Toro TimeCutter SWX 4250 Riding Mower User manual

SERVICE MANUAL

Time Cutter SW/SWX

Residential Products

ABOUT THIS MANUAL

This service manual was written expressly for Toro service technicians. The Toro Company has made every effort to

make the information in this manual complete and correct.

Basic shop safety knowledge and mechanical/electrical skills are assumed. The Table of Contents lists the systems

and the related topics covered in this manual.

For service information on drive systems, please refer to the Hydro-Gear ZT-2800/ZT-3100/ZT-3400 service manual

(BLN 52441) and the Hydro-Gear ZT-2100/ZT2200 EZT service manual (492-4778). For information specic to the

engines used on this unit, refer to the appropriate engine manufacturer’s service and repair instructions.

Toro TimeCutter® SW and Toro TimeCutter® SWX are covered in this manual. The manual may also be specied for

use on later model products.

The hydrostatic transaxle is a sophisticated piece of machinery. Maintain strict cleanliness control during all stages of

service and repair. Cover or cap all hose ends and ttings whenever they are exposed. Even a small amount of dirt or

other contamination can severely damage the system.

If you have any questions or comments regarding this manual, please contact us at the following address:

The Toro Company

Residential and Landscape Contractor Service Training Department

8111 Lyndale Avenue South

Bloomington, MN 55420

The Toro Company reserves the right to change product specications or this manual without notice.

TABLE OF CONTENTS

TOC-6 Toro TimeCutter SS/MX/ZS Service Manual

THIS PAGE INTENTIONALLY LEFT BLANK.

TABLE OF CONTENTS

TOC-1Toro TimeCutter SS/MX/ZS Service Manual

1 - Safety Information

General Information ..................................................................................................................................... 1-1

Think Safety First......................................................................................................................................... 1-1

2 - Specications

2015 TimeCutter SW Specications ............................................................................................................ 2-1

Engine Specications .................................................................................................................................. 2-3

Hydro-Gear EZT, ZT-2100, ZT-2200 Hydrostatic Transaxles ...................................................................... 2-4

Checking the Hydraulic Oil Level

.......................................................................................................... 2-4

Hydro-Gear ZT-2800 Hydrostatic Transaxles .............................................................................................. 2-5

Checking the Hydraulic Oil Level .......................................................................................................... 2-5

Torque Specications .................................................................................................................................. 2-6

Standard Torque for Dry, Zinc Plated & Steel Fasteners (Inch Series) ....................................................... 2-7

Standard Torque for Dry, Zinc & Steel Fasteners (Metric Fasteners) .......................................................... 2-8

Other Torque Specications ........................................................................................................................ 2-9

Equivalents & Conversions........................................................................................................................ 2-10

Decimal & Millimeter Equivalents ........................................................................................................ 2-10

U.S. to Metric Conversions ..................................................................................................................2-11

3 - Chassis

Model & Serial Number Identication .......................................................................................................... 3-1

Grease & Lubrication Point.......................................................................................................................... 3-1

Front Axle / Caster Fork / Bearing Service .................................................................................................. 3-2

Font Axle / Caster Fork / Bearing Disassembly .................................................................................... 3-2

Front Axle / Caster Fork / Bearing Assembly ........................................................................................ 3-2

Castor Wheel / Bushing Service .................................................................................................................. 3-3

Castor Wheel / Bushing Disassembly ................................................................................................... 3-3

Castor Wheel / Bushing Assembly ........................................................................................................ 3-3

Front Axle Assembly Service ....................................................................................................................... 3-4

Front Axle Assembly Removal .............................................................................................................. 3-4

Front Axle Assembly Installation ........................................................................................................... 3-4

Pod / Fender / Fuel Tank Service ................................................................................................................ 3-5

Pod / Fender Removal - RH .................................................................................................................. 3-5

Pod / Fender Installation - RH ............................................................................................................... 3-5

Pod / Fender Removal - LH .................................................................................................................. 3-6

Pod / Fender Installation - LH ............................................................................................................... 3-6

Fuel Tank Removal ............................................................................................................................... 3-7

Fuel Tank Installation ............................................................................................................................ 3-7

Seat Pivot Service ....................................................................................................................................... 3-8

Seat Pivot Removal .............................................................................................................................. 3-8

Steering Column .......................................................................................................................................... 3-9

Front Shroud ....................................................................................................................................... 3-10

Front Shroud Removal .........................................................................................................................3-11

Front Shroud Installation ..................................................................................................................... 3-13

Pod / Fender Support Service ................................................................................................................... 3-15

Pod / Fender Support Removal (SWX Shown) ................................................................................... 3-15

Pod / Fender Support Installation ....................................................................................................... 3-15

Rear Bumper Service ................................................................................................................................ 3-16

Rear Bumper Removal ....................................................................................................................... 3-16

Rear Bumper Installation .................................................................................................................... 3-16

Upper Deck Lift Service ............................................................................................................................. 3-17

TABLE OF CONTENTS

TOC-2 Toro TimeCutter SS/MX/ZS Service Manual

Upper Deck Lift Removal ........................................................................................................................3-17

Upper Deck Lift Installaton ......................................................................................................................3-17

Deck Lift Exploded View .........................................................................................................................3-18

Lower Deck Lift Service ................................................................................................................................. 3-19

Lower Deck Lift Removal ........................................................................................................................3-19

Lower Deck Lift Installation .....................................................................................................................3-19

Deck Lift Exploded View .........................................................................................................................3-20

Return to Neutral Assembly ........................................................................................................................... 3-21

Return to Neutral Assembly Exploded View............................................................................................3-21

Return to Neutral Assembly Removal .....................................................................................................3-22

Return to Neutral Assembly Installation ..................................................................................................3-23

Speed Control Assembly Exploded View ......................................................................................................3-24

Speed Control Assembly Cable Adjustment ...........................................................................................3-25

Speed Control Assembly Cable Removal ...............................................................................................3-26

Speed Control Assembly Cable Replacement ........................................................................................3-27

Speed Control Assembly Removal .........................................................................................................3-29

Speed Control Assembly Installation ......................................................................................................3-30

Steering System Alignment Exploded View ...................................................................................................3-32

4 - Engine

Engine Replacement .......................................................................................................................................4-1

PTO Clutch & Clutch Stop Mounting (All Models) ..................................................................................... 4-1

Chassis Identication ................................................................................................................................4-1

Engine Mounting - Toro Engine ................................................................................................................. 4-2

Engine Mounting - Kohler Eingle Cylinder Engine ....................................................................................4-3

Engine Mounting - Kawasaki Twin Cylinder ..............................................................................................4-4

Engine Mounting - Kohler Twin Cylinder ...................................................................................................4-5

Engine Removal ........................................................................................................................................ 4-6

Engine Installation ..................................................................................................................................... 4-6

Clutch & Clutch Stop Location - Wide Frame ...........................................................................................4-7

Clutch & Clutch Stop Location - Narrow Frame ........................................................................................4-7

5 - Hydrostatic Drive System

Chassis Identication.......................................................................................................................................5-1

Wide Frame ..............................................................................................................................................5-1

Narrow Frame ...........................................................................................................................................5-1

Hydrostic Drive Exploded View .......................................................................................................................5-1

Wide Frame ..............................................................................................................................................5-1

Narrow Frame ...........................................................................................................................................5-1

Hydrostic Drive Belt Routing............................................................................................................................5-2

Tracking Adjustment ........................................................................................................................................5-3

Purging Procedure...........................................................................................................................................5-5

Hydrostatic Drive Belt Replacement ................................................................................................................ 5-6

Hydrostatic Drive Belt Removal ................................................................................................................5-6

Hydrostatic Drive Belt Installation .............................................................................................................5-7

Transaxle Replacement ................................................................................................................................... 5-7

Transaxle Removal ...................................................................................................................................5-7

Transaxle Installation ..............................................................................................................................5-11

TABLE OF CONTENTS

TOC-3Toro TimeCutter SS/MX/ZS Service Manual

6 - Mower Deck

Mower Deck Exploded View ............................................................................................................................6-1

32 in. Stamped Deck ................................................................................................................................. 6-1

42 in. Stamped Deck ................................................................................................................................. 6-2

42 in. Fabricated Deck ..............................................................................................................................6-3

50 in. Stamped Deck ................................................................................................................................. 6-4

50 in. Fabricated Deck ..............................................................................................................................6-5

PTO Belt Replacement and Belt Routing ........................................................................................................6-6

32 in. Stamped Deck ................................................................................................................................. 6-6

42 in. Stamped Deck

................................................................................................................................. 6-6

42 in. Fabricated Deck ..............................................................................................................................6-7

50 in. Stamped Deck ................................................................................................................................. 6-7

50 in. Fabricated Deck ..............................................................................................................................6-8

Inspecting the Belts .........................................................................................................................................6-8

PTO Belt Replacement ....................................................................................................................................6-8

Mower Deck Replacement ..............................................................................................................................6-9

Mower Deck Removal ...............................................................................................................................6-9

Mower Deck Installation ..........................................................................................................................6-10

Spindle Exploded View ..................................................................................................................................6-12

Spindle Disassembly ............................................................................................................................... 6-13

Spindle Assembly .................................................................................................................................... 6-13

Spindle Service..............................................................................................................................................6-14

Spindle Removal .....................................................................................................................................6-14

Spindle Installation ..................................................................................................................................6-14

Idler Arm / Deck Belt Tensioner Service ........................................................................................................6-15

Idler Arm / Tensioner Exploded View .............................................................................................................6-15

32 in. Stamped Deck ............................................................................................................................... 6-15

42 in. Stamped Deck ............................................................................................................................... 6-16

42 in. Fabricated Deck ............................................................................................................................6-17

50 in. Stamped Deck ............................................................................................................................... 6-18

50 in. Fabricated Deck ............................................................................................................................6-19

Idler Arm Inspection / Service ........................................................................................................................ 6-20

Idler Arm Removal ..................................................................................................................................6-20

Idler Arm Installation ...............................................................................................................................6-20

Checking for Bent Blades ..............................................................................................................................6-21

Leveling Mower Deck ....................................................................................................................................6-22

32 Inch Stamped Deck Leveling .................................................................................................................... 6-22

32 Inch Stamped Deck - Side-to-Side Leveling ......................................................................................6-22

32 Inch Stamped Deck - Adjusting the Front-to-Rear Blade Slope ......................................................... 6-25

42 & 50 Inch Stamped Deck Leveling ...........................................................................................................6-26

42 & 50 Inch Stamped Deck - Side-to-Side Leveling .............................................................................. 6-26

42 & 50 Inch Stamped Deck - Adjusting the Front-to-Rear Blade Slope ................................................6-29

42 Inch Fabricated Deck Leveling .................................................................................................................6-30

42 Inch Fabricated Deck - Side-to-Side Leveling ....................................................................................6-30

42 Inch Fabricated Deck - Adjusting the Front-to-Rear Blade Slope ......................................................6-32

50 Inch Fabricated Deck Leveling .................................................................................................................6-33

50 Inch Fabricated Deck Side-to-Side Leveling ...................................................................................... 6-33

50 Inch Fabricated Deck Adjusting the Front-to-Rear Blade Slope ........................................................6-34

TABLE OF CONTENTS

TOC-4 Toro TimeCutter SS/MX/ZS Service Manual

7 - Electrical

Chassis Switches ............................................................................................................................................7-1

Key/Ignition Switch ..........................................................................................................................................7-1

Purpose ..................................................................................................................................................... 7-1

Location ....................................................................................................................................................7-1

How It Works ............................................................................................................................................. 7-1

Testing .......................................................................................................................................................7-1

PTO Switch ...................................................................................................................................................... 7-2

Purpose ..................................................................................................................................................... 7-2

Location ....................................................................................................................................................7-2

How It Works ............................................................................................................................................. 7-2

Continuity Testing ...................................................................................................................................... 7-3

Seat Switch......................................................................................................................................................7-4

Purpose ..................................................................................................................................................... 7-4

Location ....................................................................................................................................................7-4

How It Works ............................................................................................................................................. 7-4

Testing .......................................................................................................................................................7-4

RH and LH Neutral Switch...............................................................................................................................7-5

Purpose ..................................................................................................................................................... 7-5

Location ....................................................................................................................................................7-5

How it Works .............................................................................................................................................7-5

Testing .......................................................................................................................................................7-5

Brake Actuator Module ....................................................................................................................................7-6

Purpose ..................................................................................................................................................... 7-6

Location ....................................................................................................................................................7-6

Brake Actuator Module Replacement ..............................................................................................................7-7

Brake Actuator Module Removal ..............................................................................................................7-7

Brake Actuator Module Installation ...........................................................................................................7-8

Testing and Diagnostic ....................................................................................................................................7-8

Brake Actuator Module Diagnostic Tips: ........................................................................................................ 7-10

Test: ........................................................................................................................................................7-10

Starter Solenoid & Starting System ............................................................................................................... 7-11

Purpose ...................................................................................................................................................7-11

Location ..................................................................................................................................................7-11

How It Works (solenoid only) ..................................................................................................................7-11

Starter Solenoid Testing (solenoid only)..................................................................................................7-11

Starter Solenoid Circuit & Operation .......................................................................................................7-12

Starting System Schematic ...........................................................................................................................7-13

Electric PTO Clutch .......................................................................................................................................7-14

Purpose .................................................................................................................................................. 7-14

Location ..................................................................................................................................................7-14

How It works ...........................................................................................................................................7-14

Testing .....................................................................................................................................................7-14

Coil Resistance Measurement ................................................................................................................7-14

PTO Clutch Continuity to Ground Check ................................................................................................7-15

Measuring Clutch Current Draw .............................................................................................................. 7-15

PTO Clutch Electrical Specications ....................................................................................................... 7-15

PTO Circuit & Operation .........................................................................................................................7-16

PTO Circuit Schematic ..................................................................................................................................7-17

PTO Clutch Replacement ..............................................................................................................................7-18

PTO Clutch Removal ..............................................................................................................................7-18

TABLE OF CONTENTS

TOC-5Toro TimeCutter SS/MX/ZS Service Manual

PTO Clutch Installation ...........................................................................................................................7-18

Hour Meter (If Equipped) ...............................................................................................................................7-19

Purpose ................................................................................................................................................... 7-19

Location ..................................................................................................................................................7-19

How It Works ........................................................................................................................................... 7-19

Testing .....................................................................................................................................................7-19

Fuse Block & Fuses.......................................................................................................................................7-20

Purpose ................................................................................................................................................... 7-20

Location ..................................................................................................................................................7-20

How It Works ........................................................................................................................................... 7-20

Testing .....................................................................................................................................................7-20

TimeCutter SS, MX & ZS Chassis Wire Harness 1 of 3 ................................................................................7-21

TimeCutter SS, MX & ZS Chassis Wire Harness 2 of 3 ................................................................................7-22

TimeCutter SS, MX & ZS Chassis Wire Harness 3 of 3 ................................................................................7-23

SAFETY INFORMATION

1-1

Toro TimeCutter SW/SWX Service Manual

1

This symbol means WARNING or PER -

SONAL SAFETY INSTRUCTION – read

the instruction because it has to do with

your safety. Failure to comply with the

instruction may result in personal injury

or even death.

This manual is intended as a service and repair manual

only. The safety instructions provided herein are for

troubleshooting, service, and repair of the TimeCutter®

SW, the TimeCutter® SWX zero radius turn mowers.

General Information

Think Safety First

Avoid unexpected starting of engine…

Always turn off the engine and disconnect the spark plug

wire(s) before cleaning, adjusting, or repair.

Avoid lacerations and amputations…

Stay clear of all moving parts whenever the engine is

running. Treat all normally moving parts as if they were

moving whenever the engine is running or has the

potential to start.

Avoid burns…

Do not touch the engine, mufer, or other components,

which may increase in temperature during operation,

while the unit is running or shortly after it has been

running.

Avoid res and explosions…

Avoid spilling fuel and never smoke while working with

any type of fuel or lubricant. Wipe up any spilled fuel

or oil immediately. Never remove the fuel cap or add

fuel when the engine is running. Always use approved,

labeled containers for storing or transporting fuel and

lubricants.

Avoid asphyxiation…

Never operate an engine in a conned area without

proper ventilation.

Avoid injury from batteries…

Battery acid is poisonous and can cause burns. Avoid

contact with skin, eyes and clothing. Battery gases can

explode. Keep cigarettes, sparks and ames away from

the battery.

Avoid injury due to inferior parts…

Use only original equipment parts to ensure that

important safety criteria are met.

Avoid injury to bystanders…

Always clear the area of bystanders before starting or

testing powered equipment.

Avoid injury due to projectiles…

Always clear the area of sticks, rocks or any other debris

that could be picked up and thrown by the powered

equipment.

Avoid modications…

Never alter or modify any part unless it is a factory

approved procedure.

Avoid unsafe operation…

Always test the safety interlock system after making

adjustments or repairs on the machine. Refer to the

Electrical section in this manual for more information.

The TimeCutter SW, and TimeCutter SWX

operator’s manuals contain safety information and

operating tips for safe operating practices. Operator’s

manuals are available online through your Toro parts

source or:

The Toro Company

Publications Department

8111 Lyndale Avenue South

Bloomington, MN 55420

!

SAFETY INFORMATION

1-2

Toro TimeCutter SW/SWX Service Manual

1

THIS PAGE INTENTIONALLY LEFT BLANK.

SPECIFICATIONS

2-1

Toro TimeCutter SW/SWX Service Manual

2

2015 TimeCutter Zero Turn Tractor Specications

Conguration SW3200 SW4200 SW5000

16 HP 452cc Toro 32” Mower, 1 Blade

22 HP 725 cc Kohler 42” Mower, 2 Blades

24.5 HP 708cc Toro 42” Mower, 2 Blades 42” Mower, 2 Blades

Power Systems

Clutch Electric Electric Electric

Transaxles Twin Hydro-Gear ZT-2100 Twin Hydro-Gear ZT-2100 Twin Hydro-Gear ZT-2200

Drive Belt Drive with self-

tensioning system

Belt Drive with self-

tensioning system

Belt Drive with self-

tensioning system

Max. Ground Speed

(Fwd)

(Rev)

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

Rear Tires 18 x 6.0-8 2-ply rated 18 x 7.5-8 2-ply rated 18 x 7.5-8 2-ply rated

Front Caster Tires 11 x 4.00-5 ribbed tread,

2-ply rated

13 x 5.00-6 ribbed tread,

2-ply rated

13 x 5.00-6 ribbed tread,

2-ply rated

Fuel Tank Capacity 3 gallons 3 gallons 3 gallons

Mowing Deck

Type Side Discharge Side Discharge Side Discharge

Deck Construction/

Material

13 gauge steel 13 gauge steel 12 gauge steel

Spindle Housing Die cast aluminum Die cast aluminum Die cast aluminum

Spindle Shaft/Bearings One 19.9mm diameter

spindle/permanently lubed

ball bearings

Two 17mm diameter

spindles/permanently

lubed ball bearings

Three 17mm diameter

spindles/permanently

lubed ball bearings

Blade Tip Speed 18,959 ft/min @ 3400

RPM

17,810 ft/min @ 3400

RPM

18,330 ft/min @ 3400

RPM

Cutting Height Positions 1.5” to 4.5” 7 positions 1.5” to 4.5” 7 positions 1.5” to 4.5” 7 positions

Anti-Scalp Rollers None 2 adjustable 2 adjustable

Frame Construction Riveted 10 gauge steel Riveted 10 gauge steel Riveted 10 gauge steel

Dimensions

Weight 554 lbs. 595 lbs. 659 lbs.

Width Outside Rear Tires 34.6” (87.9cm) 38.6” (99cm) 46.2” (117.3cm)

Width Outside Deck 39.2” (99.4cm) Deck

deector down

36.2” (91.9cm) Deck

deector up

53.8” (136.6cm) Deck

deector down

46.1” (117cm) Deck

deector up

63.1” (160.3cm) Deck

deector down

55” (139.7cm) Deck

deector up

Wheel Base 50.5” (128.3cm) 50.5” (128.3cm) 50.5” (128.3cm)

Overall Length 78.9” (200cm) 78.9” (200cm) 78.9” (200cm)

Height 45.4” (115.3cm) 45.4” (115.3cm) 45.4” (115.3cm)

SPECIFICATIONS

2-2

Toro TimeCutter SW/SWX Service Manual

2

2015 TimeCutter Zero Turn Tractor Specications cont.

Conguration SW5425 SW4250 SW5050

24 HP 725cc Kohler 50” Fab Deck, 3 Blades

24.5 HP 708cc Toro 54” Mower, 3 Blades 42” Fab Deck, 2 Blades 50” Fab Deck, 3 Blades

Power Systems

Clutch Electric Electric Electric

Transaxles Twin Hydro-Gear ZT-2200 Twin Hydro-Gear ZT-2200 Twin Hydro-Gear ZT-2800

Drive Belt Drive with self-

tensioning system

Belt Drive with self-

tensioning system

Belt Drive with self-

tensioning system

Max. Ground Speed

(Fwd)

(Rev)

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

High 7.0 MPH

Low 4.0 MPH

3.5 MPH

Rear Tires 18 x 7.5-8 2-ply rated 18 x 9.5-8 2-ply rated 18 x 9.5-8 2-ply rated

Front Castor Tires 13 x 5.00-6 ribbed tread,

2-ply rated

13 x 5.00-6 ribbed tread,

2-ply rated

13 x 5.00-6 ribbed tread,

2-ply rated

Fuel Capacity 3 gallons 3 gallons 3 gallons

Mowing Deck

Type Side Discharge Side Discharge Side Discharge

Deck Construction 12 gauge steel Fabricated 10 gauge steel Fabricated 10 gauge steel

Spindle Housing Die cast aluminum Die cast aluminum Die cast aluminum

Spindle Shaft/Bearings Three 17mm diameter

spindles permanently

lubed ball bearings

Two 17mm diameter

spindles permanently

lubed ball bearings

Three 17mm diameter

spindles permanently

lubed ball bearings

Tip Speed 18,320 ft/min @

3400 RPM

17,810 ft/min @

3400 RPM

18,330 ft/min @

3400 RPM

Cutting Height 1.5” to 4.5” 7 positions 1.5” to 4.5” 7 positions 1.5” to 4.5” 7 positions

Anti-Scalp Rollers 3 Adjustable 2 Adjustable 3 Adjustable

Frame Construction Riveted 10 gauge steel Riveted 10 gauge steel Riveted 10 gauge steel

Dimensions

Weight 688 lbs. 647 lbs. 713 lbs.

Width Outside Rear Tires 47.8” (121.4cm) 38.6” (98cm) 47.8” (121.4cm)

Width Outside Deck 67” (170.2cm) Deck

deector down

57.4” (145.8cm) Deck

deector up

54.0” (137.2cm) Deck

deector down

46.3” (117.6cm) Deck

deector up

61.6” (156.5cm) Deck

deector down

53.6” (136.1cm) Deck

deector up

Wheel Base 50.5” (128.3cm) 50.5” (128.3cm) 50.5” (128.3cm)

Overall Length 78.9” (200cm) 78.9” (200cm) 78.9” (200cm)

Height 45.9” (116.3cm) 45.4” (115.3cm) 45.9” (116.3cm)

SPECIFICATIONS

2-3

Toro TimeCutter SW/SWX Service Manual

2

Engine Specications

Model # Model Engine Information

74780 SW3200 Toro, Single Cylinder, 16 hp, High Idle: 3400 - 3450 RPM

74781 SW3200 Toro, Single Cylinder, 16 hp, High Idle: 3400 - 3450 RPM

74784 SW4200

Toro, Twin Cylinder, 24.5 hp, High Idle: 3300 + 100 RPM

74785 SW4200

Kohler, Twin Cylinder 22 hp, High Idle: 3300 + 100 RPM

74790 SW5000

Toro, Twin Cylinder, 24.5 hp, High Idle: 3300 + 100 RPM

74793 SW5425

Toro, Twin Cylinder, 24.5 hp, High Idle: 3300 + 100 RPM

74787 SWX5250

Toro, Twin Cylinder, 24.5 hp, High Idle: 3300 + 100 RPM

74797 SWX5050

Toro, Twin Cylinder, 24.5 hp, High Idle: 3300 + 100 RPM

74798 SWX5050

Koler, Twin cylinder, 24 hp, High Idle: 3300 + 100 RPM

SPECIFICATIONS

2-4

Toro TimeCutter SW/SWX Service Manual

2

Hydro-Gear ZT-2100, ZT-2200 Hydrostatic Transaxles

Fig. 001 PICT-1000

Lubrication 20w50 Engine Oil

Oil Capacity ZT-2100 54 . oz. / 1.687 qt. (1597ml) each

Oil Capacity ZT-2200 56 . oz. / 1.75 qt. (1650ml) each

Oil Level Check The transaxle is a sealed system and does not require periodic checking.

Check oil at the oil ll plug location only. Do not check the oil at the vent tube.

If the oil level needs to be checked, the transaxle must be removed.

The oil level must be when the transaxle is COLD.

Please see the illustration below for uid level specications.

Fluid Change Interval The transaxle is factory lled and does not require regular oil changes.

A. Top of ll port C. 0.75”-1.50” (19-38mm) depth

B. Oil level at 50°-100° F (10°-38° C)

D. Fill port

Checking the Hydraulic Oil Level

Fig. 002 PICT-1001a

A

D

C

B

SPECIFICATIONS

2-5

Toro TimeCutter SW/SWX Service Manual

2

Hydro-Gear ZT-2800 Hydrostatic Transaxles

Fig. 003 PICT-1002

Lubrication Toro HYPR-OIL 500 or 20w50 Engine Oil

Oil Capacity ZT-2800 77.23 . oz. (2284ml) each

Oil Level Check Check expansion reservoir and if necessary add the specied oil to the FULL COLD

line. See illustration below. Also see the Hydro-Gear ZT-2800 service manual

(BLN-52441).

Fluid Change Interval After the First 50 hours - change the oil and lters for the hydraulic system and bleed

the system.

Every 400 Hours - change the oil and lters for the hydraulic system and bleed the

system.

Checking the Hydraulic Oil Level

Fig. 004 PICT-1003

A

C

B

A. Expansion reservoir C. Engine

B. Full cold line

SPECIFICATIONS

2-6

Toro TimeCutter SW/SWX Service Manual

2

Torque Specications

Inch Series bolts and Screws

(A) Grade 1 & 2

(B) Grade 5

(C) Grade 8

Recommended fastener torque values are listed in the

following tables. For critical applications, as determined

by Toro, either the recommended torque or a torque

that is unique to the application is clearly identied and

specied in the service manual.

These torque specications for the installation and

tightening of fasteners shall apply to all fasteners

which do not have a specic requirement identied

in the service manual. The following factors shall be

consid ered when applying torque: cleanliness of the

fastener, use of a thread sealant (e.g. Loctite®), degree

of lubrication on the fastener, presence of a prevailing

torque feature, hardness of the surface underneath of

the fastener’s head, or similar condition which affects the

installation.

As noted in the following tables, torque values should

be reduced by 25% for lubricated fasteners to achieve

the similar stress as a dry fastener. Torque values may

also have to be reduced when the fastener is threaded

into aluminum or brass. The specic torque value should

be determined based on the aluminum or brass material

strength, fastener size, length of thread engagement,

etc.

The standard method of verifying torque shall be per-

formed by marking a line on the fastener (head or nut)

and mating part, then back off fastener 1/4 of a turn.

Measure the torque required to tighten the fastener until

the lines match up.

Fastener Identication

Metric Bolts and Screws

(A) Class 8.8 (B) Class 10.9

SPECIFICATIONS

2-7

Toro TimeCutter SW/SWX Service Manual

2

Standard Torque for Dry, Zinc Plated & Steel Fasteners (Inch Series)

Standard Torque for Dry, Zinc Plated, and Steel Fasteners (Inch Series)

Note: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite, or thread sealant such as Loctite.

Note: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

Note: The nominal torque values listed above for

Grade 5 and 8 fasteners are based on 75% of the

minimum proof load specified in SAE J429. The

tolerance is approximately ± 10% of the nominal torque

value. Thin height nuts include jam nuts.

Thread Size

Grade 1, 5, &

8 with Thin

Height Nuts

SAE Grade 1 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

SAE Grade 5 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

SAE Grade 8 Bolts, Screws,

Studs, & Sems with Regular

Height Nuts (SAE J995

Grade 2 or Stronger Nuts)

In-lb In-lb N-cm In-lb N-cm In-lb N-cm

# 6 - 32 UNC

10 ± 2 13 ± 2 147 ± 23

15 ± 2 169 ± 23 23 ± 2 260 ± 34

# 6 - 40 UNF 17 ± 2 190 ± 20 25 ± 2 280 ± 20

# 8 - 32 UNC

13 ± 2 25 ± 5 282 ± 30

29 ± 3 330 ± 30 41 ± 4 460 ± 45

# 8 - 36 UNF 31 ± 3 350 ± 30 43 ± 4 31 ± 3

# 10 - 24 UNC

18 ± 2 30 ± 5 339 ± 56

42 ± 4 475 ± 45 60 ± 6 674 ± 70

#10 - 32 UNF 48 ± 4 540 ± 45 68 ± 6 765 ± 70

1/4 - 20 UNC 48 ± 7 53 ± 7 599 ± 79 100 ± 10 1125 ± 100 140 ± 15 1580 ± 170

1/4 - 28 UNF 53 ± 7 65 ± 10 734 ± 113 115 ± 10 1300 ± 100 160 ± 15 1800 ± 170

5/16 - 18 UNC 115 ± 15 105 ± 15 1186 ± 169 200 ± 25 2250 ± 280 300 ± 30 3390 ± 340

5/16 - 24 UNF 138 ± 17 128 ± 17 1446 ± 192 225 ± 25 2540 ± 280 325 ± 30 3670 ± 340

ft-lb ft-lb N-m ft-lb N-m ft-lb N-m

3/8 - 16 UNC 16 ± 2 16 ± 2 22 ± 3 30 ± 3 41 ± 4 43 ± 4 58 ± 5

3/8 - 24 UNF 17 ± 2 18 ± 2 24 ± 3 35 ± 3 47 ± 4 50 ± 4 68 ± 5

7/16 - 14 UNC 27 ± 3 27 ± 3 37 ± 4 50 ± 5 68 ± 7 70 ± 7 68 ± 9

7/16 - 20 UNF 29 ± 3 29 ± 3 39 ± 4 55 ± 5 75 ± 7 77 ± 7 104 ± 9

1/2 - 13 UNC 30 ± 3 48 ± 7 65 ± 9 75 ± 8 102 ± 11 105 ± 10 142 ± 14

1/2 - 20 UNF 32 ± 3 53 ± 7 72 ± 9 85 ± 8 115 ± 11 120 ± 10 163 ± 14

5/8 - 11 UNC 65 ± 10 88 ± 12 119 ± 16 150 ± 15 203 ± 20 210 ± 20 285 ± 27

5/8 - 18 UNF 75 ± 10 95 ± 15 129 ± 20 170 ± 15 230 ± 20 240 ± 20 325 ± 27

3/4 - 10 UNC 93 ± 12 140 ± 20 190 ± 27 265 ± 25 359 ± 34 374 ± 35 508 ± 47

3/4 - 16 UNF 115 ± 15 165 ± 25 224 ± 34 300 ± 25 407 ± 34 420 ± 35 569 ± 47

7/8 - 9 UNC 140 ± 20 225 ± 25 305 ± 34 430 ± 45 583 ± 61 600 ± 60 813 ± 81

7/8 - 14 UNF 155 ± 25 260 ± 30 353 ± 41 475 ± 45 644 ± 61 660 ± 60 895 ± 81

SPECIFICATIONS

2-8

Toro TimeCutter SW/SWX Service Manual

2

Standard Torque for Dry, Zinc & Steel Fasteners (Metric Fasteners)

Standard Torque for Dry, Zinc, and Steel Fasteners (Metric Fasteners)

Note: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite, or thread sealant such as Loctite.

Note: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

Note: The nominal torque values listed above are

based on 75% of the minimum proof load specified in

SAE J1199. The tolerance is approximately ± 10% of

the nominal torque value. Thin height nuts include jam

nuts.

Thread Size

Class 8.8 Bolts, Screws, and Studs with

Regular Height Nuts

(Class 8 or Strong Nuts)

Class 10.9 Bolts, Screws, and Studs with

Regular Height Nuts (

Class 10 or Strong Nuts)

M5 X 0.8 57 ± 5 in-lb 644 ± 68 N-cm 78 ± 8 in-lb 881 ± 90 N-cm

M6 X 1.0 96 ± 10 in-lb 1085 ± 113 N-cm 133 ± 14 in-lb 1503 ± 158 N-cm

M8 X 1.25 19 ± 2 ft-lb 26 ± 3 N-m 28 ± 3 ft-lb 38 ± 4 N-m

M10 X 1.5 38 ± 4 ft-lb 52 ± 5 N-m 54 ± 6 ft-lb 73 ± 8 N-m

M12 X 1.75 66 ± 7 ft-lb 90 ± 10 N-m 93 ± 10 ft-lb 126 ± 14 N-m

M16 X 2.0 166 ± 15 ft-lb 225 ± 23 N-m 229 ± 23 ft-lb 310 ± 31 N-m

M20 X 2.5 325 ± 33 ft-lb 440 ± 45 N-m 450 ± 36 ft-lb 610 ± 62 N-m

SPECIFICATIONS

2-9

Toro TimeCutter SW/SWX Service Manual

2

Other Torque Specications

Other Torque Specifications

SAE Grade 8 Steel Set Screws

Thread Cutting Screws

(Zinc Plated Steel)

Conversion Factors

in-lb X 11.2985 = N-cm

ft-lb X 1.3558 = N-m

Wheel Bolts and Lug Nuts

** For steel wheels and non-lubricated fasteners.

Thread Cutting Screws

(Zinc Plated Steel)

* Hole size, material strength, material thickness and

finish must be considered when determining specific

torque values. All torque values are based on non-

lubricated fasteners.

N-cm X - 0.08851 = in-lb

N-cm X 0.73776 = ft-lb

Thread Size

Recommended Torque

Square Head Hex Socket

1/4 - 20 UNC 140 ± 20 in-lb 73 ± 12 in-lb

5/16 - 18 UNC 215 ± 35 in-lb 145 ± 20 in-lb

3/8 - 16 UNC 35 ± 10 ft-lb 18 ± 3 ft-lb

1/2 - 13 UNC 75 ± 15 ft-lb 50 ± 10 ft-lb

Type 1, Type 23, or Type F

Thread Size Baseline Torque*

No. 6 - 32 UNC 20 ± 5 in-lb

No. 8 - 32 UNC 30 ± 5 in-lb

No.10 - 24 UNC 38 ± 7 in-lb

1/4 - 20 UNC 85 ± 15 in-lb

5/16 - 18 UNC 110 ± 20 in-lb

3/8 - 16 UNC 200 ± 100 in-lb

Thread Size Recommended Torque**

7/16 - 20 UNF

Grade 5

65 ± 10 ft-lb 88 ± 14 N-m

1/2 - 20 UNF

Grade 5

80 ± 10 ft-lb 108 ± 14 N-m

M12 X 1.25

Class 8.8

80 ± 10 ft-lb 108 ± 14 N-m

M12 X 1.5

Class 8.8

80 ± 10 ft-lb 108 ± 14 N-m

Thread

Size

Threads per Inch

Baseline Torque*

Type A Type B

No. 6 18 20 20 ± 5 in-lb

No. 8 15 18 30 ± 5 in-lb

No. 10 12 16 38 ± 7 in-lb

No. 12 11 14 85 ± 15 in-lb

Page is loading ...

Toro TimeCutter SWX 4250 Riding Mower User manual

This manual is also suitable for

Toro TimeCutter SWX 4250 Riding Mower User manual

Related papers

Other documents