Lightolier 302MRIC7X User manual

Category
Work lights
Type
User manual

This manual is also suitable for

Lightolier LyteCaster 302MRIC7X is a recessed downlight MR16 IC Frame-In-Kit with a 3 3/4" (95mm) aperture. It's a complete fixture consisting of Reflector Trim & Frame-in Kit. The power pack has a cut-out of 3 3/4" (95mm). The mounting frame is made of 20ga. galvanized steel, with four slots positioned 90º apart to simplify alignment. The insulated ceiling housing is made of .018" galvanized steel and is CSA certified for direct contact with thermal insulation. The mounting bars are made of 18 ga. galvanized steel, and are 13" (330mm) long, extending to 27" (686mm).

Lightolier LyteCaster 302MRIC7X is a recessed downlight MR16 IC Frame-In-Kit with a 3 3/4" (95mm) aperture. It's a complete fixture consisting of Reflector Trim & Frame-in Kit. The power pack has a cut-out of 3 3/4" (95mm). The mounting frame is made of 20ga. galvanized steel, with four slots positioned 90º apart to simplify alignment. The insulated ceiling housing is made of .018" galvanized steel and is CSA certified for direct contact with thermal insulation. The mounting bars are made of 18 ga. galvanized steel, and are 13" (330mm) long, extending to 27" (686mm).

Rev: 02
3 3/4" (95mm) aperture Lytecaster
Low Voltage 50W MR16 / 37W MR16 IR 12V Recessed Downlight
MR16 IC Frame-In-Kit
Complete fixture consists of Reflector Trim & Frame-in Kit. Select each separately
POWER PACK CUT-OUT
302MRIC7X 3 3/4" (95mm) Accepts few 3 3/4" (95mm) 300 serie trims ; see Reflector
Trim specification sheets.
Features Accessories
Mounting Frame: 20ga. galvanized steel. Four slots are positioned 90º Mounting Bars Extenders : 1964
apart to simplify alignment. 20" (508mm) long. Set of 2
Insulated ceiling Housing: .018" galvanized steel. CSA certified
for direct contact with thermal insulation. Internal thermal cut-out insures against
Mounting Bar Locking Clips : 0098
overheating due to incorrect lamping. To lock mounting bars in place after installation. Set of 12.
Mounting Bars: (4) 18 ga. galvanized steel. 13" (330mm) long bars extend to
27" (686mm), rotatable and lockable, integral T-bar tabs. Spike detail
Vapor Barrier Extender : VBE
eliminates the need of additional nailing. Polyvinyl Air Vapour Barrier ; to comply with provincial legislation. For all
Mounting Bars Locking Clip: (1) locks mounting bars in place. Additional
non Air-Seal frame-In-Kits.
clips are sold separately (0098 set of 12)
Socket : Porcelain body ; Two-pin (GX5.3 base) Pre-wired with 18 ga. Teflon
250º leads to junction box.
Dimming
Transformer: Magnetic 50VA, 120 volts primary, nominal 12 volts secondary,
class "H". (integral thermal protector)
Dimming controls: use only dimmers specifically designed for use with
Junction Box: 4"(102mm) x 3"(76mm) x 2"(51mm) 18 ga. galvanized steel .
transformers, like Lightolier Onset, Sunrise series LV or VA dimmers, or any
CSA/UL certified for maximum of 4 No. 12 ga. 90º C through branch circuit Lightolier Controls dimming system. Low voltage fixtures may produce audible
conductors. Integral cable clamp permit attachment of non metallic Loomex noise. Attention should be given for noise sensitive applications.
without need of additional connectors. Pry-out knock-outs accept BX cable.
Easy access from both sides with snap-on covers.
Lamp cover: Aluminum heat deflector for 50W MR16 / 37W MR16 IR or
ES/ESD16 dichroic lamps.
Labels : CSA , UL
Damp or Wet location rated depending on trim used.
WE RESERVE THE RIGHT TO CHANGE DETAILS OF DESIGN, MATERIALS AND FINISH, IN ANY WAY
THAT WILL NOT ALTER INSTALLED APPEARANCE OR REDUCE FUNCTION AND PERFORMANCE.
Lightolier CFI, 3015 Louis Amos Lachine, (Quebec) H8T 1C4
REFLECTOR TRIM
302MRIC7X
  • Page 1 1

Lightolier 302MRIC7X User manual

Category
Work lights
Type
User manual
This manual is also suitable for

Lightolier LyteCaster 302MRIC7X is a recessed downlight MR16 IC Frame-In-Kit with a 3 3/4" (95mm) aperture. It's a complete fixture consisting of Reflector Trim & Frame-in Kit. The power pack has a cut-out of 3 3/4" (95mm). The mounting frame is made of 20ga. galvanized steel, with four slots positioned 90º apart to simplify alignment. The insulated ceiling housing is made of .018" galvanized steel and is CSA certified for direct contact with thermal insulation. The mounting bars are made of 18 ga. galvanized steel, and are 13" (330mm) long, extending to 27" (686mm).

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI