CURT 45920 User manual

Type
User manual

CURT 45920 is a channel-mount forged pintle and ball mount, designed for towing heavy loads. It has a gross trailer weight capacity of 13,000 lbs and a tongue weight capacity of 1,300 lbs. The 2 5/16-inch ball can be used for towing trailers with a ball coupler, while the pintle hook can be used for towing trailers with a lunette ring. The adjustable channel-mount shank allows for easy height adjustment, and the anti-rattle set screw helps to eliminate noise. Safety features include a latch lock and safety pin for the pintle hook, and a clip for the ball.

CURT 45920 is a channel-mount forged pintle and ball mount, designed for towing heavy loads. It has a gross trailer weight capacity of 13,000 lbs and a tongue weight capacity of 1,300 lbs. The 2 5/16-inch ball can be used for towing trailers with a ball coupler, while the pintle hook can be used for towing trailers with a lunette ring. The adjustable channel-mount shank allows for easy height adjustment, and the anti-rattle set screw helps to eliminate noise. Safety features include a latch lock and safety pin for the pintle hook, and a clip for the ball.

CHANNEL-MOUNT FORGED PINTLE & BALL
Figure 1
Do not exceed vehicle's towing capacity or trailer hitch
capacity, whichever is less. See your vehicle owner's
manual to determine vehicle tow rating.
This pintle hitch can only be used with the channel-mount
system. Use of any channel-mount other than that of the
channel-mount system manufacturer could be a serious
safety hazard and will void the warranty.
Ensure that the safety chains operate freely around the
channel-mount system and do not become entangled in the
channel-mount system.
Before towing, ensure the pintle ball is torqued to 260 ft. lbs.
DISCLAIMER: The ratings of the channel-mount system are
intended to represent the capability of the product and in
no way reflect the ratings or capacity of the towing system
it is being used with. The consumer or operator are strongly
advised to learn the ratings of the various components of
the towing system and never exceed the limits of the lowest
rated component being used.
Install the adjustable channel-mount shank into the trailer
hitch of the vehicle and secure with a hitch pin & clip.
Always secure the hitch pin with a clip unless a locking
device is being used.
Raise or lower the pintle to the desired height and insert the
channel-mount system pins through the holes that line up
with the holes in the channel-mount. Secure the pins with
clips. There are pins & clips specifically engineered NOTE:
for the channel-mount system. If replacement pins are
needed, they must be replaced with original factory channel-
mount pins.
After the pintle is set to the correct height and secured,
tighten the anti-rattle set screw tightly into the channel-mount
to eliminate noise. See figure 1. Use of a set screw NOTE:
is not needed for safety; only to eliminate possible rattle
between the channel-mount shank and the pintle.
If towing with the trailer ball, open the pintle latch by
removing the safety pin and pulling up on the lock while
lifting the latch. Replace the safety pin to retain the open
latch position. Position the coupler over the trailer ball and
lock it into place following the instructions of the coupler
manufacturer.
Prior to towing check to make sure the pins are secured into
place with clips. Never hook up trailer safety chains to the
channel-mount system.
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
INSTALLATION INSTRUCTIONS
WARNINGS
PARTS LISTUSE
Part# Ball Size Gross Trailer Weight / Tongue Weight
45919 2" 10,000 / 1,000 lbs.
45920 2 5/16" 13,000 / 1,300 lbs.
45922 2 5/16" 20,000 / 2,000 lbs.
PAGE 1 • RA • 1.877.287.8634 • NEED ASSISTANCE? CURTMFG.COM
  • Page 1 1

CURT 45920 User manual

Type
User manual

CURT 45920 is a channel-mount forged pintle and ball mount, designed for towing heavy loads. It has a gross trailer weight capacity of 13,000 lbs and a tongue weight capacity of 1,300 lbs. The 2 5/16-inch ball can be used for towing trailers with a ball coupler, while the pintle hook can be used for towing trailers with a lunette ring. The adjustable channel-mount shank allows for easy height adjustment, and the anti-rattle set screw helps to eliminate noise. Safety features include a latch lock and safety pin for the pintle hook, and a clip for the ball.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI