SUITABLE LOCATIONS
The Threesome has been designed especially for cavity type ceilings. Flat roof installation is
NOT recommended.
Threesome must not be mounted in areas subject to direct splashing. Threesome must
be mounted in the horizontal position only. Unsuitable for ‘cathedral’ or ‘raked’ ceilings.
Threesome comes with 4 Infra-red Heat Globes which emit harmless radiant heat.
Threesome is best positioned directly above the area requiring warmth. Before you start,
make sure your ceiling has at least 280mm clearance from the roof (see diagram 2).
WHERE TO LOCATE
Radiant globe heaters are not designed to heat entire rooms. They provide instant,
concentrated heat to persons standing directly below the heat lamps. Therefore, units should
be located over the area where drying off takes place, not directly over a shower
or bath.
These heaters are not designed to be left on for extended periods of time, as this could
cause overheating and premature failure. Threesome units, even those without fans, should
not be covered or installed in situations which restrict the natural ventilation of the units for
cooling purposes.
Ceiling insulation should be kept well clear of the units (at least 100mm). For optimum
performance, models with exhaust fans should be installed in areas with good ventilation,
to enable fresh air to ow into the room. It is recommended that there is at least a 500mm
clearance above the unit, and that the ceiling space is adequately ventilated to allow
appropriate air ow through the unit. Any restrictions on return air entering the room, or
exhausted air escaping from the ceiling space, will impair effectiveness and may contribute to
premature failure.
RADIANT HEAT
Threesome requires no warm up period because of its efcient, Radiant Heat Globes. Heat
is directed at you for an instant warmth you can feel, rather than gradually warming the entire
room. Because of this, Threesome only needs to be turned ON when you are in the room.
MOUNTING
1. Using this card in its open state as a template, position it
in the area you want your Threesome and draw around
the edges with a pencil to mark the hole cutting size.
BE SURE TO CHECK ABOVE THE CEILING FOR
MINIMUM SPACE OF 280mm (for optimum performance
allow 500mm or more clearance) AND THE LOCATION
OF THE CEILING JOISTS. Ensure there is a minimum
of 100mm clear space between the Threesome unit and
any ceiling insulation.
2. Use a saw to cut the section along the drawn lines.
3. The lamp surround easily unclips from the main body
by lifting gently from any side. Remove it and the 4 heat
globes to avoid damage from knocks and vibrations.
Now insert your Threesome with both side springs pulled
inwards so that the body can pass through the hole
without damaging the plaster. Return springs to original
position to x body securely to the ceiling.
NOTE: Springs are adjusted to suit either 10mm or 13mm
plasterboard ceiling.
4. Clip the lamp surround back onto the body making sure
both clips snap into place. Fit retaining spring as shown
in diagram.
5. The lamp surround has been shaped to position heat
globes correctly in the main body. Screw the four, large
heat globes through the lamp surround holes, tightening
rmly to ensure a good electrical contact. DO NOT
FORCE OR OVER-TIGHTEN. Screw centre light globe
into place. Centre lampholder is designed to accept 100
Watt (max), reector type, R80, screw in light globes.
IMPORTANT SAFEGUARDS
• The Threesome is not intended for use by young children or inrm persons without supervision
.
• Young children should be supervised to ensure that they do not play with the appliance.
• Ensure that the switch is in the off position when changing the heat lamp (globe) or light globe.
• Ensure that the wattage of a replacement globe is the same as the globes supplied with the unit.
• Ensure the grille is free of objects, dust build up, etc. Make sure that the air ow through the
grille is not inhibited.
ELECTRICIANS’ WIRING INSTRUCTIONS
Your Threesome requires a 230/240 Volt, 50Hz electrical supply. All electrical work must
be carried out by a qualied electrician and installed in accordance with relevant Electrical
Wiring Regulations.
Your new Threesome comes with all required switches and mounting plate.
WIRING DETAILS
1. Decide the best position for the switch set and mount it. Be sure to click the switches into
the backing plate in the desired order beforehand.
2. Connect wiring to switches as shown in the appropriate electrical diagram.
3.
Remove screws from
terminal cover on the
Threesome and put aside.
Wire according to the
label beside the terminal
strip. Once the wires
are connected incoming
cable must not be fouled
by cover. Use appropriate
knockouts in terminal
cover to accommodate
cable before replacing.
Screw down rmly.
TEST
Clean surround and globes with a soft, moist cloth. Check power is switched on and all
switches activate properly, according to their marked function.
CLEANING
• Ensure the Threesome is switched off before cleaning.
• Remove globes when they are at room temperature. Wipe with a damp cloth, never immerse.
• Unclip lamp surround and wash in warm, soapy water. Always use a soft cloth, never abrasives.
•
Clean away any excess uff from the inside of the body, motor blade brackets.
PERMANENT
APPLIANCE
WIRING
E
NEUTRAL
HEAT
FAN
HEAT
LIGHT
SWITCHES EARTH
ACTIVE