Kenmore 385. 17624 User manual

SEARS Owner'sManual

Manual de Instrucciones

Manuel d'lnstructions

SEWING MACHINE Models

MAQUINA DE COSER Modelos _385" 17624

MACHINE A COUDRE ModUlesj385" 17620

CAUTION:

Before usingsewing machine,

read thismanual and follow

all itsSafety Rules and

Operating Instructions.

• Safety Instructions

• Warranty

• Specifications

• Operation

• Care and Maintenance

• Troubleshooting

Sears Canada Inc., Toronto, Ont., M5B 2B8

IMPORTANT SAFETY INSTRUCTIONS

Your sewing machine is designed and constructed only for HOUSEHOLD use.

Read all instructions before using this sewing machine.

DANGER - To reduce the risk of electric shock:

1. A sewing machine should never be left unattended when plugged in. Always unplug this sewing

machine from the electric outlet immediately after using and before cleaning.

2. Always unplug before replacing sewing machine bulb. Replace bulb with same type rated 15 Watts.

3. Do not reach for a sewing machine that has fallen into water. Unplug immediately.

4. Do not place or store sewing machine where it can fall or be pulled into a tub or sink. Do not place

or drop into water or other liquid.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or

near children.

2. Use this sewing machine only for its intended use as described in this manual.

Use only attachments recommended by the manufacturer as contained in this manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged or dropped into water.

Return the sewing machine to the nearest Sears store or service center for examination, repair or

electrical or mechanical adjustment.

4. Never operate the sewing machine with any air opening blocked. Keep ventilation openings of the

sewing machine and foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (" 0 ") position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch the sewing machine off (" 0 ") when making any adjustment in the needle area, such as

threading needle, changing needle, threading bobbin or changing presser foot and the like.

15. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in the instruction manual.

SAVE THESE INSTRUCTIONS

When using your sewing machine for the first few times, place a waste fabric under the presser foot

and run the machine without thread for a few minutes. Wipe away any oil which may appear.

I

Page is loading ...

_. ,_ln*_ ,,IN _ .l_n,_qb_ .LIn__ ,n_, _qb. ,_tl, _ ,_11,_ ,nil.-.qb- .nit,._ ._11,_ ._1,_ ,ll_, _ ,Iq_,_ IIn, _ '_11,-<b- 411,_ "lln, _ '_k, -'qb. ,01b.qb..._ .<b. ,_..4J..11_ .qb. ,n_ _ ',11,_ nl_ _ "LIh _ql. ,ql, .qb. '_

WARRANTY

FULL 25 YEAR WARRANTY ON SEWING MACHINE HEAD --"

For 25 years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which

• appear in the sewing machine head.T

FULL TWO YEAR WARRANTY ON ELECTRICAL EQUIPMENT OF SEWING MACHINE #

For two years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which

appear in the electrical end electronic equipment of the sewing machine, including motor, wiring, electronic components,

switch and speed control. #

FULL 90-DAY WARRANTY ON ALL PARTS AND MECHANICAL ADJUSTMENTS ÷

For 90 days from the date of purchase, Sears will, free of charge, replace any parts and provide mechanical service

_) necessary for proper operation of the sewing machine, except for normal maintenance. .._,

t WARRANTY SERVICE IS AVAILABLE BY RETURNING THE SEWING MACHINE TO THE

0 NEAREST SEARS SERVICE CENTER IN CANADA. #

If this machine is used for commercial or rental purposes, the above warranty coverage applies for only 90 days from the _,

date of purchase.

This warranty gives you specific legal rights. You may also have other rights which vary from province to province, t

-* SEARS CANADA INC., TORONTO, ONT., M5B 2B8

GARANTIA

GARANTIA COMPLETA POR 25 AI;IOS EN LA CABEZA DE LA MAQUINA DE COSER

Durante 25 a_os desde la fecha de la compra, Sears ofrece, libre de costo, reparar los defectos en material o de t

- manufacture que puedan presentarse en los componentes mec&nicos de la cabeza de la mdquina de coser.

GARANTIA COMPLETA POR 2 AI_IOS EN EL EQUIPO ELECTRICO DE LA MAQUINA DE COSER

Durante 2 a_os desde la fecha de la compra, Sears ofrece, libre de costo, reparar los defectos en material o de

; manufactura que puedan presentarse en el equipo el_ctrico de la m_quina de coser, incluyendo componentes

el_ctricos, motor, conexiones el_ctricas, interruptor y control de velocidad. _

GARANTIA COMPLETA POR 90 DIAS SOBRE TODAS LAS PARTES Y AJUSTES MECANICOS

Durante 90 d_as desde la fecha de la compra, Sears ofrece, libre de costo, reemplazar cualquiera parte y proveer el

servicio mecdnico necesario para la apropiada operaci6n de la m_quina de coser, excepto pare mantenimiento normal.

EL SERVICIO DE GARANTIA SE PUEDE OBTENER ENVIANDO LA MAQUINA DE COSER AL t

CENTRO/DEPARTAMENTO DE SERVICIOS SEARS MAS CERCANO EN CANADA. t

Siesta ma.quina de coser se utilize para propSsitos comerciales o de alquiler, la cobertura de garantia citada mas ardba

_) es v&lida _nicamente durante 90 dias a partir de la fecha de compra.

# Esta garant[a le da a usted derechos legales especfficos, pero usted puede tener tambi_n otros derechos los cuales

varian de provincia a provincia.

# SEARS CANADA INC., TORONTO, ONT., M5B 2B8

GARANTIE

GARANTIE TOTALE DE 25 ANS SUR LE MI_CANISME DE LA MACHINE

Pendant 25 ans, _ partir de la date d'achet, Sears r_parera gratuitement tout d_faut de mat_riau ou de fabrication qui

# appara?tra dans le m_canisme de votre machine.

GARANTIE TOTALE DE DEUX ANS SUR L'I_QUIPEMENT ELECTRIQUE

Pendant deux ans, _ partir de la date d'achat, Sears r_parsra gratuitement tout defaut de mat_riau ou de fabrication qui t

--" appara?tra dans le moteur, le ill, I'interrupteur ou la commande de vitesse de marche, et dans les circuits _lectriques.

GARANTIE TOTALE DE 90 JOURS SUR TOUTES LES PII_CES ET LA VISE AU POINT DU MECANISME

Pendant 90 jours, _ partir de la date d'achat, Sears fera gratuitement tout remplacement de pi_ce et r_glage n_cessaires

÷ au bon fonctionnement de la machine; rentretien ordinaire _tant _ la charge de I'utilisateur.

POUR B_NI_FICIER DES AVANTAGES QU'OFFRE LA GARANTIE CI-DESSUS, ADRESSEZ-VOUS A VOTRE t

# MAGASIN HABITUEL OU AU SERVICE APRt=S-VENTE SEARS, PARTOUT AUX CANADA.

Si cette machine &coudre sert _ des fins commerciales ou de location, la garantie ci-dessus ee limite & 90 jours _.

--" compter de la date d'achat.

Cette garantie vous donne des droits I_gaux precis, at _ventuellement d'autres droits, ceux-ci pouvant varier d'une ---"

-_ province & une eutre.

SEARS CANADA INC., TORONTO, ONT., M5B 2B8

Iv

Machine Specifications

Item

Sewing speed (Maximum):

Stitch length:

Stitch width:

Stitch package (Built-in):

Buttonhole:

Machine dimensions:

Weight (Net):

Specification

Over 730 s.p.m.

4 mm (Maximum)

6.5 mm (Maximum)

24 (Model 17624), 20 (Model 17620)

4 step built-in buttonhole & snap-in automatic BH (2 styles)

W 16.6"(422 mm )x D 6.8"(172 mm) x H 11.7"(297 mm )

18.5 Ibs (8.5kg)

Especificaciones de la mdquina

ArUculo

Velocidad de costura (M&xima):

Longitud de puntada:

Ancho de puntada:

NQmero de puntadas (Integradas):

Ojales:

Dimensiones de la m&quina:

Peso:

Especificacibn

M_.s de 730 s.p.m.

4 mm (M&xima)

6.5 mm (M_xima)

24 (Modelo 17624), 20(Modelo 17620)

Funci6n de ojal incorporado de 4 pasos y accesorio de ojal

autom&tico con 2 tipos

16.6"(422 mm ) de ancho x 6.8"(172 mm ) de profundidad x

11.7" (297 mm ) de altura

18.5 Ibs (8.5kg)

Caract6ristiques de la machine

Description

Vitesse de couture (Maximum):

Longueur du point:

Largeur du point:

Ensemble de points (Programm_s):

Boutonniere:

Dimensions de la machine:

Poids de la machine:

Caract6ristiques

730 points-minute

4 mm (Maximum)

6.5 mm (Maximum)

24 (Mod61e 17624), 20 (Mod61e 17620)

Boutonni6re int_gr6e en 4 6tapes et accessoire encliquetable

pour les boutonnieres en deux styles

Largeur: 16.6"(422 mm ) x Profondeur: 6.8"(172 mm ) x

Hauteur: 11.7" (297 mm )

18.5 Ib (8.5kg)

V

TABLE OF CONTENTS

I_V:1_VJl:[,.l[o)=1I_.,I=]uu_

Portable Case or Cabinet ............................... 2

Names of Parts ............................................... 2

Available Accessories and Attachments ........ 4

__] _1[.=Y_=][_

Connecting Machine to Power Supply ........... 6

For Your Safety ............................................... 6

Operating Instructions ;................................... 6

Controlling Sewing Speed .............................. 6

Pressure Adjusting Lever ................................ 8

Presser Foot Lifter .......................................... 8

Thread Cutter .................................................. 8

Extension Table .............................................. 8

Changing Needle .......................................... 10

To Remove and Attach the Foot Holder ....... 10

To Remove and Attach Presser Feet ............ 10

Presser Foot Types ....................................... 12

• A: Zigzag Foot ......................................... 12

• H: Straight Stitch Foot ............................. 12

• J: Sliding Buttonhole Foot ....................... 12

• E: Zipper Foot ...... i................................... 12

• F: Satin Stitch Foot .................................. 12

• Automatic Buttonhole Foot ...................... 14

• Quilter ....................................................... 14

Selecting Needle and Thread ....................... 16

Bobbin Winding ..................................... 20 - 24

• Horizontal Spool Pin ................................ 20

• Additional Spool Pin ................................ 20

• Bobbin Winding ....................................... 22

• Removing the Hook Cover Plate ............. 24

• Inserting the Bobbin ................................. 24

Threading the Machine ................................ 26

• Threading the Machine ............................ 26

• Drawing up Bobbin Thread ...................... 26

Adjust the Needle Thread Tension for Straight

Stitch ............................................................. 28

• Correct Tension ........................................ 28

• Tension is too tight ................................... 28

• Tension is too loose ................................. 28

Adjust the Needle Thread Tension for Zigzag

Stitch ............................................................. 30

• Correct Tension ........................................ 30

• Tension is too tight ................................... 30

• Tension is too loose ................................. 30

Stitch Selector .............................................. 32

Stitch Width Control ..................................... 34

Stitch Length Control ................................... 34

Adjusting Stretch Stitch Balance .................. 36

Reverse Stitch Control ................................. 36

I&_)]DI[,o,___:t_[,n,]=L'j[OII]_O,]_

Straight Stitch ............................................... 38

Use the Seam Guides ................................... 38

Turn a Square Corner ................................... 38

Use the Quilter Guide ................................... 38

Topstitching .................................................. 40

Quilting ......................................................... 40

Zipper Sewing ........................................ 42 - 44

To Raise or Drop the Feed Dogs .................. 46

Darning ......................................................... 46

Basic Zigzag ................................................. 48

Satin Stitch ................................................... 48

Monogramming ............................................ 50

Applique ........................................................ 50

Bar Tacking ................................................... 52

Embroidery ................................................... 52

Button Sewing .............................................. 54

Overcasting Stitch ........................................ 54

Blind Hem Stitch ........................................... 56

Lace Work ..................................................... 58

Multiple Zigzag Stitch ................................... 58

Shell Stitch .................................................... 60

Box Stitch ..................................................... 60

Fagoting Stitch ............................................. 62

Two-point Shell Stitch .................................. 62

Two-point Box Stitch .................................... 62

Overedge Stitch ............................................ 64

Decorative Stitch of Geometric Patterns ..... 64

Straight Stretch ............................................. 66

Rick-rack Stretch .......................................... 66

Overcast Stretch Stitching ........................... 68

Smocking ...................................................... 68

Serging .......................................................... 70

Elastic Stretch Stitch .................................... 70

Stretch Patching ........................................... 70

Herringbone Stretch ..................................... 72

Decorative Stretch Patterns ......................... 72

Manual Buttonhole ................................ 74 - 78

Automatic Buttonhole ............................ 80 - 86

Twin Needle Stitches (Optional Item) ........... 88

Replacing the Light Bulb .............................. 90

Cleaning the Bobbin Holder ......................... 90

Cleaning the Hook Race and Feed Dogs ..... 92

Oiling the Machine ........................................ 92

Troubleshooting ............................................ 94

¥!

Page is loading ...

I_r±__v_i_"Io_l I_

Portable Case or Cabinet

A full line of sewing machine cabinets and carrying

cases is available through the RSOS catalog at your

nearest Sears retail store.

Names of Parts

(_) Reverse stitch control

(_ Sewing guide display

(_ Stitch selector

(_ Stitch length setting display

(_ Stitch width setting display

(_ Stitch length control

(_ Stitch width control

(_ Bobbin winder spindle

(_ Spool pin

@ Upper thread guide

@ Thread take-up lever

@ Thread tension dial

@ Face cover

(_ Thread cutter

Needle plate

Hook cover plate

@ Hook cover plate release button

@ Extension table (Accessory box)

@ Carrying handle

Handwheel

@ Buttonhole pitch balance adjusting lever

@ Feed balancing dial

@ Power switch

Machine socket

Nomenclature plate

Drop feed lever

@ Free-arm

@ Presser foot lifter

Thumb screw

Presser foot

@ Needle clamp screw

@ Snap-on button

@ Foot control

[

o

2

Page is loading ...

Available Accessories and Attachments

All parts listed may be ordered from any Sears store or

service center.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

1. PART NUMBER

2. PART DESCRIPTION

3. MODEL NUMBER

4. NAME OF ITEM (SEWING MACHINE)

If the parts you need are not stocked locally, your order

will be electronically transmitted to a Sears Repair Parts

Distribution Center for expedited handling.

Ref. No. Part No. Description

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

3O

31

*102869107

102403202

650807008

*993001100

*993011100

*993011400

*993011600

*993011800

*826815000

625031500

823801015

685502019

822804118

829801002

825813016

820817015

*784805004

000009803

647808009

820832005

*741814003

802424004

822020503

822019509

213502003

213501116

213504005

213505006

213506007

213503015

*200002008

*200003009

*200005001

*200013105

*214872011

*941620000

200262101

802422002

10 x Bobbin

Spool pin fert

Assorted needle set

5 x No. 11 stretchfabric needle (BLU)

5 x No. 11 needle (ORG)

5 x No. 14 needle (RED)

5 x No. 16 needle (PUR)

5 x No. 18 needle (GRN)

Twin needle

Additional spool pin

H: Straight stitch foot

A: Zigzag foot

F: Satin stitch foot

E: Zipper foot

J: Sliding buttonhole foot

G: Blind hem foot

Needle threader

Light bulb

Seam ripper/Buttonhole opener

Large screw driver

Oil

Lint brush

Large spool holder

Small spool holder

Buttonhole guide plate

Buttonhole base plate

Template (Round end, small)

Template (Round end, large)

Template (Keyhole)

Buttonhole foot

Piping foot

Gathering foot

Pin-tuck foot

Hemmer foot (2 ram)

Walking foot

Ruffler

Needle threader

Quilter

* These items are not furnished with the machine, but

may be ordered per instructions above.

"1 2 3

5 6

%

7

%

9 10 11

13 14 15

17 18

21 22

19

23

*4

/

8

%

"12

"16

2O

*24

*25 *26 *27 *28

* 29 30 31

Page is loading ...

Connecting Machine to Power Supply

O Power supply plug

Outlet

Machine plug

Power switch

_) Machine socket

(_ Light bulb

Before connecting the power cord, make sure the

voltage and frequency shown on the machine

conform to your electrical power.

1. Turn off the power'switch (_.

2. Insert the machine plug _ into the machine

socket _.

3. Insert the power supply plug _ into the outlet _).

4. Turn the power switch _) to turn on the power

and sewing light (_.

For Your Safety

* While in operation, always keep your eye on the

sewing area. Do not touch any moving parts

such as the thread take-up lever, handwheel or

needle.

* Always turn off the power switch and unplug from

the power supply:

- When leaving the machine unattended.

- When attaching or removing any parts.

- When cleaning the machine.

* Do not place anything on the foot control, when

not sewing.

Operating instructions:

"For appliances with a polarized plug (one blade

wider than the other).

To reduce the risk of electric shock, this plug is

intended to fit in a polarized outlet only one way. If

it does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician to

install the power outlet. Do not modify the plug in

any way."

"Foot Controller Model YC-482J-1 or TJC-150 for

use with Sewing Machine Models 385.17624 and

385.17620"

J

Controlling Sewing Speed

Sewing speed can be varied by the foot control.

The harder you press on the foot control, the faster

the machine runs.

6

Page is loading ...

Pressure Adjusting Lever

Pressure adjusting lever

The pressure adjusting lever should be set at "3" for

regular sewing.

Reduce pressure to "2" for applique, cut work, draw

work and basting.

Set pressure at "1" when sewing chiffon, lace,

organdy and other fine fabrics. Velour and knits with

a lot of stretch may also require pressure at "1".

Presser Foot Lifter

Presser foot lifter

Normal up position

Highest position

The presser foot lifter raises and lowers your presser

foot.

You can raise it about 1/4" ( 0.6 cm ) higher than the

normal up position for easy removal of the presser

foot or to help you place heavy fabric under the foot.

Thread Cutter

Thread cutter

You do not need a pair of scissors to cut threads

after sewing. Just use the built-in thread cutter.

". _ ','

Extension Table

Detaching the table :

Pull the table away from the machine, as illustrated.

Attaching the table:

Push the extension table until it snaps into the

machine.

O Extension table

Projection

Hole

Accessory Box :

Open the cover of the accessory box toward you.

Sewing accessories are conveniently located in the box.

\

J

Page is loading ...

Changing Needle

(_ Needle clamp screw

(_ Pin

(_) Needle clamp

[] Turn off the power switch.

Raise the needle to its highest position by turning

the handwheel counterclockwise and lower the

presser foot.

Loosen the needle clamp screw (_ by turning it

counterclockwise.

Remove the needle from the clamp (_.

[] Insert a new needle into the needle clamp (_) with

the flat side to the rear.

When inserting the needle into the clamp (_),

push it up as far as it goes. Tighten the clamp

screw (_ firmly by turning it clockwise.

[] To check for a good needle, put the flat side of

the needle onto something flat (needle plate,

hook cover plate, glass, etc.)

The gap between the needle and the flat surface

should be consistent. Never use a bent or blunt

needle. A damaged needle can cause permanent

snags or runs in knits, fine silks and silk-like fabrics.

[] []

[]

To Remove and Attach the Foot Holder

C) Thumb screw

(_) Foot holder

_) Presser bar

[] To remove:

Remove the thumb screw (_ by turning it

counter-clockwise with a screwdriver.

[] To attach:

Match the hole in the foot holder _) with the

threaded hole in the presser bar _). Fit the

thumb screw (_) into the hole. Tighten the screw

(_ by turning it clockwise.

f

[] []

To Remove and Attach Presser Feet

(_ Red button

_) Groove

(_) Pin

[] To remove:

Raise the needle to its highest position by turning

the handwheel counter-clockwise.

Raise the presser foot, and press the red button

0 on the back of the foot holder.

[] To attach:

Place a selected presser foot so the pin (_) on

the foot lies just under the groove (Z) of the foot

holder.

Lower the presser bar to lock the foot in place.

f

[] []

10

i.

4------ _'__ .F_ --

Page is loading ...

Presser Foot Types

• Zigzag Foot ( Foot A )

Use this foot for both straight and zigzag stitching.

For: Basic zigzag (page 48)

Bar tacking (page 52)

Button sewing (page 54)

Overcasting stitch (page 54)

Blind hem stitch (page 56)

Lace work (page58)

Multiple zigzag stitch (page 58)

Box stitch (page 60)

Fagoting stitch (page 62)

Two-point shell stitch (page 62)

Two-point box stitch (page 62)

Overedge stitch (page 64)

Rick-rack stretch (page 66)

Overcast stretch stitching (page 68)

Smocking (page 68)

Elastic stretch stitch (page 70)

Stretch patching (page 70)

Herringbone stretch (page 72)

Decorative stretch patterns (page 72)

Twin needle stitches (page 88)

• Straight Stitch Foot ( Foot H )

Use this foot exclusively for straight stitching with

center needle position.

For: Straight stitch (page 38)

Topstitching (page 40)

Straight stretch (page 66)

= S|iding Buttonhole Foot ( Foot J )

Use this foot'for manual buttonhole making. It is

marked to help you measure a buttonhole

accurately.

For: Manual buttonhole (page 74)

Foot A: %

PleA:

Pied A:

Foot H:

Pie H:

Pied H:

Foot J: %

Pie J:

Pied J:

Foot E:

Pie E:

Pied E:

• Zipper Foot ( Foot E )

This foot can be set to sew on each side of the

zipper. The edges of the foot guide the zipper and

keep the seam straight.

For: Zipper sewing (page 42)

• Satin Stitch Foot ( Foot F )

Use this transparent foot for satin stitch and

outlining applique.

For: Darning (page 46)

Satin stitch (page 48)

Monogramming (page 50)

Applique (page 50)

Shell stitch (page 60)

Decorative stitch of geometric patterns (page 64)

Twin needle stitches (page 88)

Foot F: %

Pie F:

Pied F:

12

Page is loading ...

• Automatic Buttonhole Foot

Use this foot when making buttonholes with the

automatic buttonhole attachment.

For: Automatic buttonhole (page 80)

Buttonhole foot

Pie para ojdles

Pied & point boutonnieres

• Quilter

This attachment turns your zigzag foot into a quilting foot.

For: Straight stitching (page 38, 40).

Quilter

Guia de acolchado

Guide & matelasser

J

14

Page is loading ...

Selecting Needle and Thread

For general sewing use needle size 11 or 14. A fine thread and needle should be used for sewing lightweight

fabrics so the fabric will not be marred. Heavy fabrics require a needle large enough to pierce the fabric

without fraying the needle thread.

In the needle case there is one each of size 11, 14, 16, 18 and a blue needle. Use the blue needle to eliminate

skipped stitches when sewing knits and synthetic fabrics.

Special needles should be used on certain fabrics. A denim needle with a sharp tip effectively pierces dense

fabrics such as denim and canvas. For topstitching, a special topstitching needle with a larger eye accom-

modates heavier weight thread. Leather needles punch small holes in leather and suede allowing the thread

to follow through the hole.

Check your needles frequently for rough or blunt tips. Snags and runs in knits, fine silks and silk-like fabrics

are permanent and are often caused by damaged needles.

Always purchase good quality thread. It should be strong, smooth and consistent in thickness.

f

WEIGHT FABRIC TYPE OF NEEDLE NEEDLE SIZE

Very Light Chiffon, Georgette, Fine Lace, Organdy, Organdy Universal 9 (65)

Net, Tulle Ball Point 9 (65)

Batiste, Voile, Lawn, Pure Silk, Crepe de Chine, Orange 11 (75)

Sheer Crepe, Chambray, Handkerchief Linen, Blue 11 (75)

Gingham, Challis, Percale, Wool Crepe, Peau de

Light Sole, Taffeta, Satin, Silk Surah, Satin-backed 12 (80)

Crepe, Qiana

Blue 11 (75)

Single Knits, Jersey, Swimwear, Tricot Ball Point 11 (75)

Leather, Suede Wedge Point Leather 11 (75)

Flannel, Velour, Velvet, Muslin, Velveteen, Poplin,

Corduroy, Broadcloth, Linen, Chintz, Gabardine, Red 14 (90)

Felt, Terry, Burlap, Quilted Fabrics

Medium Double Knits, (synthetic and natural) Stretch

Velour,

Stretch Terry, Ball Point 14 (90)

Sweater Knits

Leather, Vinyl, Suede Wedge Point Leather 14 (90)

Denim, Sailcloth, Ticking Denim 16 (100)

Double Faced Wool, Heavy Coating, Fake Fur,

Heavy Drapery Fabrics Purple 16 (100)

Leather, Suede Wedge Point Leather 16 (100)

Canvas, Duck, Upholstery Fabrics Green 18 (110)

Topstitching for Special Finish Topstitching 11 (75)

14 (90)

J

16

Page is loading ...

Bobbin Winding

• Horizontal Spool Pin

(_) Spool pin

Large spool holder

(_ Small spool holder

Lift up the spool pin O. Place a spool of thread on

the spool pin with the thread coming off the spool as

shown.

Attach the large spool holder _, and press it firmly

against the spool of thread.

The small spool holder (_ is used with narrow or

small spools of thread.

• Additional Spool Pin

O Additional spool pin

Spool pin hole

_) Spool pin felt

The additional spool pin (_ is for bobbin winding

without unthreading the machine and for twin needle

sewing.

Insert the additional spool pin (_ in the hole _.

Place the felt _ and a spool on the pin.

20

Page is loading ...

• Bobbin Winding

@ For horizontal spool pin

® For additional spool pin

C) Pull the handwheel out to the right.

(_) Draw thread from the spool.

® Guide the thread around the thread guide.

_) Thread through the hole in the bobbin from the

inside to the outside.

® Put the bobbin on the bobbin winder spindle.

® Push the bobbin to the right.

(_ With free end of the thread held in your hand,

depress the foot control. Stop the machine

when it has made a few turns and cut the thread

close to the hole in the bobbin.

® Depress the foot control again. When the bobbin

is fully wound, it stops automatically. Return the

bobbin winder to its original position by moving

the spindle to the left and cut the thread as

shown.

@ Push the handwheel in. The machine will not

function until the clutch is engaged.

NOTE:

Position of the bobbin winder stopper is

adjustable for the required amount of

thread on the bobbin (example 1/2 full or

full etc.).

Use a screwdriver and loosen the screw

one turn or less so that you can adjust the

position of the bobbin winder stopper.

Do not take out the screw all the way.

®

33

®

J

22

Page is loading ...

• Removing the Hook Cover Plate

(_ Hook cover plate release button

Hook cover plate

Slide the hook cover plate release button (_ to the

right, and remove the cover plate _).

\

• Inserting the Bobbin

End of thread

Notch

Threading chart

[] Place a bobbin in the bobbin holder with the

thread running off counterclockwise.

[] Guide the thread into the notch (_ on the front

side of the bobbin holder. Draw the thread to the

left, sliding it between the tension spring blades.

[] Continue to draw the thread lightly until the

thread slips into the notch _. Pull out about 6"

(15 cm) of thread.

[] Attach the hook cover plate. Check the threading

by referring to the chart _ shown on the hook

cover plate.

f

[]

\

24

Page is loading ...

Threading the Machine

• Threading the Machine

* Raise the thread take-up lever to its highest

position by turning the handwheel

counterclockwise.

* Raise the presser foot lifter.

* Place a spool on the spool pin, with thread coming

off as shown.

(_ Draw the end of thread around the upper thread

guide.

(_ While holding the thread near the spool, draw the

end of the thread down around the check spring

holder.

(_ Firmly draw the thread up from right to left over

the take-up lever and down into the take-up lever

eye.

(_ Slide the thread behind the needle bar thread

guide on the left.

(_ Thread the needle from front to back or use a

needle threader.

We recommend using the convenient needle

threader(#200262101), included with your

machine.

I- l 1

• Drawing up Bobbin Thread

O Raise the presser foot. Hold the needle thread

lightly with your left hand and rotate handwheel

counterclockwise for one complete turn.

(_ Bring the bobbin thread up by pulling the needle

thread up.

Pull both threads under and to the back of the

presser foot, leaving 4 to 6" (10 to 15cm)

of thread clear.

-<

J

26

Page is loading ...

Adjust the Needle Thread Tension for Straight

Stitch

• Correct tension

(_) Needle thread (Topthread)

(_ Bobbin thread (Bottom thread)

(_ To loosen

(_) To tighten

The ideal straight stitch has threads locked between

two layers of fabric, as illustrated (magnified to show

detail).

If you look at the top and bottom of a seam, notice

that there are no gaps. Each stitch is smooth and

even.

When adjusting needle thread tension, the higher the

number, the tighter the top thread tension.

Results depend on;

stiffness and thickness of the fabric

number of fabric layers

type of stitch

• Tension is too tight

O Needle thread (Top thread)

Bobbin thread (Bottom thread)

(_ To loosen

Right side (Top side)

_) Wrong side (Bottom side)

The bobbin thread shows through on the right side

of the fabric and it feels bumpy, Turn the dial to a

lower tension setting number to loosen the needle

thread tension.

®

• Tension is too loose

(_ Needle thread (Top thread)

Bobbin thread (Bottom thread)

_) To tighten

The needle thread shows through on the wrong side

of the fabric and it feels bumpy. Turn the dial to a

higher tension setting number to tighten the needle

thread tension.

28

Page is loading ...

Adjust the Needle Thread Tension for Zigzag

Stitch

For an ideal zigzag stitch, bobbin thread does not

show on right side of fabric and needle thread shows

slightly on wrong side.

See the illustrations for correct appearance.

To match this appearance, adjust the needle tension.

• Correct tension

Right side of fabric (Top side of fabric)

Wrong side of fabric (Bottom side of fabric)

Minimize the amount of needle thread visible on the

wrong side of fabric without causing excessive

puckering or causing bobbin thread to show on the

right side of fabric.

Results vary with fabric, thread and sewing

conditions.

• Tension is too tight

(_) Right side of fabric (Topside of fabric)

Wrong side of fabric (Bottom side of fabric)

Corner of each zigzag pulls together on the right

side of fabric.

@ ®

• Tension is too loose

Q Right side of fabric (Top side of fabric)

Wrong side of fabric (Bottom side of fabric)

The needle thread loops through wrong side of fabric

and is pulled almost together.

@ ®

3O

Page is loading ...

Stitch Selector (how to select stitches)

Raise the needle to the highest position, and select a

pattern by turning the stitch selector.

The red mark will be shown on the selected stitch.

(Set the stitch length control at S.S. when using the

stretch stitch.)

* Window O shows stitch number, foot number and

stitch.

Stitch patterns are color-coded to a recommended

setting zone at the stitch length control.

ZONES:

Red: Straight, zigzag and utility stitches

Green: Geometric decorative stitches

Blue: Built-in buttonhole

Gold: Stretch stitches

(_ Red mark

(_ Stitch selector

0--1 --2--3=4----5_6.5

[_ WIDTH

T--O_=_I _2--3--4

STRETCH

FOOT

LENGTH

BH

2 3 4 5 6 7 8 91011121314

:?

c_ C> C3

17624

BH I 2 3 4 5 6 7 8 9101112

17620

32

Page is loading ...

Kenmore 385. 17624 User manual

This manual is also suitable for

Kenmore 385. 17624 User manual

in other languages

Related papers

Other documents