Gainsborough Trilock Urban Installation guide

Gainsborough
Brand
Gainsborough
Model
Trilock Urban
Type
Installation guide

Gainsborough Trilock Urban is a double cylinder deadbolt designed for residential use. It features a 22mm latch and a 60mm backset, making it suitable for doors between 35mm and 45mm thick. The Trilock Urban is easy to install and comes with a template for precise drilling. It also includes a bolt re-handing feature, allowing you to change the handing of the door without removing the lock. With its durable construction and stylish design, the Gainsborough Trilock Urban is a reliable and attractive security solution for your home.

Gainsborough Trilock Urban is a double cylinder deadbolt designed for residential use. It features a 22mm latch and a 60mm backset, making it suitable for doors between 35mm and 45mm thick. The Trilock Urban is easy to install and comes with a template for precise drilling. It also includes a bolt re-handing feature, allowing you to change the handing of the door without removing the lock. With its durable construction and stylish design, the Gainsborough Trilock Urban is a reliable and attractive security solution for your home.

Step 1.
• Fold template where indicated.
• Position template on door edge at
desired lock / latch height.
• Firmly hold template and mark latch
height and 2 60mm holes centres.
• Measure door thickness and mark
centre on 'latch height' marking.
• Drill 22mm (7/8") latch hole.
Note: it is important to drill this
hole squarely.
Step 2.
• Mark vertical lines between
two holes as per illustration.
• Cut along marked lines.
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
NOTES: • Carefully follow these instructions when installing.
•Do not overtighten screws.
•Use of power driver is not recommended for screw installation.
•Fully remove the Trilock prior to painting the door to avoid
damaging the product's finish
• Suitable door thickness is between 35 and 45mm
Patent Pending
Installation Instructions Trilock Urban
- Double Cylinder
Suits 35mm to 45mm Door Thickness
TEV1DOC02UM1
Oct ‘17 Issue 2
Step 1.
• Fold template where indicated.
• Position template on door edge at
desired lock / latch height.
• Firmly hold template and mark latch
height and 2 60mm holes centres.
• Measure door thickness and mark
centre on 'latch height' marking.
• Drill 22mm (7/8") latch hole.
Note: it is important to drill this
hole squarely.
• Drill pilot holes [suggested size
3mm (1/8")]. Then enlarge holes
to 60mm, drilling from both sides
of the door.
In particular, ensure the 60mm dia.
holes through door face are drilled
only to this size, otherwise correct
functioning may be impeded –
refer template.
Step 4a.
Trilock latch bolt re-handing.
• Check that tapered side of the
latch bolt faces towards the door jamb.
• It may be necessary to unclip
the rear arm & rotate bolt 180.
• This is achieved by following steps:
Step 2.
• Mark vertical lines between
two holes as per illustration.
• Cut along marked lines.
Please note: Ensure the template
position and orientation is as shown,
incorrect installation voids warranty.
Mark vertical lines between holes
as shown. Cut along vertical lines.
NOTE: • carefully follow these instructions when installing.
• do not overtighten screws.
• use of power driver is notrecommended.
• fully remove the Trilock prior to painting the door
to avoid harming the product's finish.
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
1. Remove latch bolt assembly from carrier
4. Rotate bolt 180˚ 5. Re-attach arm to latch bolt
6. Rotate arm upwards &
fit back into carrier
2. Rotate arm downwards
3. Unclip arm from latch bolt
Arm
Rotate Bolt 180˚
Step 3.
• Mark and chisel latch faceplate to a recess of 2mm.
Use latch carrier as a template.
• Insert lock body into 60mm (2 3/8") slot.
• Insert latch carrier through 22mm
(7/8") hole into lock body assembly
and tighten with 2 screws.
Ensure T-shaped hole at rear
of latch carrier is upright!
T-Shaped hole
Rear view
of latch
Latch
carrier
Lock
body Screws
Step 4.
• Insert the latch through the slot in the carrier until it can go no further.
• Insert the key and turn to retract the latch bolt.
• Pre-drill wood screw holes with suitable drill size.
• Install faceplate, then screw into position.
B
a
b
c
d
Step 1.
Prepare the door.
a. Fold template where indicated.
b. Position template on door edge
at desired lock / latch height.
c.
latch height, and hole centres
on both sides of the door
(Reverse the template fold for
the opposite side).
d. Measure door thickness and
mark centre on 'latch height'
marking.
e. Drill pilot holes using the
Ø3mm drill.
f. Drill Ø10mm holes and Ø54mm
hole from both sides of the door.
g. Drill Ø22mm latch hole.
Note: it is important to drill this
hole squarely.
Step 2.
Disassemble the
Lockbody.
a. Ensure the bolt is in
the fully extended
position by rotating
the key towards the
latch carrier.
b. Remove the 2 screws
from the lockbody and
pull the latch carrier
out of the lockbody.
Step 4
Bolt Handing
a. Check the tapered side of the latchbolt faces towards the door jamb,
(when the arm is orientated as shown).
b. Refer to next step for bolt rehanding procedure if required.
Step 3
Install Lockbody
a. Mark and chisel latch faceplate to a
recess of 3.5mm.
Use latch carrier as a template.
b. Insert lock body into 54mm hole.
c. Insert latch carrier through 22mm
hole and into lockbody.
d. Install 2 lockbody screws to secure.
a
b
b
b
The T-Shape hole
is always up.
Ensure the
T-Shaped
hole at the
rear of the
latch carrier
is upright!
Left handed
Arm
Right handed Arm
Door
Door
Jamb
Door
Door
Jamb
Ø10
Lockbody
Bolt
Latch
Carrier
Ø54
Ø22
rilock Eclipse
Suits 35mm to 45mm door thickness
NOTES: • Carefully follow these instructions when installing.
•Do not overtighten screws.
•Use of power driver is not recommended for screw installation.
•Fully remove the Trilock prior to painting the door to avoid
damaging the product's finish
• Suitable door thickness is between 35 and 45mm
Patent Pending
Installation Instructions Trilock Urban
- Double Cylinder
Suits 35mm to 45mm Door Thickness
TEV1DOC02UM1
Oct ‘17 Issue 2
Step 1.
• Fold template where indicated.
• Position template on door edge at
desired lock / latch height.
• Firmly hold template and mark latch
height and 2 60mm holes centres.
• Measure door thickness and mark
centre on 'latch height' marking.
• Drill 22mm (7/8") latch hole.
Note: it is important to drill this
hole squarely.
• Drill pilot holes [suggested size
3mm (1/8")]. Then enlarge holes
to 60mm, drilling from both sides
of the door.
In particular, ensure the 60mm dia.
holes through door face are drilled
only to this size, otherwise correct
functioning may be impeded –
refer template.
Step 4a.
Trilock latch bolt re-handing.
• Check that tapered side of the
latch bolt faces towards the door jamb.
• It may be necessary to unclip
the rear arm & rotate bolt 180.
• This is achieved by following steps:
Step 2.
• Mark vertical lines between
two holes as per illustration.
• Cut along marked lines.
Please note: Ensure the template
position and orientation is as shown,
incorrect installation voids warranty.
Mark vertical lines between holes
as shown. Cut along vertical lines.
NOTE: • carefully follow these instructions when installing.
• do not overtighten screws.
• use of power driver is notrecommended.
• fully remove the Trilock prior to painting the door
to avoid harming the product's finish.
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
1. Remove latch bolt assembly from carrier
4. Rotate bolt 180˚ 5. Re-attach arm to latch bolt
6. Rotate arm upwards &
fit back into carrier
2. Rotate arm downwards
3. Unclip arm from latch bolt
Arm
Rotate Bolt 180˚
Step 3.
• Mark and chisel latch faceplate to a recess of 2mm.
Use latch carrier as a template.
• Insert lock body into 60mm (2 3/8") slot.
• Insert latch carrier through 22mm
(7/8") hole into lock body assembly
and tighten with 2 screws.
Ensure T-shaped hole at rear
of latch carrier is upright!
T-Shaped hole
Rear view
of latch
Latch
carrier
Lock
body Screws
Step 4.
• Insert the latch through the slot in the carrier until it can go no further.
• Insert the key and turn to retract the latch bolt.
• Pre-drill wood screw holes with suitable drill size.
• Install faceplate, then screw into position.
B
c
d
a
b
Step 4 (continued)
Re-hand bolt if needed; (Right Hand to Left Hand shown)
Arm
Pin
Spring
Bolt
Hook end of arm is
orientated as shown.
Step 5
Install the bolt
a. Insert the bolt assembly into the latch carrier
until it stops and a click is heard.
NOTE: the hook end of the arm must be
orientated as shown.
b. Rotate the key away from the edge of the
door and the bolt should retract.
If the bolt does not retract, rotate the key
towards the edge of the door and repeat
steps a. and b. above.
c. Predrill the faceplate screws holes.
d. Install the faceplate and faceplate screws.
a
b
Step 6a
Rehand the Interior
Lever (If necessary)
a.
into the handing hole
adjacent to the lever.
b. While pushing the
screwdriver in, rotate the
lever upwards and to the
other side until a click is
heard.
Step 6b
Rehand the Exterior
Lever
(If necessary)
a. Push the handing plate
adjacent to the lever as shown.
or screwdriver).
b. Rotate the lever upwards and
over to the other side until a
click is heard.
a
b
a. Rotate arm downwards. b. Unclip from the bolt. c. Rotate the bolt 180 degrees. d. Re-attach the arm
to the bolt and
rotate arm upwards.
Right handed bolt Left handed bolt
Note: Ensure the spring and pin remain in the bolt.
Use the handing hole
closest to the lever
external
3mm (1/8")]. Then enlarge holes
to 60mm, drilling from both sides
of the door.
In particular, ensure the 60mm dia.
holes through door face are drilled
only to this size, otherwise correct
functioning may be impeded –
refer template.
Step 4a.
Trilock latch bolt re-handing.
• Check that tapered side of the
latch bolt faces towards the door jamb.
• It may be necessary to unclip
the rear arm & rotate bolt 180.
• This is achieved by following steps:
Please note: Ensure the template
position and orientation is as shown,
incorrect installation voids warranty.
Mark vertical lines between holes
as shown. Cut along vertical lines.
NOTE: • carefully follow these instructions when installing.
• do not overtighten screws.
• use of power driver is notrecommended.
• fully remove the Trilock prior to painting the door
to avoid harming the product's finish.
Patent Pending
1. Remove latch bolt assembly from carrier
4. Rotate bolt 180˚ 5. Re-attach arm to latch bolt
2. Rotate arm downwards
Arm
Rotate Bolt 180˚
PAIT 149
NOV ‘15
Step 3.
• Mark and chisel latch faceplate to a recess of 2mm.
Use latch carrier as a template.
• Insert lock body into 60mm (2 3/8") slot.
• Insert latch carrier through 22mm
(7/8") hole into lock body assembly
and tighten with 2 screws.
Ensure T-shaped hole at rear
of latch carrier is upright!
T-Shaped hole
Rear view
of latch
Latch
carrier
Lock
body Screws
Step 4.
• Insert the latch through the slot in the carrier until it can go no fu
• Insert the key and turn to retract the latch bolt.
• Pre-drill wood screw holes with suitable drill size.
• Install faceplate, then screw into position.
NOTES: • Carefully follow these instructions when installing.
•Do not overtighten screws.
•Use of power driver is not recommended for screw installation.
•Fully remove the Trilock prior to painting the door to avoid
damaging the product's finish
• Suitable door thickness is between 35 and 45mm
Patent Pending
Installation Instructions Trilock Urban
- Double Cylinder
Suits 35mm to 45mm Door Thickness
TEV1DOC02UM1
Oct ‘17 Issue 2
Step 1.
• Fold template where indicated.
• Position template on door edge at
desired lock / latch height.
• Firmly hold template and mark latch
height and 2 60mm holes centres.
• Measure door thickness and mark
centre on 'latch height' marking.
• Drill 22mm (7/8") latch hole.
Note: it is important to drill this
hole squarely.
• Drill pilot holes [suggested size
3mm (1/8")]. Then enlarge holes
to 60mm, drilling from both sides
of the door.
In particular, ensure the 60mm dia.
holes through door face are drilled
only to this size, otherwise correct
functioning may be impeded –
refer template.
Step 4a.
Trilock latch bolt re-handing.
• Check that tapered side of the
latch bolt faces towards the door jamb.
• It may be necessary to unclip
the rear arm & rotate bolt 180.
• This is achieved by following steps:
Step 2.
• Mark vertical lines between
two holes as per illustration.
• Cut along marked lines.
Please note: Ensure the template
position and orientation is as shown,
incorrect installation voids warranty.
Mark vertical lines between holes
as shown. Cut along vertical lines.
NOTE: • carefully follow these instructions when installing.
• do not overtighten screws.
• use of power driver is notrecommended.
• fully remove the Trilock prior to painting the door
to avoid harming the product's finish.
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
1. Remove latch bolt assembly from carrier
4. Rotate bolt 180˚ 5. Re-attach arm to latch bolt
6. Rotate arm upwards &
fit back into carrier
2. Rotate arm downwards
3. Unclip arm from latch bolt
Arm
Rotate Bolt 180˚
Step 3.
• Mark and chisel latch faceplate to a recess of 2mm.
Use latch carrier as a template.
• Insert lock body into 60mm (2 3/8") slot.
• Insert latch carrier through 22mm
(7/8") hole into lock body assembly
and tighten with 2 screws.
Ensure T-shaped hole at rear
of latch carrier is upright!
T-Shaped hole
Rear view
of latch
Latch
carrier
Lock
body Screws
Step 4.
• Insert the latch through the slot in the carrier until it can go no further.
• Insert the key and turn to retract the latch bolt.
• Pre-drill wood screw holes with suitable drill size.
• Install faceplate, then screw into position.
B
a
b
d
Step 7
Post installation
a.
Install posts to external
furniture plate, ensuring
against the plate.
(This is the furniture plate
without the rectangular
snib push-button.)
Step 8.
Assemble the furniture to the door.
a.
Mount external furniture plate to the
outside of door.
b.
Now mount the internal furniture plate
to the inside of door.
c.
Ensure the furniture is straight
on both sides of the door.
d.
Fit mounting screws from
inside & tighten into threaded
posts.
e.
Test all lock functions
for smooth operation.
Step 9
Fit the strike plate.
a. Position the door so that the centrepoint of
the bolt can be marked on door frame.
b. Mark and drill a 25mm hole to a depth of 25mm,
at a corresponding height to the bolt.
c. Mark and chisel recesses for the strike plate.
d. Screw the strike plate into position using the 2
wood screws supplied.
Door Adjustment
ensure bolt is latching into strike plate.
e. If door is rattling when in latched position. Open door,
plate to door frame. Check if the door is rattling and
adjust again if necessary.
a
e
b,c
d
Posts
Mounting
screws
External
furniture
plate
Outside
Inside
Patent PendingPAIT 149
NOV ‘15
Patent Pending
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
Designed in Australia by Gainsborough Hardware Industries Limited, Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
Exploded Diagram
faceplat e
latch
snib rotor
spring
plastic
insert
latch
carrier
insid e
fur nitu re
outside
furniture
cylinder
lock body
pos t
strike plate
ORIGINATION CRM GSH 954 1115
PAIT 149
NOV ‘15
Patent Pending
Installation Instructions for Trilock Eclipse
Suits 35mm to 45mm door thickness
Designed in Australia by Gainsborough Hardware Industries Limited, Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
Exploded Diagram
faceplat e
latch
snib rotor
spring
plastic
insert
latch
carrier
insid e
fur nitu re
outside
furniture
cylinder
lock body
pos t
strike plate
ORIGINATION CRM GSH 954 1115
PAIT 149
NOV ‘15
Patent Pending
TEV1DOC02UM1
Oct ‘17 Issue 2
Posts
Bolt
Lockbody
Mounting Screws
Interior Furniture Plate
Face Plate
Strike Plate
Latch Carrier
Exterior Furniture Plate
Installation Instructions Trilock Urban
- Double Cylinder
Suits 35mm to 45mm Door Thickness
tical lines between holes
ical lines.
5. Re-attach arm to latch bolt
6. Rotate arm upwards &
fit back into carrier
3. Unclip arm from latch bolt
ough the slot in the carrier until it can go no further.
tract the latch bolt.
ew holes with suitable drill size.
ew into position.
B
Exploded Diagram
Double Cylinder version
Patent PendingPAIT 149
NOV ‘15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Gainsborough Trilock Urban Installation guide

Gainsborough
Brand
Gainsborough
Model
Trilock Urban
Type
Installation guide

Gainsborough Trilock Urban is a double cylinder deadbolt designed for residential use. It features a 22mm latch and a 60mm backset, making it suitable for doors between 35mm and 45mm thick. The Trilock Urban is easy to install and comes with a template for precise drilling. It also includes a bolt re-handing feature, allowing you to change the handing of the door without removing the lock. With its durable construction and stylish design, the Gainsborough Trilock Urban is a reliable and attractive security solution for your home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents