Black Box AVSW-HDMI-RX User manual

Brand: Black Box

Model: AVSW-HDMI-RX

Category: Video switches

Type: User manual

This manual is also suitable for

BL A C K B OX

Use this high-performance matrix to switch and

extend multiple video and audio signals.

Switch manually, from a remote control unit, RS-232 interface, or Ethernet.

Includes built-in HDBaseT

interfaces for 328-ft. (100 m) extension.

XR 8 x 8 HDMI Matrix Switch with Audio

AVSW-HDMI8X8-X

AVSW-HDMI-RX

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: info@blackbox.com

Customer

Support

Information

724-746-5500 | blackbox.com

Page 2

724-746-5500 | blackbox.com

Trademarks Used in this Manual/ FCC and IC RFI Statements

We‘re here to help! If you have any questions about your application

or our products, contact Black Box Tech Support at 724-746-5500

or go to blackbox.com and click on “Talk to Black Box.”

You’ll be live with one of our technical experts in less than 30 seconds.

Trademarks Used in this Manual

Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc.

Blu-ray is a trademark of the Blu-ray Disc Association.

HDMI is a registered trademark of HDMI Licensing L.L.C.

Xbox and Windows are registered trademarks of Microsoft Corporation.

Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.

Federal Communications Commission and Industry Canada Radio Frequency Interference

Statements

This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict

accordance with the manufacturer’s instructions, may cause inter ference to radio communication. It has been tested and found to

comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules,

which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set out in the Radio

Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques

de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.

724-746-5500 | blackbox.com

Page 3

NOM Statement

Instrucciones de Seguridad

(Normas Oficiales Mexicanas Electrical Safety Statement)

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca

de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.

Todo otro servicio deberá ser referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico

sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes

que impidan el flujo de aire por los orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros

aparatos (incluyendo amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como

se indique en el aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados

sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

724-746-5500 | blackbox.com

Page 4

724-746-5500 | blackbox.com

Safety Information

NOTE: THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS

MANUAL.

1. Save the carton and packing material even if the equipment has arrived in good condition. If you ever need to ship the unit, use only the

original factory packing.

2. Read all documentation before operating your equipment. Retain all documentation for future reference.

3. Follow all instructions printed on unit chassis for proper operation.

4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

5. Make sure power outlets conform to the power requirements listed on the back of the unit.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be

walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and

the point where they exit.

7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means

of grounding of a piece of equipment is not defeated.

8. Voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not

covered by any warranty.

9. Power down and disconnect the unit from mains voltage before making connections.

10. Never hold a power switch in the “ON” position.

11. Do not use the unit near stoves, heat registers, radiators, or other heat-producing devices.

12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow

of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign matter.

13. Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.

14. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

15. Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.

16. Service information equipment should be serviced by qualifier service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain.

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

724-746-5500 | blackbox.com

Page 5

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

To get the best from this product, please read this manual carefully. Keep it in a safe place for future reference.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS ARE

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Do not force switched or external connections.

When moving the unit, disconnect the serial port connections first, then the power cable, and finally the interconnecting cables to other devic-

es.

Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.

Installation of this unit should be in a cool, dry place, away from sources of excessive heat, vibration, dust, moisture, and cold.

WARNING: To prevent electric shock do not use the (polarized) plug with an extension cord, receptacle, or other outlet unless the

blades can be fully inserted to prevent blade exposure. To prevent electric shock, match wide blade of plug to wide

slot; fully insert.

724-746-5500 | blackbox.com

Page 6

724-746-5500 | blackbox.com

Table of Contents

1. Specifications .........................................................................................................................................................................7

2. Overview ...............................................................................................................................................................................9

2.1 Introduction ...................................................................................................................................................................9

2.2 Features .........................................................................................................................................................................9

2.3 What’s Included ..........................................................................................................................................................10

2.4 Hardware Description ..................................................................................................................................................10

2.4.1 Front Panel of the AVSW-HDMI8X8-X .............................................................................................................. 10

2.4.2 Rear Panel of the AVSW-HDMI8X8-X ............................................................................................................... 13

2.4.3 Front and Rear Panels of the AVSW-HDMI-RX ................................................................................................. 15

3. Installation ...........................................................................................................................................................................16

3.1 Installation Diagram .................................................................................................................................................... 16

3.2 IR Extender .................................................................................................................................................................. 17

4. Operation ............................................................................................................................................................................18

4.1 EDID Setup .................................................................................................................................................................. 18

4.2 RESET .......................................................................................................................................................................... 18

4.3 Embedded EDID Modes .............................................................................................................................................. 19

4.4 LEARNING EDID .......................................................................................................................................................... 19

4.5 EDID Function for HDMI Matrix Switch .......................................................................................................................20

4.6 EDID Function: LEARNING ........................................................................................................................................... 21

4.7 EDID Status .................................................................................................................................................................. 21

4.8 How to Set Up Fast Speed Start (FSS) Function ...........................................................................................................22

4.9 Auto Mode Definition .................................................................................................................................................22

4.10 Consumer Electronics Control (CEC) Setup ..................................................................................................................22

4.11 Front-Panel Control Functions .....................................................................................................................................22

4.12 Remote Control ...........................................................................................................................................................23

4.13 IR Remote Custom and Data Codes (NEC Standard) ...................................................................................................24

5. Room Remote Control #1–#8 Custom Code and Data Codes ............................................................................................25

6. Ethernet Serial Interface .......................................................................................................................................................28

7. RS-232 Serial Interface .........................................................................................................................................................29

8. Ethernet TCP Setup Guide ...................................................................................................................................................30

9. Troubleshooting ...................................................................................................................................................................31

9.1 Contacting Black Box...................................................................................................................................................31

9.2 Shipping and Packaging .............................................................................................................................................. 31

724-746-5500 | blackbox.com

Page 7

Chapter 1: Specifications

1. Specifications

Technical Specifications

Approvals CE, FCC, RoHS, REACH

Audio Support Supports DVI-Audio input and SPDIF output

Controls IR remote control,

IR external port with (1) 3.5-mm earphone jack,

Select and Function buttons on front panel,

RS-232 or Ethernet series interface,

(8) IR room remote controls

Color Black

Digital Audio

Support

Multi audio formats 5.1/7.1, MAT (MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES-6CH,

DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)

Digital Video

Support

HD: 480i, 480p, 720p, 1080i, 1080p, up to 36-bit deep color

Function

Control Key

ALL/OFF/RECALL/ENTER/MEMORY/LOCK/EDID

HDCP/CEC

Support

HDCP 2.0 compliant, CEC compliant

HDMI I/O

Connector

HDMI Type A, SMD 19-pin female

HDMI Support HD 1080p @ 60 Hz, H36-bit deep color, 3D (1.4a) formats

Infrared

Frequency

38 kHz

IR External

Distance

1000 feet (300 m) maximum

ESD Protection Human body model:

± 10 kV (air-gap discharge);

± 6 kV (contact discharge)

Number of

Rack Units

1U, fits in 19" rack (using the included rackmount brackets)

Source Status Automatically scan sources inputs via LED

Video

Bandwidth

Double data rates: 340 MHz, total 6.75 Gbps bandwidth

724-746-5500 | blackbox.com

Page 8

724-746-5500 | blackbox.com

Chapter 1: Specifications

Technical Specifications (continued)

Connectors AVSW-HDMI8X8-X:

Input:

(8) HDMI (sources),

(8) 3.5-mm analog audio,

(8) DB9 RS-232 for extension,

(9) IR extension ports (1 to all, 8 for each);

Output:

(8) HDMI (sinks);

(8) HDBaseT

ports (CAT6/6A/7 cable),

(8) RJ-45 CATx (HDBaseT via Category 6/6a/7 cable),

(8) SPDIF audio,

(9) IR extension ports (1 to all, 8 for each);

Control:

(1) DB9 RS-232 for serial control,

(1) RJ-45 for telnet control,

(1) IR extension port;

AVSW-HDMI-RX:

Input:

(1) HDBaseT port,

(1) IR extension port;

Output:

(1) HDMI (sink),

(1) 3.5-mm analog audio,

(1) RS-232 (control),

(1) IR extension port,

(2) RJ-45 (unused)

Environment Temperature: 32 to 100˚ F (0 to 38˚ C)

Power AVX-HDMI8X8-X, AVSW-HDMI-RX Input: 100-240 VAC, 50/60 Hz, internal power supply;

Consumption: 10 A maximum

Dimensions 1.75"H x 19"W x 9.85"D (4.4 x 48.2 x 25 cm)

Weight 7.91 lb. (4.75 kg)

2. Overview

724-746-5500 | blackbox.com

Page 9

Chapter 2: Overview

2. Overview

2.1 Introduction

The AVSW-HDMI8X8-X is a high-performance 8 x 8 matrix routing switch with (8) HDMI plus DVI-audio inputs. It supports (8)

HDMI with SPDIF audio outputs and (8) HDBaseT outputs simultaneously. The AVSW-HDMI8X8-X is based on HDBaseT

technology and supports full-resolution HDMI video with embedded audio, RS-232, and IR bi-directional signals, all over a single

CATx cable.

With a signal bandwidth of 340 MHz, there is no signal degradation. HIgh-definition digital signals can be selected and

distributed to any 16 outputs simultaneously (8 channels x 2). The switch complies with CEC and HDMP 2.0 standards, HDMI

V1.4a 3D formats, and data rates up to 6.75 Gbps. It also supports UXGA/WUXGA/DVI 1920 x 1200 resolution to any HD

displays.

The AVSW-HDM8X8-X has one CAT6/6A and HDMI connector for each output, effectively making this an 8 x 16 switch (same

signal on both outputs). One RJ-45 connection on each output extends the HDMI signal to remote locations via HDBaseT CATx

cable extended to the HDBaseT Receiver (AVSW-HDMI-RX).

You can select the EDID from eight different modes. Control the switch via front-panel push buttons, IR remote, or via RS-232 or

TCP/IP (not a Web browser).

2.2 Features

• Matrix switches (8) HDMI with DVI-audio source devices to (8) HDMI with HDMI/DVI SPDIF and (8) CATx (6/6A/7) device

extender output devices.

• Supports HDMI digital video w/embedded audio, DVI format, and complies with CEC/HDCP 2.0.

• Includes (7) function key controls.

• Supports worldwide EDID modes for HDTV resolutions.

• Enables link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), and supports HDMI 1.4a 3D formats.

• Supports DVI audio input and SPDIF (LPCM 2-CH or maximum 5.1CH output).

• Works with wide range of HD resolutions from PC XGA to WUXGA 1920 x 1200 and HDTV/TV resolutions 480i/480p,

576i/576p, 720p, 1080i, and 1080p.

• Compatible with all HDMI source devices, PC monitors, plasma HD displays, HDTV, and audio receivers/amplifiers.

• Provides digital video TMDS formats resolution up to 1080p-60 with deep color 36-bit.

• Supports digital audio: Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2,

LPCM2.

• Choose from four ways to control the user interface: Windows based GUI control via TCP/IP port (not a Web browser), front-

panel push button, IR wireless remote control, and third-party RS-232 controller (via simple ASCII).

• Supports worldwide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK.

• Supports EDID modes:

- Embedded EID modes: FSS/H24-3D-M/H36-3D/H36-3D-M/DVI-D 1280x1024–60 Hz/DVI-D 1920x1200—60 Hz/AUTO.

- External modes: Learning mode.

• Front-panel LEDs automatically show active input and output status.

• Supports IR Remote and IR Extender with distance up to 1000 feet (300 m) maximum.

• Provides EDID configuration via Internal modes.

724-746-5500 | blackbox.com

Page 10

724-746-5500 | blackbox.com

Chapter 2: Overview

• Consumer Electronic Control (CEC) switch can be all open or OFF.

• Remembers the last state during a power cycle.

• When power is removed and resorted, the last configuration will be restored.

2.3 What’s Included

Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support

at 724-746-5500 or info@blackbox.com.

AVSW-HDMI-8X8-X includes:

• (1) XR 8 x 8 HDMI Matrix Switch with Audio

• (1) power cord

• (1) DB9 male-female cable

• (9) remote controls (1 main, 8 receiver remotes)

• (1) IR extender receiver kit

• (4) IR transmitter cables

• (4) IR receiver cables

• (4) IR extender transmitter sets

• (4) IR extender receiver sets

• (1) RS-232 Cable

• (1) 19" rackmounting kit

• (1) CD-ROM containing this user’s manual in PDF format

AVSW-HDMI-RX includes:

• (1) XR HDMI Matrix Switch Receiver

• (1) 12-V, 2-A power supply w/cord

• (2) IR cables (1 in, 1 out)

2.4 Hardware Description

Figure 2-1 shows the front panel of the switch, and Figure 2-2 shows its back panel. Tables 2-1 and 2-2 describe the

components.

2.4.1 Front Panel of the AVSW-HDMI8X8-X

1 2 3 4 5 6 7 8 9 10 11

12 13 14

Figure 2-1. Front panel.

724-746-5500 | blackbox.com

Page 11

Chapter 2: Overview

Table 2-1. Front panel components.

Number Component Description

1 Power Switch

The power switch turns the unit on and off. The LED will light red to indicate that the switch is on

and is receiving power. The switch will remember that last state during a power cycle. When

power is removed and restored, the last configuration will be used.

2 Output Status Display Each output (destination) channel shows which input (source) is assigned.

Function Key — RECALL

The system will show previously stored presets, up to a total of 16. Presets are stored in local

memory using Source keys 1 through 8 or Destination keys 1 through 8 as the memory preset

location.

• Press the RECALL button.

• Press 1 through 8 in either Source or Destination row.

• Press ENTER. The preset configuration will execute. Operation completes.

NOTE: Operation will abort if no keys are pressed within 5 seconds.

Function Key—MEMORY

The system will store presets, up to a total of 16. Presets are stored in local memory using

Source keys 1 through 8 or Destination keys 1 through 8 as the memory preset location.

• Configure desired matrices.

• Press the MEMORY button.

• Press 1 through 8 on either Source or Destination row.

• Press ENTER to ready memory location.

• Or press MEMORY again to cancel operation.

Operation completes.

NOTE: Operation will abort if no keys are pressed within 5 seconds.

Function Key — LOCK

• Press and hold the LOCK button for two seconds to lockout the front panel.

• Press and hold the LOCK button for two seconds to re-enable the front panel.

6 EDID Mode Select Buttons

Select EDID mode using Buttons #1 and 2.

7 Source Select Buttons

Separate inputs 1 through 8 select buttons are provided for each source selection.

Function Key — EDID

Press EDID to select new EDID mode and select source button #1 or #2 to change embedded EDID

mode.

Press the Destination number to learn EDID. The Destination EDID has been learned.

Press the Destination number multiple times to switch between local and HDBaseT EDID.

724-746-5500 | blackbox.com

Page 12

724-746-5500 | blackbox.com

Chapter 2: Overview

Table 2-1 (Continued). Front panel components.

Number Component Description

Function Key — ALL

Disables (mute) video on all destinations OR selects the same source to all destinations.

Option 1: Press ALL followed by the OFF button. The display will show “0,” indicating that all destinations

have no video selected.

Option 2: Press ALL followed by Source 1 through 8. The display will show the source selected.

Press ENTER and the preset source selection will be assigned to all destinations.

Function Key — OFF

Disables (mutes) video to selected channels.

• Press the OFF button followed by any destination channel.

• Press button 1 through 8 to select the output destination. The display will show “0” for the selected

channel indicating no video selected.

11 Function Key – ENTER

Press the ENTER key to confirm entries.

12 Input Status Display Input source 1 to 8 LED lights blue to indicate that a video source is present on that input.

13 IR Sensor

The IR sensor receives IR commands from the supplied remote control or third-party emitter.

14 Destination Select Buttons

Separate outputs 1 through 8 select buttons are provided for each destination assignment. Routing can

be source to destination or one source to multiple destinations.

Example: Press Destination 1, 3, 5, then press Source 2. The switch will route Input 12 to Output 1, 3,

5, respectively.

15 (not

shown)

19" rackmount brackets

Brackets included to install the switch in a 19" rack. (Brackets not shown in Figure 2-1; they attach to

the sides of the switch.)

724-746-5500 | blackbox.com

Page 13

Chapter 2: Overview

2.4.2 Rear Panel of the AVSW-HDMI8X8-X

2 3 4 5 12 7 8 9 10 11

6 13 14

Figure 2-2. Rear panel.

Table 2-2. Rear panel components.

Number Component Connector Connector Descripton Component Description

1 Outputs 1–8 HDMI

HDMI out

HDMI digital video/audio connector

with fix screw.

NOTE: With the proper adapters, you

can use the switch with DVI digital

video signals. HDCP compliant.

Connect a signal link of HDMI direct digital video/audio to this

female HDMI connector. The connector supports HDMI digital

video/audio and DVI digital video sources.

2 Inputs 1–8 HDMI

HDMI in

HDMI digital video/audio connector

with fix screw.

NOTE: With the proper adapters, you

can use the switch with DVI digital

video signals. HDCP compliant.

Connect a signal link of HDMI direct digital video/audio to this

female HDMI connector. The connector supports HDMI digital

video/audio and DVI digital video sources.

3 3.5-mm audio jack

Analog audio in

DVI audio

Connect an analog audio input when used with DVI digital

video sources. The audio will be embedded into the HDMI

signal.

4 Inputs 1–8 audio

SPDIF out

SPDIF: Use RCA connector with

HDMI or DVI digital audio signals

output.

Connect SPDIF digital audio output to an audio amplifier.

5 Outputs 1–8 HDBaseT

RJ-45 out

HDBaseT output

Connect CAT6/6A/7 to AVSW-HDMI-RX unit for HDBaseT

extension.

6 (8) DB9 connectors

RS-232 ports 1–8

connections to

control room

Remote port:

DB9 female connector

Eight RS-232 control ports interface to a PC, such as a

computer, or touch panel control, to the switch via this DB9

female conector for serial RS-232 control through the HDBaseT

receiver.

724-746-5500 | blackbox.com

Page 14

724-746-5500 | blackbox.com

Chapter 2: Overview

Table 2-2 (continued). Rear panel components.

Number Component Connector Connector Descripton Component Description

7 RS-232 Connection

Remote port: DB9 female connector

RS-232 control port enables interfacing a PC, computer, or touch panel

to the switch via the DB9 female connector for serial RS-232 control.

NOTE: The Ethernet port and RS-232 port cannot be used

simultaneously. Any connection to the Ethernet port will disable

serial commands sent to the RS-232 port.

8 Ethernet Connection

Control the switch, RJ-45 female

connector

The Ethernet control port enables TCP interfacing to a PC or media

control system (not a Web browser) to the switch via the RJ-45

connector to control the matrix switch.

NOTE: The Ethernet port and RS-232 port cannot be used

simultaneously. Any connection to the Ethernet port will disable

serial commands sent to the RS-232 port.

IR Extender Control

IR extender jack:

Female jack:

inner OID 3.5-mm

Support one IR Extender. When you plug the external IR extender into

the switch, the front panel IR receiver remains active.

10 AC Power Inlet

3-prong power plug

Power plug:

Power input: 100–240 VAC,

50/60 Hz, 10 A

The switch has an AC power plug input connector.

11 (1) IR extender jack

IR all out: IR signal from

room

IR extender jack:

3.5-mm female connector

IR all out: IR signal from room

Support eight IR remote signals from eight rooms via ALL OUT port.

Extend cable distance up to 1000 feet (300 m) maximum. When you

plug the CAT5e/6/7 IR extender into the external port, the room IR

receivers remain active.

12 IR remote inputs 1–8

Ports 1–8 IR signal to

room

IR signal to room:

IR Extender 3.5-mm jack

Support eight IR extenders to control signals to eight rooms. Extend

cable distance up to 1000 feet (300 m) maximum. When you plug the

CAT5e/6/7 extender into the external port, the room IR receiver

remains active.

13 IR remote output

Ports 1–8 IR signal from

room

IR extender jack:

3.5-mm female

Supports eight IR extenders to receive signals from eight rooms. Extend

the cable distance to 1000 feet (300 m) maximum. When you plug the

CAT5e/6/7 IR extender into the external port, the room IR receiver

remains active.

14 (1) IR extender jack

IR all in: IR signal to room

IR extender jack:

3.5-mm female

Supports eight IR remote signals to control eight rooms via ALL IN port.

Extends cable distance up to 1000 feet (300 m) maximum. When you

plug the CAT5e/6/7 IR extender into the external port, the room IR

receiver remains active.

724-746-5500 | blackbox.com

Page 15

Chapter 2: Overview

2.4.3 Front and Rear Panels of the AVSW-HDMI-RX

1 2 3 4 5 6

Figure 2-3. AVSW-HDMI-RX front panel.

7 8 9 10 11

Figure 2-4. AVSW-HDMI-RX back panel.

Table 2-3. AVSW-HDMI-RX components.

Number Component Descripton

1 HDCP LED Lights when HDCP video is connected

2 Link LED Lights when linked to the switch

3 Power LED Light when power to the receiver is on

4 IR Used with remote to switch this output only

5 IR in port To switch

6 IR out port From switch

7 Power connector Links to 12-VDC power supply

8 RJ-45 connector HDBaseT in

9 HDMI connector HDMI out

10 3.5-mm connector Audio out

11 DB9 connector RS-232 port for extension

724-746-5500 | blackbox.com

Page 16

724-746-5500 | blackbox.com

Chapter 3: Installation

3. Installation

3.1 Installation Diagram

Figure 3-1 shows a sample application using the 8x8 HDMI Matrix Switch

(AVSW-HDMI8X8-X) and the Receiver (AVX-HDMI-RX).

Receiver

(AVSW-HDMI-RX)

Monitor

Remote

8 x 8 HDMI Matrix Switch

with HDBaseT

(AVSW-HDMI8X8-X)

Remote

HDMI

projector

Speaker

HDMI

out

Audio

amplifier

HDMI player

HDMI

Audio

Figure 3-1. Typical application using the 8 x 8 HDMI Matrix Switch.

HDMI

Close-up showing input

and output connections

Audio

out

HDMI

out

724-746-5500 | blackbox.com

Page 17

Chapter 3: Installation

3.2 IR Extender

Figure 3-2. IR extender connection.

NOTE: When you plug the external IR extender into the switch, the front panel IR receiver remains active.

Figure 3-3. How to set up the IR extender components: Steps 1-3

IR extender to room

IR receiver (for 320 feet [100 m])

IR receiver (included)

Room

724-746-5500 | blackbox.com

Page 18

724-746-5500 | blackbox.com

Chapter 4: Operation

4. Operation

4.1 EDID Setup

Table 4-1. EDID function setup for HDMI matrix switch: change the EDID setup.

Step

Number Action Result

Step 1 Press the EDID button.

The display will show the currently selected EDID mode.

Step 2

Press the SOURCE #1 or

#2 button row

The button will flash blue and the display will show the current Embedded EDID status.

Step 3 Press the ENTER button Set EDID mode. The switch will return to operation mode.

NOTE: Operation will abort if no keys are pressed within five seconds.

4.2 RESET

Table 4-2. Reset function for HDMI matrix switch.

RESET EDID return to factory default

To Reset EDID mode:

Press EDID > RECALL > ENTER

1. Reset to the factory default (1080p–2CH).

2. Press the EDID button. The LCM will show the current EDID status.

3. Press the RECALL button. The LCM will show the RESET EDID.

4. Press the ENTER button to confirm the entries. The EDID will return to FSS mode and resolution 1080p-2CH.

724-746-5500 | blackbox.com

Page 19

Chapter 4: Operation

4.3 Embedded EDID Modes

Table 4-3. EDID function for HDMI matrix switch: select embedded EDID mode or LEARNING mode.

Embedded EDID modes Total 8 EDID modes

Embedded EDID setup

Press EDID > SOURCE > ENTER

Select Embedded EDID mode or LEARNING mode.

1. Press the EDID button. The LCM will show the currently selected EDID mode.

2. Repeatedly pressing the Source 1 button will cycle UP through the options. Repeatedly pressing the Source 2 button will

cycle DOWN through the options.

3. Select Embedded EDID:

Mode 1: FSS Mode 5: H36-3D-M

Mode 2: H24-3D Mode 6: DVI-D 1280 x 1024—60 HZ

Mode 3: H24-3D-M Mode 7: DVI-D 1920 x 1200—60 HZ

Mode 4: H36-3D Mode 8: AUTO

4.4 LEARNING EDID

Table 4-4. LEARNING EDID function for HDMI matrix switch.

LEARNING EDID Learning EDID form Destination to Source

LEARNING EDID setup:

Press EDID > DESTINATION > SOURCE > ENTER

Press EDID > DESTINATION button: The LCM will show LEARNING.

The switch will learn the destination EDID and pass the selected source.

NOTE: The already learned EDID cannot be modified. You can only rebuild a new

Learning EDID.

For example, when the Source has “Learned” the EDID data from a Destination, it

will save that EDID information into EPROM and the EDID data cannot change.

To remove the learning EDID memory from EPROM, select new learning destination

to sources or change one of the embedded EDID modes.

724-746-5500 | blackbox.com

Page 20

724-746-5500 | blackbox.com

Chapter 4: Operation

4.5 EDID Function for HDMI Matrix Switch

Table 4-5. Embedded EDID modes.

Mode

Number Embedded EDID Setup Description

Mode 1

FSS (Fast Speed Start)

Video support: All resolutions up to and including 1080p.

Automatically capture the most suitable EDID from Destination to Source.

Mode 2

H24-3D (1080p–24 bits)

Video support: All resolutions up to and including 1080p.

Audio support: PCM 2CH

Mode 3

H24-3D-M (1080p–24 bits)

Video support: All resolutions up to and including 1080p.

Audio support: MAT (MLP) 7.1CH, PCM 2CH, one bit audio 2CH, AC3 5.1CH, DTS 5.1CH, PCM 7.1CH,

Dolby Digital +7.1CH, DTS-HD 7.1CH

Mode 4

H36-3D (1080p–36 bits)

Video support: All resolutions up to and including 1080p.

Audio support: PCM 2CH

Mode 5

H36-3D-M (1080p–36 bits)

Video support: All resolutions up to and including 1080p.

Audio support: MAT (MLP) 7.1CH, PCM 2CH, one bit audio 2CH, AC-3 5.1CH, DTS 5.1CH, PCM 7.1CH,

Dolby Digital +7.1CH, DTS-HD 7.1CH

Mode 6

1280 x 1024-60 Hz (DVI-D)

DVI support: DVI-D 1280 x 1024, 60 Hz

Mode 7

1920 x 1200-60 Hz (DVI-D)

DVI support: DVI-D 1920 x 1200, 60 Hz

Mode 8

AUTO <Default>

Video support: All resolutions up to and including 1080p.

All outputs will be set to the highest common resolution of all connected display devices.

Page is loading ...

Black Box AVSW-HDMI-RX User manual

Brand: Black Box

Model: AVSW-HDMI-RX

Category: Video switches

Type: User manual

This manual is also suitable for

Download PDF

report

Black Box AVSW-HDMI-RX User manual

This manual is also suitable for

Black Box AVSW-HDMI-RX User manual

Related papers

Other documents