Denver RLT-1201 User manual

Type
User manual

This manual is also suitable for

ENG 1
RLT-1001
Denver.eu
ENG 2
Safety information
Please read the safety instructions carefully before using
the product for the first time
and keep the instructions for future reference.
1. The product is not a toy. Keep product out of
the reach of children and pets to avoid
chewing and swallowing.
2. Product operating and storage temperature is
from 0 degrees Celsius to 40 degrees Celsius.
Environments under and above this
temperature might affect functionality.
3. Never open the product. Do not touch the
inside electronics, or you may get an electric
shock. Repair or service are only to be
performed by qualified personnel.
4. Do not expose to heat, water, moisture, direct
sunlight!
5. The unit is not waterproof. If water or foreign
objects enter the unit, it may result in fire or
ENG 3
electric shock. If water or a foreign object
enters the unit, stop using it immediately.
6. Do not look directly into the LED light as this
can damage your eyes.
1. Product Specifications
10-Inch Ring Light
Color: Black
Power Supply: USB Interface
Material: ABS + PC
Number of LEDs: 120
Ring Size: Diameter 10 Inch/26 cm
Color Temperature: 3000 - 6500K
Special Note:
1. The ring light is not rechargeable. You need to
connect to a power supply via USB cable before
using it.
ENG 4
2. Please do not place this product in a bathroom or
other humid environment to avoid short-circuit.
3. Please do not place this product in an
environment where flammable liquid is likely to
come into contact with this product.
2. In the Box
1 x LED Ring Light with USB Cable
1 x Stretchable Universal Phone Clip (Optional)
1 x 360° Ball Joint
1 x Installation Manual
3. Installation
ENG 5
Step 1
Step 2
Step 1: The ball joint is connected to the LED ring light by
¼” thread.
Step 2: Connect the phone clip to the ring light through
¼” standard thread.
3.1 USB Power Supply
USB power supply works with various USB ports on
Laptop, PC, power bank, USB charger, etc.
ENG 6
3.2 & 3.3 Light Modes & Brightness
1. The LED ring light has 3 light modes (Cool, Soft,
Warm), and can be adjusted to 10 different brightness
levels.
2. Connect the USB cable to a USB power source (not
included) and press the ON/OFF button to turn it on.
Press again to turn it off. The brightness level is adjusted
by pressing the “+” and “-“ buttons.
Brightness-
Mode setting (3 Lighting Modes)
ON/OFF
10 levels of adjustable brightness
Brightness+
ENG 7
Please notice - All products are subject to change
without any notice. We take reservations for errors and
omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER A/S
Electric and electronic equipment contains materials,
components and substances that can be hazardous to
ENG 8
your health and the environment, if the waste material
(discarded electric and electronic equipment) is not
handled correctly.
Electric and electronic equipment is marked with the
crossed out trash can symbol, seen above. This symbol
signifies that electric and electronic equipment should
not be disposed of with other household waste, but
should be disposed of separately.
All cities have established collection points, where
electric and electronic equipment can either be
submitted free of charge at recycling stations and other
collection sites, or be collected from the households.
Additional information is available at the technical
department of your city.
DENVER A/S
Omega 5A, Soeften
DK-8382 Hinnerup
Denmark
www.facebook.com/denver.eu
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Denver RLT-1201 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI