Vivo STAND-V001O Assembly Instructions

Brand: Vivo

Model: STAND-V001O

Category: Flat panel desk mounts

Type: Assembly Instructions

This manual is also suitable for

Vivo STAND-V001O is a pneumatic single monitor desk mount with USB ports, designed to enhance your workspace with its ergonomic features and versatility. It supports monitors weighing between 4.4 and 19.8 lbs, making it suitable for a wide range of displays. The gas spring arm allows for smooth and effortless adjustment of your monitor's height, tilt, and swivel, promoting a comfortable viewing angle that reduces neck and eye strain.

Pneumatic Arm Single Monitor Desk Mount with USB

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v001ou

SKU: STAND-V001OU

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

4.4-19.8lbs

(2-9kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PACKAGE CONTENTS

A (x1)

Gas Spring

Arm

B (x1)

Bracket

C (x1)

Clamp

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

D (x3)

M6x12

E (x2)

M6x10

F (x1)

Grommet

Base

G (x1)

Carriage Bolt

H (x1)

Support Plate

M-A (x4)

M4x12

M-B (x4)

M5x12

I (x1)

Wing Nut

J (x1)

4mm Allen Wrench

M-C (x4)

D5 Washer

K (x1)

5mm Allen Wrench

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

ASSEMBLY STEPS

STEP 2

STEP 1

Remove gas spring arm (A) from packaging. While holding arm closed, cut the

shipping tie and gently release arm.

OPTION A: Clamp Installation

Mount bracket (B) to bottom of gas spring arm (A) using M6x12 bolts (D). Tighten using 4mm

Allen wrench (J). Attach clamp (C) to bracket (B) using M6x10 bolts (E) and 4mm Allen wrench

(J). Install according to thickness of desktop as shown in diagrams. Secure stand to desktop by

tightening clamp (C).

OPTION A: Clamp Installation

Mount bracket (B) to bottom of gas spring arm (A) using M6x12 bolts (D). Tighten using 4mm

Allen wrench (J). Attach clamp (C) to bracket (B) using M6x10 bolts (E) and 4mm Allen wrench

(J). Install according to thickness of desktop as shown in diagrams. Secure stand to desktop by

tightening clamp (C).

STEP 2 (Continued)

STEP 3

Attach two bolts (M-A or M-B) and washers

(M-C) to top mounting holes of monitors,

making sure to leave 3mm of threads

exposed. Align bolts (M-A, M-B) in VESA

plates. Secure using two more bolts (M-A or

M-B) and washers (M-C) in the bottom two

holes. Tighten all four bolts using Phillips

screwdriver end of 5mm Allen wrench (K).

OPTION B: Grommet Base Installation

For grommet hole mounting, place carriage bolt (G) through the

center of grommet base (F). Mount grommet base to bottom of

gas spring arm (A) using M6x12 bolts (D). Tighten using 4mm

Allen wrench (J). Run carriage bolt (G) through grommet hole

in desktop. If no grommet hole is present, drill hole using a

3/8” (10mm) drill bit. Attach support plate (H) and wing nut (I).

Tighten wing nut to secure.

STEP 4

Adjust tension in gas spring arm (A) using 5mm Allen wrench (K). Turning clockwise decreases

strength, and counter-clockwise increases.

STEP 5

Remove bottom plastic covers from gas spring arm (A) using Phillips screwdriver end of 5mm Allen

wrench (K). Run cables from monitor through bottom of gas spring arm (A), then reattach plastic

covers.

STEP 6

Adjust monitor tilt support using 5mm Allen wrench (K) as shown.

Adjust monitor position as desired.

Connect USB and audio cables to

ports on computer.

LAST UPDATED: 08/06/2020

REV2

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-V001O Assembly Instructions

Brand: Vivo

Model: STAND-V001O

Category: Flat panel desk mounts

Type: Assembly Instructions

This manual is also suitable for

Download PDF

report

Vivo STAND-V001O Assembly Instructions

This manual is also suitable for

Vivo STAND-V001O Assembly Instructions

Related papers

Other documents