Before installing your All Pond Solutions PP ensure you have read the
instructions and taken note of all safety advice. If you have any further
questions or concerns please contact the retailer before installing the
PP system.
The pump comes complete with a generous supply of 3 core cable,
however, should any additional cable be required then the use of an
approved waterproof cable connector is essential.
The power supply must be earthed and fused at 3amps.
Regularly inspect the cable for damage and deterioration
Always use a residual circuit device (RCD) for additional safety
For permanent installation to the mains supply, it is necessary to comply
with the regulations of the Local Electricity Authority.
Consult a qualified electrician if in doubt about any aspects of wiring.
Important: Disconnect the mains electricity supply before attempting
any installation/maintenance or handling of any kind.
Only run your PP fully submerged.
The PP should never be run dry as this will cause the unit to overheat
and cause permanent damage.
Do not attempt to modify this unit in any way and only use the
recommended parts for replacement.
All connections must be earthed.
Do not connect to any voltage other than that stated on the pump.
Do not place in liquids other than water
Do not use in water above 90°F or 30°C
INSTRUCTIONS
ELECTRIC
SAFETY
H(m)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
8000
6800
5800
5000
3800
2000
0
LITRES PER HOUR
9000
7800
7000
5600
4800
4000
3200
2000
0
SPECIFICATION
MODEL
POWER CONSUMPTION(W)
MAX FLOW RATE (L/h)
MAX HEIGHT (m)
DISCHARGE CONECTION
VOLTAGE (V)
FILTER SURFACE
WEIGHT(kg) 10m CABLE
AC230V/50Hz
470
3.3
10000
8500
7600
6800
5400
4600
4000
3400
2800
1800
10000PP9000PP
70
8000
3.2
8000PP
95
9000
3.6
AC230V/50Hz
470
3.3
155
10000
5
AC230V/50Hz
470
3.5
POND AND AQUARIUMPOND AND AQUARIUM
WATER PUMPWATER PUMP
INSTRUCTION MANUALINSTRUCTION MANUAL
8000PP8000PP 9000PP9000PP
10000PP10000PP
50%
MORE ENERGY
EFFICIENT
50%
EFFICIENT
MORE ENERGY
// //
Before installing your All Pond Solutions PP ensure you have read the
instructions and taken note of all safety advice. If you have any further
questions or concerns please contact the retailer before installing the
PP system.
The pump comes complete with a generous supply of 3 core cable,
however, should any additional cable be required then the use of an
approved waterproof cable connector is essential.
The power supply must be earthed and fused at 3amps.
Regularly inspect the cable for damage and deterioration
Always use a residual circuit device (RCD) for additional safety
For permanent installation to the mains supply, it is necessary to comply
with the regulations of the Local Electricity Authority.
Consult a qualified electrician if in doubt about any aspects of wiring.
Important: Disconnect the mains electricity supply before attempting
any installation/maintenance or handling of any kind.
Only run your PP fully submerged.
The PP should never be run dry as this will cause the unit to overheat
and cause permanent damage.
Do not attempt to modify this unit in any way and only use the
recommended parts for replacement.
All connections must be earthed.
Do not connect to any voltage other than that stated on the pump.
Do not place in liquids other than water
Do not use in water above 90°F or 30°C
INSTRUCTIONS
ELECTRIC
SAFETY
H(m)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
8000
6800
5800
5000
3800
2000
0
LITRES PER HOUR
9000
7800
7000
5600
4800
4000
3200
2000
0
SPECIFICATION
MODEL
POWER CONSUMPTION(W)
MAX FLOW RATE (L/h)
MAX HEIGHT (m)
DISCHARGE CONECTION
VOLTAGE (V)
FILTER SURFACE
WEIGHT(kg) 10m CABLE
AC230V/50Hz
470
3.3
10000
8500
7600
6800
5400
4600
4000
3400
2800
1800
10000PP9000PP
70
8000
3.2
8000PP
95
9000
3.6
AC230V/50Hz
470
3.3
155
10000
5
AC230V/50Hz
470
3.5
INSTRUCTIONS
Before installing your All Pond Solutions PP ensure you have read the
instructions and taken note of all safety advice. If you have any further
questions or concerns please contact the retailer before installing the
PP system.
ELECTRIC
The pump comes complete with a generous supply of 3 core cable,
however, should any additional cable be required then the use of an
approved waterproof cable connector is essential.
The power supply must be earthed and fused at 3amps.
Regularly inspect the cable for damage and deterioration
Always use a residual circuit device (RCD) for additional safety
For permanent installation to the mains supply, it is necessary to comply
with the regulations of the Local Electricity Authority.
Consult a qualified electrician if in doubt about any aspects of wiring.
SAFETY
Important: Disconnect the mains electricity supply before attempting
any installation/maintenance or handling of any kind.
Only run your PP fully submerged.
The PP should never be run dry as this will cause the unit to overheat
and cause permanent damage.
Do not attempt to modify this unit in any way and only use the
recommended parts for replacement.
All connections must be earthed.
Do not connect to any voltage other than that stated on the pump.
Do not place in liquids other than water
Do not use in water above 90°F or 30°C
H(m)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
8000
6800
5800
5000
3800
2000
0
LITRES PER HOUR
9000
7800
7000
5600
4800
4000
3200
2000
0
10000
8500
7600
6800
5400
4600
4000
3400
2800
1800
SPECIFICATION
10000PPMODEL
POWER CONSUMPTION(W)
9000PP
70
8000
3.2
8000PP
MAX FLOW RATE (L/h)
MAX HEIGHT (m)
DISCHARGE CONECTION
VOLTAGE (V)
FILTER SURFACE
WEIGHT(kg) 10m CABLE
AC230V/50Hz
470
3.3
95
9000
3.6
AC230V/50Hz
470
3.3
155
10000
5
AC230V/50Hz
470
3.5
Before installing your All Pond Solutions PP ensure you have read the
instructions and taken note of all safety advice. If you have any further
questions or concerns please contact the retailer before installing the
PP system.
The pump comes complete with a generous supply of 3 core cable,
however, should any additional cable be required then the use of an
approved waterproof cable connector is essential.
The power supply must be earthed and fused at 3amps.
Regularly inspect the cable for damage and deterioration
Always use a residual circuit device (RCD) for additional safety
For permanent installation to the mains supply, it is necessary to comply
with the regulations of the Local Electricity Authority.
Consult a qualified electrician if in doubt about any aspects of wiring.
Important: Disconnect the mains electricity supply before attempting
any installation/maintenance or handling of any kind.
Only run your PP fully submerged.
The PP should never be run dry as this will cause the unit to overheat
and cause permanent damage.
Do not attempt to modify this unit in any way and only use the
recommended parts for replacement.
All connections must be earthed.
Do not connect to any voltage other than that stated on the pump.
Do not place in liquids other than water
Do not use in water above 90°F or 30°C
INSTRUCTIONS
ELECTRIC
SAFETY
H(m)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
8000
6800
5800
5000
3800
2000
0
LITRES PER HOUR
9000
7800
7000
5600
4800
4000
3200
2000
0
SPECIFICATION
MODEL
POWER CONSUMPTION(W)
MAX FLOW RATE (L/h)
MAX HEIGHT (m)
DISCHARGE CONECTION
VOLTAGE (V)
FILTER SURFACE
WEIGHT(kg) 10m CABLE
AC230V/50Hz
470
3.3
10000
8500
7600
6800
5400
4600
4000
3400
2800
1800
10000PP9000PP
70
8000
3.2
8000PP
95
9000
3.6
AC230V/50Hz
470
3.3
155
10000
5
AC230V/50Hz
470
3.5
WARRANTY INFORMATION
Your PP comes complete with a 12 months warranty that covers all
electrical parts.
If you require support with the operation of your PP, require parts or if your
PP develops a fault during the warranty period please contact the supplier
of your PP system.
Please be aware that spare parts are not covered by the warranty and a
charge is applied for replacements.
Always disconnect the mains electricity supply before attempting any
installation or handling of any kind.
Never run the pump out of water or without the pre-filter housing
attached, as this will damage the pump.
Do not attempt to pull the out of the water by it’s electrical supply cable.
Regularly inspect the pump and cable for any signs of damage.
REGULAR MAINTENANCE
www.allpondsolutions.co.uk
MAINTENANCE
At regular intervals dependant on individual water conditions it will be
necessary to carry out the following maintenance program.
Important: Disconnect the mains electricity supply before attempting
any maintenance work.
OPERATION
When installing your PP connect your outlet pipe using a clamp/bracket
and ensure this is tight and secure.
Place your PP in the water and ensure it is fully submerged. The PP
must rest on a horizontal surface.
Connect your outlet pipe to either your filter, water feature or alternative
location. Ensure this is fixed in place.
Power on your PP system.
/
