Seeed reServer Industrial J3011- Fanless AI-enabled NVR Server Assembly Guide

Brand: Seeed

Model: reServer Industrial J3011- Fanless AI-enabled NVR Server

Type: Assembly Guide

This manual is also suitable for

Seeed reServer Industrial J3011- Fanless AI-enabled NVR Server is a versatile and powerful device designed for a wide range of applications, including video surveillance, edge computing, and industrial automation.

With its compact design and fanless operation, the Seeed reServer Industrial J3011 is ideal for deployments in space-constrained and harsh environments. The device is powered by a NXP i.MX 8M Plus processor, which provides high performance and low power consumption.

The Seeed reServer Industrial J3011 comes with a variety of features that make it a great choice for video surveillance applications. It supports up to four SATA hard drives or SSDs, providing ample storage capacity for video recordings. The device also includes a built-in AI engine that can be used for object detection and recognition, enabling advanced video analytics capabilities.

reServer Industrial

SATA HDD/SSD Installation Guide

Assembly Guide

Step 1

Loosen these two screws.

Note: the LoRaWAN®/4G/5G/Series Wireless modules and 2.5" SATA HDD/SSD used in the following installation instructions are not included in the device

and are optional.

Remove the panel.

Remove the two screws and slowly pull the Drive Bays out.

Install/remove these 4 screws.

Push the drive bays inside along the bracket tracks slowly.

Lock the drive bays with screws.

Install the panel, making sure that the protrusions of the panel line up

with the grooves on the bottom of the device.

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

1 2 3 4 5 6 7 8

120°-KM3.0 x L5.0 PM3.0 x L7.0 PM2.5 x L4.0 PM3.0 x L4.0 Stud-M3 x 6.5+M2 x 2.0 CM2.0 x L3.0 CM3.0 x L6.0 Stud-M3 x 16.0+4.0

Lock with two screws.

HDD/SSD optional

4*Screw-120°-KM3.0x5.0

2*Screw-120°-KM3.0x5.0

Assembly Guide

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step 11

Step 12

Step 13

Step 14

Step 15

Step 16

Remove the six screws from the bottom.

1 x6

If you need to install a LoRaWAN® module, insert the LoRaWAN® module

into the Mini PCIe interface (lower interface) and lock it with two screws. If

you need to install a 4G/5G module, insert the 4G/5G module into the M.2

Key B interface (upper interface) and lock it with one screw. Please note that

only one module can be installed at a time on these two interfaces.

4 x1

6 x2

Mini PCIE

(Module optional)

5G/4G

(Module optional)

4 x1

6 x2

Mini PCIE

(Module optional)

5G/4G

(Module optional)

If you need to replace the SSD, remove the screw, and gently

remove the SSD module.

3 x1

1 x4

6 x1

3 x2

7 x8

8 x2

2 x8

1 x4

Install the TPM module in the correct orientation.

6 x1

(Module optional)

2 x8

Lock them with six screws.

1 x6

This step is only necessary if you need to remove the carrier board.

Remove the two SATA data and power cables and

remove the 4 screws on both sides.

1 x4

Seeed reServer Industrial J3011- Fanless AI-enabled NVR Server Assembly Guide

Brand: Seeed

Model: reServer Industrial J3011- Fanless AI-enabled NVR Server

Type: Assembly Guide

This manual is also suitable for

Download PDF

report

Seeed reServer Industrial J3011- Fanless AI-enabled NVR Server Assembly Guide

This manual is also suitable for

Seeed reServer Industrial J3011- Fanless AI-enabled NVR Server Assembly Guide

Related papers

Other documents