK

TO DAWN

INSTALL UNIVERSAL MOUNTING

BRACKET

Forbestperformance,mountthextureatleast

8feet(2.4m)abovetheground.

FixtureScrew(Tightened

FingerTight)

JunctionBox

UniversalMounting

Bracket

JunctionBoxScrew

WIRING LIGHT FIXTURE

1. Connectthejunctionboxwiresandthexture

wirestogetherasshowninthefollowingdia-

grams.

CAUTION: DO NOT remove wire connec-

tor from RED wire or connect the RED wire

unless you want to control other lights from

this motion sensor ﬁxture.

DISASSEMBLE LIGHT FIXTURE

1. Removetwodecorativenutsfromlightxture

cover.

2. Removecoverfrombase.

3. Removetwodecorativenutsfromxturescrews

inuniversalmountingbracket.

4. Remove universal mounting bracket from

base.

DecorativeNut

LightFixtureBase

LightFixtureCover

DecorativeNut

Universal

Mounting

Bracket

Note:Ifyouhaveametaljunctionboxusetherecom-

mendedgroundingmethodshowninthefollowing

illustration.Ifyouareuncertainaboutthegrounding

method,consultyourlocalbuildingcode.

2. Twistandsecurewireswithwirenuts.

DualBrite

®

DIMMER CONTROL

Lightcomesonhalfbrightforselectedtimeafterdusk

(Off,3hr.,6hr.,untildawn).SelectingOFFdisablesthis

feature.Themotionsensingfeatureswillcontinueto

workasdescribedinthismanual.Ifmotionissensed,

thelightturnsonfullbrightfortheON-TIME(1,5,or

10minutes)thenreturnstodimmode.

WARNING: Turn power off at circuit

breaker or fuse.

1. Tightenthetwoxturescrewsngertight.

2. Attachuniversalmountingbrackettojunction

boxsecurelywiththetwoscrewsprovided.

3

204062-01

GroundScrew

WhitetoWhite

BlacktoBlack

Recommended Grounding Method

One Motion Sensing Light

Two Motion Sensing Lights (Working Independently)

Other Wiring Options

Thisxturecanbewiredtocontrolanotherstandard

ormotionsensinglightxture(s).Seethefollowing

wiringdiagramsforproperconnections.

Note:Allwiringshouldberuninaccordancewith

the National Electrical Codethroughconduit or

anotheracceptablemeans.Contact a qualiﬁed

electrician if there is any question as to the

suitability of the system.

BlacktoBlack

WhitetoWhite

Ground

toGround

BlacktoBlack

WhitetoWhite

GroundtoGround

MetalJunction

Box

Pigtail(not

supplied)

FixtureBare

GroundWire

BareGroundWire

Wiring Motion Sensing Light to Control Standard

Fixture

Groundto

Ground

StandardLightFixtureMotionSensingLight

BlacktoBlack

WhitetoWhite

RedtoBlack

Maximum Load for

Motion Sensor –

200 Watts

Maximum Lamp

Wattage Rating

for Light Fixture –

100 Watts

Maximum Lamp

Wattage Rating

for Light Fixture –

100 Watts

TOTAL Load for

Motion Sensor –

200 Watts

CONTROLLING Fixture

CONTROLLED Fixture 1

Whencontrollinganadditionallightxture(s),the

maximumwattageofthemotionsensoron this

xtureshouldbeobserved.Seeillustrationbelow

foranexampleofamaximumlampwattageload

calculation.

IMPORTANT: When determining the maximum

lampwattageratingofthexturetobecontrolled,

refertothemaximumlampwattagelabelonthe

xtureandnotthewattageratingonthelamp(s)

currentlyinstalledinthexture.

Wiring Motion Sensing Light to Control Another

Motion Sensing Light

BlacktoBlack

WhitetoWhite

GroundtoGround

BlacktoRed

and Black

RedtoBlack

ControlledMotion

SensingLight

MotionSensingLight

4

204062-01

TESTING

1. Turn on the circuit breaker and light switch.

Note:Sensorhasa1

1

/

2

minutewarmupperiod

beforeitwilldetectmotion.Whenrstturnedon

wait1

1

/

2

minutes.

2. SettheON-TIMEswitchtotheTESTposition

andtheDualBrite

®

switchtotheOFFposition.

3. Walkthroughthecoverageareanotingwhere

youarewhenthelightsturnon.InTESTmode,

lightwillstayonforonly5secondsthenturn

off.

4. AdjusttheSENSITIVITYtoincreaseordecrease

therangeasneeded.Toomuchsensitivitymay

causefalsetriggeringduetoheatsourcesinthe

coverage area (see Adjustment of Coverage

AreaorTroubleshootingsection).

Itisalsopossibletowiretwomotionsensinglights

sothateitherunitwillturnonbothlightsatthesame

time(dualcontrolledsystem).Itisrecommendedthat

onlypeoplewithelectricalwiringexperienceattempt

thisconguration.Pleasecallourcustomerservice

number (1-800-858-8501) before attempting this

wiring.If the dual controlled wiring is not done

correctly, it can destroy both motion sensing

ﬁxtures and void your warranty.

INSTALL FIXTURE BASE TO

JUNCTION BOX

1. Pushwiresintothejunctionbox.

2. Slide lightxture base onto xture screwsand

tightendecorativenutssnuglyagainstthebase.

3. Install four candelabra base light bulbs (25

Watts maximum each).

4. Refer to TESTING section before installing

cover.

5. Afterswitchesaresetandtestingiscomplete,

usethe2decorativenutstoinstallthecover.

DUAL BRITE

®

ON-TIME

TEST 1

5 10 MIN

OFF 3 6

DUSK

TO DAWN

DualBrite

®

ON-TIME

DUSK

OFF

3

HR 6HR TO DAWN

TEST 1 5 10 MIN

Sensor

Lens

5. SettheamountofON-TIMEyouwantthelight

tostayonaftermotionisdetected(1,5,or10

minutes).

6. Settheamountoftimeyouwantthelightto

stayonintheAccentmode(Off,3hours,6

hours,ordusk-to-dawn).

SENSITIVITY

+

–

+

–

SENSITIVITY

DUAL BRITE

®

ON-TIME

TEST 1

5 10 MIN

OFF 3 6

DUSK

TO DAWN

FixtureScrew

JunctionBox

DecorativeNut

25WattCandelabra

BaseBulb

Maximum Range Coverage Angle*

(Top View)

360°

30Feet(9.1m)

inallDirections

*Withoutlensshieldinstalled.

8ft.(2.4m)

5

204062-01

Least Sensitive Most Sensitive

The sensor is less sensitive to motion directly

towardsit and moresensitive to motion across

coveragearea.

Sensor

Motion

SPECIFICATIONS

Range...........................Upto30ft.(9.1m)

[varieswithsurrounding

temperature].

SensingAngle.............. 360°

ElectricalLoad..............Upto100Watt

MaximumTungsten

Incandescent(Upto25

WattMaximumeach

lampholder).

BulbType...................... CandelabraBase,Type

“B”,25WattMaximum

SensorCapacity...........Upto200Watt(1.7A.)

MaximumTungsten

Incandescent

PowerRequirements.... 120VAC,60Hz

OperatingModes..........TEST,AUTO/ACCENT,

andMANUALMODE

ON-Timer......................1,5,10minutes

DualBrite

®

Timer..........Off,3,6Hrs,Dusk-to-

Dawn

HeathCo LLC reserves the right to discontinue

productsandtochangespecicationsatanytime

withoutincurringanyobligationtoincorporatenew

featuresinproductspreviouslysold.

ADJUSTMENT OF COVERAGE

AREA

Thesensor onthis light xturedetects“motion”

bythemovementofheat(bodyheat)acrossthe

coveragearea.However,followingareexamples

ofobjectsthatalsoproduceheatandcancause

thesensortofalsetrigger:

•PoolsofWater •AirConditioners

•DryerVents •Fenced-InAnimals

•HeatingVents •AutomobileTrafc

Ifyoususpectthataheatsourceofthistypeisfalsely

triggeringthesensorandreducingthesensitivity

does not solve the problem, then a lens shield

(included)can be installed.Theplasticlensshield

isdividedinto6sections.Eachsectionwillreducethe

coverageangleby30degrees.Also,thetipofeach

sectionmaybe removedtochange the effective

rangeofthesensor.

1. Break off the

amountoflens

shield needed

toblockthede-

sired area of

coverage.

2. Cut desired

amountoffoam

tapeneededto

adherethelens

shieldtothesensorlens.

3. Removepaperbackingfromonesideofcut

foamtapeandadherefoamtapetoinsideof

lensshield.

4. Removepaperbackingfromothersideofcutfoam

tapeandadherelensshieldtosensorlens.

5. Retesttoconrmthatthesensorisnolonger

falsetriggering.

Note:To help determine amount of lens shield

required,applysmallsectionsoneatatime.Ad-

ditionalsectionscanbeappliedifnecessary.

Area

Blocked

Area

Blocked

Lens

Shield

Lens

Shield

Portion

Removed

Effective

CoverageArea

(TopView)

LensShield

SensorLens

DUAL BRITE

®

ON-

TIME

TEST 1 5 10 MIN

OFF 3 6

DUSK

TO DAWN

6

204062-01

SYMPTOM

Light stays on

continuously.

Light ﬂashes on

and off.

Light does not

stay on in Man-

ual mode.

POSSIBLE CAUSE

1.

Thereisaheatsourcelikeanair

vent,dryervent,orbrightly-painted,

heat-reectivesurfaceinthecover-

agearea.(Install shield on sensor

in the direction of heat source.)

2. LightcontrolisinManualMode.

(Switch to Auto.)

3. Light control is in DualBrite

®



mode.

4. Sensitivityissettoohigh.(Reduce

sensitivity.)

1. SensorisintheTestmode.(While

in TEST mode, light only stays on

for 5 seconds.)

1. Nearbylarge,light-coloredobjects

reecting light may trigger the

shut-offfeature.Donotpointother

lightsatthesensor.

POSSIBLE CAUSE

1. Lightswitchisturnedoff.

2. Bulbsarelooseorburnedout.

3. Fuseisblownorcircuitbreaker

isturnedoff.

4. Daylightturn-offisineffect(re-

check after dark).

5. Incorrectcircuitwiring,ifthisis

anewinstallation.

1. Sensor may be installed in a

relativelydarklocation.

2. Sensor is in Test. (Set control

switch to an ON-TIME position.)

1. Sensor may be sensing small

animals or automobile traffic.

(Reduce sensitivity.)

SYMPTOM

Light will not

come on.

Light comes on

in daylight.

Light comes on

for no apparent

reason.

TROUBLESHOOTING GUIDE

TWO YEAR LIMITED WARRANTY

Thisisa“LimitedWarranty”whichgivesyouspeciclegalrights.Youmayalsohaveotherrightswhichvaryfromstateto

stateorprovincetoprovince.

Foraperiodoftwoyearsfromthedateofpurchase,anymalfunctioncausedbyfactorydefectivepartsorworkmanship

willbecorrectedatnochargetoyou.

Not Covered - Repairservice,adjustmentandcalibrationduetomisuse,abuseornegligence,lightbulbs,batteries,and

otherexpendableitemsarenotcoveredbythiswarranty.Unauthorizedserviceormodicationoftheproductorofany

furnishedcomponentwillvoidthiswarrantyinitsentirety.Thiswarrantydoesnotincludereimbursementforinconvenience,

installation,setuptime,lossofuse,unauthorizedservice,orreturnshippingcharges.

ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnotextendedtootherequipmentandcomponentsthat

acustomerusesinconjunctionwithourproducts.

THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRANTIES,EXPRESSORIMPLIED,INCLUDINGANY

WARRANTY,REPRESENTATIONORCONDITIONOFMERCHANTABILITYORTHATTHEPRODUCTSAREFITFOR

ANYPARTICULARPURPOSEORUSE,ANDSPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,OR

CONSEQUENTIALDAMAGES.

REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMERANDTHERESHALLBENOLIABILITY

ONTHEPARTOFHEATHCOLLCFORANYSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGES,

INCLUDINGBUTNOTLIMITEDTOANYLOSSOFBUSINESSORPROFITS,WHETHERORNOTFORESEEABLE.Some

statesorprovincesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sotheabovelimita-

tionorexclusionmaynotapplytoyou.Please keep your dated sales receipt, it is required for all warranty requests.

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning

product to store.

Ifyouexperienceaproblem,followthisguide.YoumayalsowanttovisitourWebsiteat:www.hzsupport.

com.Iftheproblempersists,call*forassistanceat1-800-858-8501(Englishspeakingonly),8:00AMto

5:00PMCST(M-F).Youmayalsowrite*to:

HeathCoLLC

P.O.Box90045,BowlingGreen,KY42102-9045

ATTN:TechnicalService

*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:ModelNumber,Dateof

Purchase,andPlaceofPurchase.

No Service Parts Available for this Product

Page is loading ...

HeathZenith HZ-4300-BK User manual

Related papers

Other documents