Lotus Maximus EVO Series Operating instructions

Brand: Lotus

Model: Maximus EVO Series

Type: Operating instructions

LOTUS Maximus EVO

Pump Instructions

ELECTRICAL CONNECTIONS

NEUTRAL = BLUE N

EARTH = GREEN & YELLOW

LIVE = BROWN L

The pump comes complete with 10 mtrs of 3 core cable, however, should any additional cable be

required then the use of an approved waterproof cable connector is essential.

l The power supply must be protected by a residue circuit device (RCD), earthed and fused at 3

amps.

l Regularly inspect the cable for damage and deterioration

l For permanent installation to the mains supply, it is necessary to comply with the regulations

of the Local Electricity Authority.

l Consult a qualified electrician if in doubt about any aspects of wiring.

SAFETY

l You must disconnect the mains electricity supply before attempting any installation/maintenance or

handling of any kind.

l The pump should never be run dry as this will cause the unit to overheat and damage it.

l Do not attempt to modify this unit in any way and only use the recommended parts for replacement.

l Do not place in liquids other than water.

l All connections must be Earthed.

l Do not connect to any voltage other than that stated on the pump.

l Do not use in water above 90°f / 30°C.

INSTALLATION

The pump should be sited on a firm base, raised from the bottom of the pond. Connect a suitable length

and diameter of hose pipe. If using the optional Air Mix system, ensure the air line is attached to the front

of the rotor housing leading through the front of the cage, and the other end is secured out of the water

allowing air to be drawn in.

Please Keep Instructions

for Future Reference.

Figure 1.

Release retaining Catch

by lifting part ‘A’.

Figure 2.

Pull pump cage apart as shown in diagram

and remove pump - Please note notch for

cable in cage for relocating the cable during

re-assembly.

Make sure Catch ‘A’ is not pushed all the

way to the top as this will interfere with the

opening and closing of the cage.

Retaining catch

‘A’

Figure 3.

Twist the rotor housing 1/4 turn

anticlockwise to access rotor.

Remove rotor for cleaning or

inspection.

Please clean

if dirty or

replace if

damaged.

Rotor Housing

Air Mix Inlet

Optional Air

Mix Airline

Downloaded from www.watergardeningdirect.com

Guarantee

Your Maximus Evo pump is guaranteed against failure due to defective workmanship

or material for a period of 3 years from the date of purchase. Failure caused by

accidental damage, misuse, neglect or used in liquids other than cold water are

excluded from this guarantee. If a failure occurs during this period, a purchase receipt

must be returned with the unit which will be repaired or replaced. The company can

not accept any additional claims or consequential losses.

THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS.

THIS UNIT IS MADE IN THE E.C AND CONFORMS TO CE REGULATIONS

www.lotuswgp.com Made in Italy [email protected]

Dealers Stamp:

At regular intervals dependant on individual water conditions it will be necessary to carry out the

following maintenance program.

Pull pump cage apart as shown in figure 2. and remove pump - Please note notch for cable in cage for

relocating the cable during re-assembly.

Twist the rotor housing 1/4 turn anticlockwise to access rotor.

Important:- Disconnect the mains electricity supply before attempting any maintenance work.

Maintenance and cleaning (see fig 1, 2 & 3 overleaf).

1. Follow these safety instructions. Make sure that the pump is disconnected from the mains supply.

2. Release the retaining catch situated under the handle of the pump.

6. Remove the rotor from motor housing.

7. Clean all parts using water and soft sponge.

8. Once cleaned, reassemble the pump and place back into the cage. Make sure the cable is inserted in the

cutout notch before closing the cage and reattach the catch ‘A’. Ensure the pump is submerged before

switching on.

REGULAR MAINTENANCE

l You must disconnect the mains electricity supply before attempting any installation or handling of any

kind.

l Never run the pump out of water or without the outer casing attached, as this will damage the pump.

l Do not attempt to pull the pump out of the water by it’s electrical supply cable.

l Regularly inspect the pump and cable for any signs of damage.

POINTS TO REMEMBER

Disposal of your old product Your product is designed and manufactured with high quality material and

components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a

product, it means the product is covered by the European Directive 2002/976/EC. Please contact your local

authority about correct disposal for electrical and electronic equipment.

Please act according to your local rules and do not dispose of your old products with your normal household

waste. The correct disposal of your old product will help prevent potential negative consequences for the

environment and human health.

Spare parts for Maximus EVO

800

1500

2500

4000

6000

Spare Parts

Rotor

MER800

MER1500

MER2500

MER4000

MER6000

Fountain Kits - (Waterbell and Daisy)

MEF800

MEF1500

MEF2500

MEF4000

MEF6000

O-Rings

MEO1500

MEO2500

MEO4000

MEO6000

Downloaded from www.watergardeningdirect.com

Twist top of jet to

adjust Dome/Bell

fountain.

Push jets onto

extending riser pipe.

Extend riser pipe

to desired

fountain height.

Knurled markings on

fountain riser pipe.

Push riser pipe into

‘T’ Piece & Flow Adjuster.

Push fountain assembly into

the top of the pump.

Nb. Please ensure that

the fountain assembly is

assembled in this way, taking

into account that the knurled

markings are placed at the

bottom please see the diagram (left).

Only one end of the riser pipe assembly

is adjustable.

Twist ‘T’ Piece and Flow

Adjuster to increase or

decrease flow to side

outlet.

Maximus Evo 800 Fountain Assembly Instructions

Dome

Fountain

Bell

Fountain

Interchangeable Heads:

Simply unscrew the fitted

head and re-install the

desired option.

21 Hole

1 Stage Jet

33 Hole

2 Stage Jet

Optional jets supplied

can be used instead

of the dome or bell jets

Fountain jet

control valve

Screw into the top

of the pump’s outlet

Side outlet

control valve

‘T’ piece &

flow adjuster

Interchangeable

Fountain Jet Option

Adjustable

fountain top

Top removable

for cleaning

Maximus Evo 1500 - 6000

Fountain Assembly

Downloaded from www.watergardeningdirect.com

Lotus Maximus EVO Series Operating instructions

Lotus Maximus EVO Series Operating instructions

Lotus Maximus EVO Series Operating instructions

Related papers

Other documents