Lightolier 402MRIC9X User manual

Lightolier
Brand
Lightolier
Model
402MRIC9X
Type
User manual

Lightolier 402MRIC9X is a recessed downlight fixture designed for use with 4 3/4" (121mm) low voltage MR16 bulbs. It features an insulated ceiling housing for direct contact with thermal insulation and an internal thermal cut-out to prevent overheating. The mounting bars are rotatable and lockable, and the integral T-bar tabs eliminate the need for additional nailing. The junction box is CSA/UL certified for a maximum of 8 No. 12 ga. 90º C through branch circuit conductors and has easy access from both sides with snap-on covers.

Lightolier 402MRIC9X is a recessed downlight fixture designed for use with 4 3/4" (121mm) low voltage MR16 bulbs. It features an insulated ceiling housing for direct contact with thermal insulation and an internal thermal cut-out to prevent overheating. The mounting bars are rotatable and lockable, and the integral T-bar tabs eliminate the need for additional nailing. The junction box is CSA/UL certified for a maximum of 8 No. 12 ga. 90º C through branch circuit conductors and has easy access from both sides with snap-on covers.

03-03
4 3/4" (121mm) aperture Lytecaster
Low Voltage MR16 12V Recessed Downlight
IC Frame-In-Kit
Complete fixture consists of Reflector Trim & Frame-in Kit. Select each separately
POWER PACK CUT-OUT
402MRIC9X 4 3/4" (121mm)
Accepts all 4 3/4" (121mm) Low Voltage MR16 trims 400 series: see
Reflector Trim specification sheets.
Features Accessories
Mounting Frame : 20ga. galvanized steel. Four slots are positioned 90º Mounting Bars Extenders : 1964
apart to simplify alignment. 20" (508mm) long. Set of 2
Insulated Ceiling Housing : 26ga. galvanized steel. CSA certified and UL listed for
direct contact with thermal insulation.
Mounting Bar Locking Clips : 0098
Internal thermal cut-out : insures against overheating due to incorrect lamping.
To lock mounting bars in place after installation. Set of 12.
Mounting Bars: (4) 18 ga. galvanized steel. 13" (330mm) long bars extend to
27" (686mm), rotatable and lockable, integral T-bar tabs. Spike detail
Vapor Barrier Extender : VBE300
eliminates the need of additional nailing. Polyvinyl Air Vapour Barrier ; to comply with provincial legislation. For all
Mounting Bars Locking Clip : (1) locks mounting bars in place.
non Air-Seal frame-In-Kits.
Socket : Porcelain body ; Two-pin (GX5.3 base) Pre-wired with 18 ga. Teflon
250º leads to junction box.
Transformer : 75VA Magnetic, 120 volt primary, nominal 12 volt secondary,
class "H".
Junction Box : 4"(102mm) x 3"(76mm) x 2"(51mm) 18 ga. galvanized steel .
CSA/UL certified for maximum of 8 No. 12 ga. 90º C through branch circuit
conductors. Integral cable clamp permit attachment of non metallic Loomex
Labels : CSA , UL
without need of additional connectors. Pry-out knock-outs accept BX cable.
Easy access from both sides with snap-on covers. Damp or Wet location rated depending on trim used.
WE RESERVE THE RIGHT TO CHANGE DETAILS OF DESIGN, MATERIALS AND FINISH, IN ANY WAY
THAT WILL NOT ALTER INSTALLED APPEARANCE OR REDUCE FUNCTION AND PERFORMANCE.
Lightolier CFI, 3015 Louis Amos Lachine, (Quebec) H8T 1C4
REFLECTOR TRIM
402MRIC9X
  • Page 1 1

Lightolier 402MRIC9X User manual

Lightolier
Brand
Lightolier
Model
402MRIC9X
Type
User manual

Lightolier 402MRIC9X is a recessed downlight fixture designed for use with 4 3/4" (121mm) low voltage MR16 bulbs. It features an insulated ceiling housing for direct contact with thermal insulation and an internal thermal cut-out to prevent overheating. The mounting bars are rotatable and lockable, and the integral T-bar tabs eliminate the need for additional nailing. The junction box is CSA/UL certified for a maximum of 8 No. 12 ga. 90º C through branch circuit conductors and has easy access from both sides with snap-on covers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents