POSIFLEX Business Machines PP-8000L User manual

Brand: POSIFLEX Business Machines

Model: PP-8000L

Category: Multifunctionals

Type: User manual

This manual is also suitable for

Part 1

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause interference to radio communications.

It has been tested and found to comply with limits for a Class A digital device pursuant to subpart

J of Part 15 of FCC Rules, which are designed to provide reasonable protection against

interference when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference in which case the user at his own expense will be

required to take whatever measures to correct the interference.

CE manufacturer’s Declaration of Conformity

(EC Council Directive 89/336/EEC of 3 May 1989)

This product has been designed and manufactured in accordance with the International Standards

EN50081-1/01.92 and EN50082-1/01.92 following the provisions of the Electro Magnetic

Compatibility Directive of the European Communities as of May 1989

Warranty Limits:

Warranty terminates automatically when any person other than the authorized technicians opens

the machine. The user should consult his/her dealer for the problem happened. Warranty voids if

the user does not follow the instructions in application of this merchandise. The manufacturer is by

no means responsible for any damage or hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex

will assume no liability for any technical inaccuracies or editorial or other errors or omissions

contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including

without limitation loss of data or profits, resulting from the furnishing, performance, or use of this

material.

This information is provided “as is” and Posiflex Technologies, Inc. expressly disclaims any

warranties, expressed, implied or statutory, including without limitation implied warranties of

merchantability or fitness for particular purpose, good title and against infringement.

The information in this manual contains only essential hardware concerns for general user and is

subject to change without notice. Posiflex reserves the right to alter product designs, layouts or

drivers without notification. The system integrator shall provide applicative notices and

arrangement for special options utilizing this product. The user may find the most up to date

information of the hardware from web sites: http://www.posiflex.com

http://www.posiflex.com.tw

or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage peripheral.

Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this

or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a

retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,

or otherwise, without prior express written consent from Posiflex Technologies, Inc. the publisher

of this documentation.

All brand and product names and trademarks are the property of their respective holders.

Aura Series

PP-8000 / PP-8000L / PP-8000U

THERMAL PRINTER

USER’S MANUAL

Rev.: A0

P/N: 19770900020

Part 2

GETTING STARTED

CONGRATULATION

You have made a very wise decision by purchasing the easy loading;

low noise; high resolution; light weight; high reliability and high performance

thermal printer Aura (PP-8000, PP-8000L & PP-8000U) series of Posiflex

products. This series of printers has been elegantly designed for a Point-Of-

Sale, kitchen & kiosk application. The PP-8000 series comply with UPOS 1.8

standards under Posiflex UPOS driver support. The manufacturer of this

printer not only wishes to take this opportunity to congratulate your smart

investment on buying this printer but also likes to express the wishes for your

prosperous future by using it.

PRODUCT BRIEFING

The Aura PP-8000, PP-8000L & PP-8000U series printer uses

thermal sensitive paper in form of a roll at a width of 80 mm (standard) or 58

mm (option). These Aura series printers serve the stand-alone desktop

application as well as the application within a Posiflex integrated POS system

equally perfect.

The Aura PP-8000 series support two types of interface input through

different sub-codes to the model number. The interfaces are RS232 for serial

interface and Centronics for parallel interface. The Aura PP-8000L series

connects to a LAN port of Posiflex POS systems. The Aura PP-8000U series

connects to an USB port of Posiflex POS systems and simulates a RS232

device through driver and performs thermal printing particularly designed for

POS applications. The Aura PP-8000 series is already WEPOS (Windows

Embedded for Point Of Service) compliant. Aura printer of different model

number sub-codes utilizes different cabinet color and accessory cable and

switch setting to accommodate the requirement of different interface.

The Aura PP-8000 series support a guillotine type auto cutter for

paper partial cut and a manual cut mechanism. The Aura series also supports

user’s company’s LOGO downloading for superior performance. It even

supports some enhancement capability for reminder function to persons around.

It can be used to drive a separately purchased kitchen bell for such reminder

function in noisy environment. This printer also supports application in

different countries of various kinds of power systems by changing the power

cord to the power adaptor. It offers outstandingly high printing speed. This

series make beeping sound as response to Paper End or Paper Near End signals.

20 plus code pages are supported in the standard model for application

convenience.

Part 3

UNPACKING

Followings are items you may find when you carefully unpack the

carton that delivers Aura series printer. If there is any discrepancy or problem,

contact your dealer immediately. Be sure to save the packing materials in

case the printer needs to be shipped at some point in the future.

1). The printer itself

2). Thermal paper test roll 80 mm wide

3). One piece of spacer plate

4). One of the interface cables:

a. Serial cable with 9 pin D sub Female to 9 pin D sub Male

connectors for Aura PP-8000 serial model

b. Parallel cable with 25 pin D sub Male to 25 pin D sub

Female connectors for Aura PP-8000 parallel model

c. No interface cable for PP-8000L

d. USB cable for Aura PP-8000U

Length of the interface cable depends on whether the order includes

the power adaptor. When power adaptor is included, the interface cable is 6 ft

long for stand alone application. When the power adaptor is not included in the

order, the interface cable is a shorter one for integrated application in Posiflex

POS system.

5). One of the power sources:

a. Power adaptor + power cord (depend on country type

ordered)

b. Power supply cable (when no power adaptor and no

powered USB cable ordered)

6). This User’s Manual

OPTIONS

 Spill protect cover (P/N: 19770300013/6)

 58 mm paper spacing plate (P/N: 19770305013/6)

 Kitchen bell (Alarm type KL-100 or buzzer type KZ-200)

 Language to add to standard model: Japanese Kanji, Korean, Simplified

Chinese or Traditional Chinese

 Wall mount kit

Part 4

PRODUCT PICTURES

Top View

Front View

Bottom View

Bottom Cover

Power Switch

Power LED

Error LED

Paper Out LED

FEED Switch

Top Hood

Top Cover

Hood Release

Cutter Cover

Paper Exit

Rubber Foot

Window Plate Screw

Setup Window Plate

Wall Mount Hanging Hole

Rubber Foot

Part 5

Rear View

Spill Protect Cover

INDICATORS

 Power LED: green

 Error LED: red (brief lit indicates printer busy)

 Paper Out LED: red

Paper Exit

Serial Port

Peri

heral Port

Parallel Port

Frame Ground Screw

Power Connecto

USB Port

LAN Port

Reset Pin Hole for LAN

(I/O Area for PP-8000U)

(I/O Area for PP-8000L)

USB Adaptor

Fixation Screw

(

I/O Area for PP-8000

)

Part 6

QUICK START-UP

LOADING PAPER

Desk Top Application

1. Remove the spill protect cover if the option is on.

2. Press down the hood release button to release the top hood as in Pix. 1.

3. Raise the released hood wide open manually as in Pix. 2.

4. Drop the thermal paper roll inside the printer in orientation as shown in

Pix. 2.

5. Close the hood back leaving the tail of the paper roll coming out of the

opening between the hood and the top cover as in Pix. 3.

6. Apply the spill protect cover while having the paper to come out of the

paper exit slot of the cover if this option is used.

7. Tear off excessive paper.

When to Replace Paper

Whenever the printer gives paper out signal or a red line appears on

the thermal paper, it is the proper timing for replacing the paper. Do not wait

till the print engine is dragging the paper roll at the very end. Remove the

leftover and replace a new paper roll as illustrated above to prevent excessive

paper dust in the printer and consequently possibility for paper jam.

CONNECTING CABLES

Serial Connection

All the external connectors are in the recessed area at the rear

bottom

for PP-8000 series. The serial connector is a 9-PIN D sub Female connector at

the right in this area. Apply the male connector of RS232 cable to this port for

serial application. Please note that when serial connection is used, there must

be no cable connection at the parallel port on the printer. The default protocol

used in serial connection is 115,200 bps, none parity, 8 data bits, 1 stop bit. Set

Release Button

Pix. 1

Pix. 2

Pix. 3

Part 7

in setup window the switch position 1 to OFF, and position 2 to ON leaving

the rest unchanged as factory default setting.

Parallel Connection

The parallel connector is a 25-PIN D sub Male connector at the

leftmost location in the connector area for PP-8000. Apply the female end of

the parallel cable at this port for parallel application. Please note that when

parallel connection is used, there must be no cable connection at the serial port

on the printer. Please also note that to keep parallel interface in fast operation,

please adjust in setup window the switch position 1 to OFF, and position 2 to

ON leaving the rest unchanged as factory default setting.

LAN Connection

The LAN connector is a 8-PIN RJ45 type modular connector at the

position left to the power connector in the connector area for PP-8000L. Please

use a LAN cable of CAT 5 with proper length to connect the LAN connector

on the printer to the LAN HUB as appropriate. Please note that for PP-8000L,

there must be no cable connection at the serial port or the parallel port on the

printer. Please also note that to keep LAN interface operative, please adjust in

setup window the switch position 1 to OFF, and position 2 to ON leaving

the rest unchanged as factory default setting. DO NOT CONNECT THE

PERIPHERAL DEVICE TO THIS PORT!! The LAN port is 10/100BaseT

compliant.

USB Connection

The USB connector on PP-8000U is a

type B USB connector at lower right position

below the serial port. Use the normal USB Cable

(P/N: 21863250800) as in the left picture to

connect the type A end to a normal USB port of

host system. Please visit our web site

http://www.posiflex.com

http://www.posiflex.com.tw

for detailed information of the USB driver

installation if required. Please note that for PP-8000U, there must be no cable

connection at either the serial port or the parallel port on the printer. Set in

setup window the switch position 1 to OFF, and position 2 to ON leaving

the rest unchanged as factory default setting.

Peripheral Connection

The peripheral controller is a 6 pin RJ11 type modular jack. With use

of Posiflex cash drawer cable 21863018010 (CCBLA-180-1) come with cash

drawer, this port can control a Posiflex cash drawer CR3100 or CR3200 or

CR4000 or CR4100 or CR-6310. If a Posiflex special split cable 21863023800

Type A

Normal USB Plugs

Type B

Part 8

(CCBLA-238) is used instead, this port can control two cash drawers of above

models.

When the printer is used as a kitchen printer, please use this port for

kitchen bell connection instead.

Power Connection

The power connector is a 3-PIN jack between the peripheral

connector and the parallel connector for PP-8000. Either a Posiflex supplied

power adaptor or a printer power cable from a Posiflex POS system can be

connected to this connector to supply power for this printer. During insertion

of the power plug, be sure to hear the click to obtain a firm contact.

CAUTION: Before doing the insertion or extraction of the power plug, be

sure to pull the outer sleeve of the plug backward to release the

internal latch. Failure to do this could damage the power plug. Such

damage is considered as an artificial destruction and is not covered

by the warranty.

Power On

When all the above cable connections are made correctly, you may

connect your power adaptor to the wall

outlet. Make sure that the type of

power cord and the voltage

requirement of the power adaptor meet

the local power conditions. Now the

printer is ready for power on.

Self Test

Press and hold down the feed

button while turning the on / off switch

on. The printer will then perform a

self-test. A sample slip of self-test

result is printed as in the sample at

right. Please note that both serial and

parallel interfaces are indicated. That

means the printer is working on an

auto-sensing and auto-select algorithm.

The header is printed in text

mode and the rest part of this slip is

printed in page mode. If FEED button

is pressed at this moment, a font table

will be printed in text mode again. To

exit the test printing, please turn the

printer off and on again.

Part 9

SPECIAL ADJUSTMENTS

Paper Near End Sensor

The near end

sensor for paper roll

in the printer is able to

have the printer work

with paper rolls of

several bobbin sizes.

Please refer to the

picture at right for the

inside of the paper roll

compartment that there are a plastic thumb wheel for bobbin size adjustment

and a sensor block in the wall. Turn the thumb wheel to adjust the proper

position of sensor block. For desktop application, the sensor block should be

above the bobbin seating on the 2 support rollers on bottom of paper

compartment when paper near end.. The acceptable paper roll bobbin outer

diameter is between 18 and 24 mm.

58mm Paper Spacing Plate

The application of 58 mm width paper roll in this printer can be

achieved through adoption of an option spacing plate and an internal DIP

switch setting. Please refer to the last chapter of this manual for the DIP switch

setting. Please refer to the middle picture above for the 58 mm paper spacing

plate with its flange at top edge showing out. Insert the noted corners of the

spacing plate into the 3 dents inside the paper roll compartment as arrowed in

the left picture above with point A goes in first. Then the 58 mm paper roll sub

compartment is formed as in the right picture above.

Paper Cutting

The paper advance after a normal cut with auto paper feed is set to 12

mm. In case the user applies cut without paper feed through DIP switch setting

change to have something like a logo printed on top of each slip, it is also

highly suggested to print the logo and necessary paper feeding to make 12 mm

paper advance right after each cut to prevent curling up and jamming of paper

Sensor Block

Sensor Position Adjust

Support Roller

Paper Roll Shaft Hold

58 mm

Compartment

Part 10

front edge inside the paper exit slot.

INSTALLING DRIVER

There will always be a Posiflex Product Information CD or DVD or a

separate CD of similar nature but specifically created for the product delivered.

Please find the appropriate subfolder from the non-specific Posiflex Product

Information CD or DVD and check the information file like “readme” or

installation guide or application guide and follow the instructions inside.

LAN PRINTER SPECIFIC ISSUES

Web Manager

The default static IP for the PP-8000L is 192.168.192.168 and default

listen port is 9100. User may set his own IP to the same network segment and

use any browser to connect to the printer IP to configure the LAN setup of the

PP-8000L including changing the printer IP for application according to his

network administrator’s request. However, DHCP is not supported.

Reset Pin Hole

As the LAN setup for the PP-8000L can be set freely, if the changes

are not well registered some troubles could be introduced. Therefore, in PP-

8000L, there is a “Reset pin hole” near the LAN connector. Use something like

a ball pen tip or straightened end of paper clip to push and hold for at least 5

seconds into this hole will reset the LAN setup of the printer back to the

default values at delivery so the user may re-do all setup. The LAN setup can

be viewed in second paragraph of self-test printout for the PP-8000L.

LAN POS Printer Manager

This utility can be used to manage multiple PP-8000L’s connected in

same network under Windows as long as there is no conflicting IP in the

network. This utility can assign to each LAN printer a different device name

for easy recognition. In case of confusion, please check the MAC addresses

listed in this utility against the MAC address label you can find under each

printer.

Printer Driver Setup

Any PC connected in same network can use TCP/IP to use PP-8000L

in the way like a directly connected local printer. So, for direct I/O control by

tools like “HyperTerminal” all commands applicable to the serial or parallel

interface model can work on PP-8000L in the same way as PP-8000 except the

port must be TCP/IP with the IP address of the printer. Similarly, for Windows

printer driver setup, please “Add Printer” and select for “Local printer” and

select port “TCP/IP” with the printer IP address then use the same Windows

printer driver of PP-8000 for PP-8000L.

Part 11

OPERATION GUIDE

MAINTENANCE GUIDE LINES

 Always turn off and disconnect power before opening the cover.

 The areas around the print head and motor become very hot during and just

after printing, DO NOT touch them.

 When handling the interior of the thermal printer, please pay attention not

to be hurt by any sharp edge of the metal parts.

GENERAL CLEANING

Please use soft hairbrush or compressed air to clear away any dust or

paper scraps accumulation inside the printer. Check also the area of the auto-

cutter regularly.

PRINT HEAD CLEANING

The print head is located underneath the roll paper passage at the exit

as in the picture below. You can clean the thermal elements of the print head

and paper sensor gently using a cotton swab moistened with isopropyl alcohol

solvent.

NOTE: Never do this when print head is still hot

Do not touch the print head thermal elements

Do not scratch the print head

Before putting back the paper roll for printing, alcohol solvent must

be dried completely.

TROUBLE SHOOTING

This section gives solutions to some printer problems you may have.

General Problems

No LED lights up on control panel when switched on –Make sure

that the power supply cables are correctly plugged into the printer, the power

adaptor and to the power outlet. Make sure that power is supplied to the power

outlet. If the outlet is controlled by a switch or timer, try use another outlet

Thermal Elements

Paper Sensor

Part 12

Printing Problems

Nothing can be printed with ERROR LED flashing – Most

possible cause for the flashing Error LED is that the printer has been printing

for quite a period of time and the print head temperature become too high.

After few minutes under normal ventilation, the print head should be able to

cool down and the Error LED will stop flashing. Printing will resume after

cooled down. If this is not the case, contact a qualified service person.

Nothing can be printed with ERROR LED ON – Check the Paper

Out LED. If it is ON, most probably either the paper roll is not installed or the

paper roll is at or near the end. Install a new paper roll. If the Paper Out LED is

OFF, please check if the print hood is properly closed. There are 2 internal

check points inside the printer to assure the locking of the hood for a decent

printing. Therefore any dislocation of the hood may cause an error status and

inhibition to printing. Press down the hood at middle of the opening when

closing it till it audibly clicks into place. If both situations are not the cause,

please try pulling the hood lock forward. If the top hood won’t release

automatically, check for paper jam described in next item.

If there is no paper jam and the print head is not overheated, turn off

the printer and wait for half a minute then turn it back on. If the problem still

remains, contact a qualified service person.

Nothing can be printed with ERROR LED OFF – Try to run self-

test according to previous chapter to check if the printer itself works properly.

If the self-test passes, check the following:

1). Check the connection of the interface cable at both the

printer and computer ends. Also make sure that this cable

meets the specification required for both the printer and the

computer.

2). Check the printer data communication settings against the

computer. The printer settings can be found easily on the

self-test print out.

If the problem remains or the self-test fails, contact your dealer or a

qualified service person.

Poor printing quality – Contaminants like paper scraps and dusts on

the thermal print head can lower the print quality drastically. Clean the print

head as described in previous section.

Paper Jam Problems

Paper is jammed inside the printer – Turn off the printer and open

the top hood by releasing the hood lock. Remove the jammed paper and

reinstall the paper roll. Close the hood properly and firmly. Then turn on the

printer for operation.

If the auto cutter is jammed, the top hood will be locked. Please first

Part 13

resolve the auto cutter problems per description in next item and then come

back to deal with the paper jam. Never force open the top hood. Please also

clear away any contaminants accumulated in the cutter track above the thermal

elements.

Auto Cutter Problems

In case any foreign materials like a staple or paper clip or excessive

paper scraps fall into the auto cutter mechanism the auto cutter may lock up

and so does the print hood. In such case, please pull the cutter cover forward to

expose the cutter adjustment area. Apply some mechanical assistance in below

procedures to help resetting the cutter blade back to its home position. Please

lift up a transparent protective cover over the adjustment wheel with the printer

powered off. Turn this wheel downward for 4 or 5 strokes. Close the cutter

cover back and turn the printer power on to see if the auto cutter lock up

problem is resolved.

If the problem is not automatically resolved by above procedures,

please power off the printer and open the cutter cover again. Check in the

alignment window while turning the gear downward as above or with a small

Phillips screwdriver at the right side of the cutter mechanism. When the cutter

blade returns to its standard position, a hole in the white plastic gear will show

up in the window as illustrated in detailed picture above. Close the cutter cover

Auto Cutter Track

Thermal Elements

Open Cutter Cover

when hood locke

Lift transparent

protective foil

Alignment window

Adjustment area detailed below

Use screwdriver

Turn the adjustment wheel

downward for few strokes

Part 14

when finish. The lock up of the print hood can then be released after this

problem solved.

Please use manual cutter as temporary alternative measure once the

auto cutter malfunctioned.

Advanced Analysis Tool

This printer supports Hexadecimal Dump for experienced user to

view exactly what data is received by the printer. This can be useful in finding

software problems.

To start the dump mode: Turn off printer; Open print hood; Hold

down FEED button while turning printer on; Close the hood.

To stop the dump mode: Press the FEED button to print out the last

line; Turn off the printer.

During dump mode: All commands except DLE EOT and DLE ENQ

are disabled.

USEFUL TIPS

 Please note that only those qualified technicians may adjust several

jumpers for some technical settings. Please visit our web site

http://www.posiflex.com

or http://www.posiflex.com.tw for details of the

technical information such as driver installation, DIP switch settings and

command sets etc. if required.

 Place the printer on a sturdy, level surface.

 Choose a place that is well ventilated and free of excessive dust, smoke or

fume.

 Do not put the printer under direct sunlight or near a heater.

 Ideal room temperature is from 5ºC to 40ºC. Ideal humidity is from 20% to

85% RH (no condensation).

 Do not set any liquid or drinks such as coffee on the printer case.

 Do not touch any metal part to avoid possible electrostatic damage.

 Do not touch the areas around the print head and motor during or right after

printing. It can be very hot.

 Do not allow the cut receipt to slide back into the cutter during the

operation. As this would lead to multiple cutting at the lower edge of a

receipt and the multiple cut thin slips tend to cause mechanical malfunction.

 Use a grounded AC power outlet with only the power cord and power

adaptor furnished with the printer.

 Do not use a power outlet of a circuit shared with any equipment that uses

Part 15

a lot of power or causes great electrical noises, such as a copier, electric

motors or a coffee maker.

 Do not use thermal paper containing Sodium (Na+), Potassium (K+) and

Chlorine (Cl-) ions that can harm the print head thermal elements.

 If the surface of thermal paper is scratched with a hard object such as a nail,

the paper may become discolored.

 If thermal paper touches diazzo copy paper immediately after copying, the

printed surface may be discolored.

 Use only water paste, starch paste, polyvinyl paste or CMC paste when

gluing thermal paper.

 If thermal paper touches anything containing phthalic acid ester plasticizer

for a long time, the image formation ability may be reduced or the printed

image may fade.

 Use of volatile organic solvents such as alcohol, ester and ketone or some

adhesive tapes on thermal paper can cause discoloration.

 Thermal paper must not be stored with the printed surfaces against each

other as the printing may be transferred between the surfaces.

 Since the paper roll is highly thermal sensitive, please keep them in a dark

place that is 20º and 65% RH when not installed in the printer. Avoid

extended exposure to direct light. Use only products made from

polyethylene, polypropylene or polyester for storage of thermal paper.

Part 16

SPECIFICATIONS

PRINTER

ITEM SPECIFICATION

Printing method Thermal sensitive line dot method

Effective printing width 64 mm

Thermal head configuration 512 dots / line

Printing speed 220 mm / sec. max.

Paper feed method Friction auto-feed

Paper load method Drop and use

Auto-cutter capability Partial cut (1 point at center left)

Manual cutter Saw tooth blade

Dot Pitch 0.125 x 0.125 mm

Input power type DC

Input voltage 24 V + / - 5 %

Dimension (mm) 148 (W) x 205 (D) x 143 (H)

Weight 1.2 Kg net

PAPER

PAPER TYPE THERMAL ROLL PAPER

Paper roll formation External side is heat-sensitive side

Paper width 80 (or 58) + 0 / - 1 mm

Paper roll outer diameter 83 mm max.

Paper roll inner diameter 12 + 1 / - 0 mm

Paper thickness 60 ~ 80 um

POWER ADAPTOR

ITEM REQUIREMENT

Input voltage 100 V AC ~ 240 V AC

Input frequency 50 ~ 60 HZ

Input current 1.8 A MAX. @ 115 V AC

Output voltage + 24 V DC

Output power 60 W

Static load 0 A ~ 2.5 A

Output regulation + / - 5 %

MTBF 30,000 HRS

EMI standards VDE – A, FCC – A, VCCI – A

Part 17

FURTHER TECHNICAL INFORMATION

PRINTER SETUP

On bottom cover of the Aura series thermal

printer, there is screwed a metal plate for setup window.

In this window, there is a 8 position DIP switch for

printer setup. Please use proper tool to change the

switch setting when necessary. The switch position

counting starts from the nearest edge of printer. The

ON direction points to the connector area of the printer. The OFF direction

points to the power switch. The functions of each position may evolve with the

revisions of the firmware. The information below applies to the latest version

to the date of print of this manual.

This 8 position DIP switch works as following:

Switch

position

ON OFF

RS232 baud rate definition or Parallel interface definition (ref.

separate table below)

Even parity None parity

XON/XOFF handshaking DSR/DTR handshaking

Busy on “buffer full” Busy on “buffer full” and/or “off line”

Cut without paper feed Cut with auto paper feed

CR code (0Dh) effective CR code (0Dh) invalid

Factory internal setting Application standard mode

Effect of positions 1 & 2 on baud rate is defined as in table below with

parity check set according to position 3, number of data bits always set to 8,

and stop bit set to 1. When the interface used is anything other than RS232,

please still set these 2 switches at exactly the specified combination.

SW Pos. 1

ON OFF ON OFF

SW Pos. 2

ON ON OFF OFF

Baud rate setup

38400 bps 115200 bps (Default) 9600 bps 19200 bps

Switch position 3 defines the parity check regulation in serial interface.

In Aura, it is selectable between even and none.

Switch position 4 defines the handshaking method in serial interface.

When it is set to ON, the printer transmits an “XOFF” for busy and sends an

“XON” for not busy. When it is set to OFF, the printer signifies the busy status

over hardware signals that can be detected by the host as “DSR” or “CTS”.

When parallel interface is used, both switch positions 3 and 4 should be set to

OFF.

For switch position 5, if the switch is set to ON, the busy signal is sent

Part 18

to host only when input buffer is full. When it is set to OFF, busy signal is sent

to host whenever the input buffer is full or an off line status occurs. Therefore,

signals including the paper near end detect will generate busy signal to the host.

Consequently, the printing may be stopped even when there is still a long way

to go before the paper roll is actually exhausted. Taking the paper out beep into

consideration, the printer will keep on beeping at Paper End (completely no

paper) till paper is replaced when S1-5 is ON. Yet when S1-5 is OFF, the

printer will keep on beeping every 3 seconds at Paper Near End (still long

paper in replace) till paper is replaced.

For switch position 6, when it is set to OFF, there will be a 12 mm paper

feed before cutting when software does not define this point and there will be

further 12 mm paper feeding after cutting to prevent paper jam. Before setting

this switch to ON, please make sure that your software will take care of

enough paper feed for the paper jam prevention issue.

For switch position 7, when it is set to ON, the printer responds to a

carriage return command (CR code or 0Dh) with also a line feed (LF code or

0Ah) action. Then if the text editor always express the change to a new line

with both the CR and LF codes, there will be an extra line advance than

expected. However it works for some old editors that express the change to a

new line with only either one of the LF code or the CR code.

For switch position 8, when it is set to ON in the field, the printer maybe

subject to unpredictable damages and must be strictly prevented.

The factory default for each position is listed below:

Switch Position 1 2 3 4 5 6 7 8

Default setup for all

interface models

OFF ON OFF OFF OFF OFF OFF OFF

ADVANCED SETUP

There is an extra 4 position DIP switch in PP-8000 series next to the 8

position DIP switch for more technical settings. The switch position counting

starts from the nearest side to the 8 position DIP switch.

This 4 position DIP switch works as following:

Switch position Setting Effect

Function ON OFF

Windows driver print control Immediate print Buffered print

Paper width 58 mm 80 mm

Line format (for 80 mm paper) 576 dots / line 512 dots / line

Paper auto cut at hood close Yes No

The switch position 1 defines the printing behavior of the printer on

graphic printing through use of Windows driver. When it is set to ON, the

printer prints on each printing command received immediately. However, in

Part 19

some cases, the printer may have to engage brake frequently waiting for next

command resulting in trembling. When this switch is set to OFF, the printer

starts printing only when more graphical data from Windows driver are

collected thus performing a much smoother printing operation.

Switch position 2 is usually set to OFF for use with 80 mm paper width.

When the printer is installed with the 58 mm paper spacing plate for use with

the paper roll of 58 mm width, the switch should be set to ON.

Switch position 3 is usually set to OFF for ESC/POS command

application that prints at 512 dots / line. Only technical users shall set this

switch to ON and make the printer work in the 576 dots / line format.

The switch position is recommended to set to ON when the optional

spill protect cover is used. In this way, the printer performs an automatic paper

cut each time the top hood is closed (e.g. after paper roll loading) with the

printer in operating condition. However, when there is no spill protect cover, it

is recommended to set to OFF and the manual cutter can be engaged whenever

necessary.

MULTIPLE INTERFACE ISSUE

For model PP-8000, there are 2 connectors for host connection through

RS232 or parallel. For PP-8000U, there are 3 connector for host connection:

RS232 and parallel in addition to the USB port. Please always connect only

one interface at a time. Simultaneous multiple host connections could result

in unexpected results!

UPOS CONCERNS

The UPOS compliance and WEPOS compliance ability of the PP-8000

series dictates the printer to perform certain internal affairs such as counter

refreshment periodically. When the printer is engaged in such operations there

will be a brief period of time that the printer is busy without externally

apprehensible cause. In other words, the printer will lit the ERROR LED

briefly once in a while even when no external communication is in process and

that is definitely normal.

Part 20

Wall Mount Application

In wall mount application, the option kit will include screws, plastic

cotters and a paper roll shaft. Screws and cotters are to be inserted to holes

drilled on wall 80 mm apart center to center horizontally with the non-threaded

part of the screw remain above the cotter to hang the printer bottom at holes

arrowed in the left picture below.

The paper roll shaft should go through the paper roll and seat in hold

on paper roll compartment wall as indicated by arrows in middle picture above

and the paper roll should be in the orientation as in the right picture above. The

paper near end sensor must be readjusted for wall mount application as it

approaches the paper roll from different direction for desktop application.

For wall mount application, the sensor block should be under the

bobbin supported through a shaft held on paper compartment wall

T31454

POSIFLEX Business Machines PP-8000L User manual

Brand: POSIFLEX Business Machines

Model: PP-8000L

Category: Multifunctionals

Type: User manual

This manual is also suitable for

Download PDF

report

POSIFLEX Business Machines PP-8000L User manual

This manual is also suitable for

POSIFLEX Business Machines PP-8000L User manual

Related papers

Other documents