Apollo 65 Series Installation guide

Category
Fire protection
Type
Installation guide
© Copyright Apollo Fire Detectors Limited 2006
Apollo Fire Detectors Limited, 36 Brookside Road, Havant, Hants, PO9 1JR, UK
Tel +44 (0)23 9249 2412 Fax +44 (0)23 9249 2754
Email: techsales@apollo- re.co.uk Website: www.apollo- re.co.uk
4
1
Series 65 Sounder Base
Installation Guide
General
This guide describes the installation of the following sounder
Part number Product Description
45681-512 Series 65 Sounder Base
45681-513 Series 65 Sounder Base with diode
The Series 65 Sounder Base is a high-ef ciency conventional alarm sounder incorporating a
base for the Apollo Series 65 and 60 ranges of detectors. The product offers 32 tones which are
shown in the table on pages 3 and 4.
Mounting and Location
The sounder base can be secured to a conduit box or surface mounted. Sounder Bases should
be located to ensure correct operation of the detector in accordance with the detector
manufacturer’s recommendations and local regulations or codes of practice.
Note: The sounder is classi ed as a Type A device according to EN54-3, ie, is suitable for indoor
use only.
Wiring
The sounder base is designed so that separate detector and sounder circuits can be con-
nected. The sounder circuit is connected using the PCB mounted 4-way terminal block (Fig. 1).
The detector circuit is connected using the terminals marked L1IN, L1OUT and L2 around the rim
of the base in the same way as a standard detector base (Figs 1&2).
Two separate earth terminals are provided to allow the screen termination of earth conduc-
tors to maintain continuity between cables that contain an earth conductor. As this product
is designed for use on conventional systems with separate detector and sounder circuits, the
earths should not be connected together.
PP2272/Issue 1
FIRE DETECTORS LIMITED
From control panel
EARTH
L2
L1 IN
–R
L1OUT
EARTH
L2
L1 IN
–R
L1OUT
EARTH
L2
L1 IN
–R
L1OUT
End-of-line
device
Remote LED
+
T
T
on
one T
ab
able
TONE TONE T
YPE
YPE TONE D
ES
ES
CR
CRIPTION
/
/
AP
APPLICATION
DIL
SW
SWITCH
1_2
1_2_
3_4
3_4_5
SO
UND
UND L
EV
EVEL
(d
BA
BA @ 1m)
A
VE
VERAG
E
E
CU
CURRENT (mA)
17
750
750Hz I-O-O-O-O 86 6
18
2400
2400Hz I-O-O-O-I 86 4.8
19
750
750Hz 0.33s ON/0.51s OFF I-O-O-I-O 86 3
20
750
750Hz
0.51s ON/0.33s OFF I-O-O-I-I 86 4.3
21
800
800Hz
0.2s ON/0.2s OFF I-O-I-O-O 86 2.6
22
510
510Hz
,
, 0.5s/
610
610Hz, 0.5s I-O-I-O-I 91 5.8
23
550
550Hz
,
, 0.33s/
100
1000Hz
,
, 0.7s I-O-I-I-O 91 5.3
24
250
250Hz – 1
200
200Hz @ 12Hz I-O-I-I-I 87 3.8
25
500
500Hz – 1
200
200Hz @ 0.33Hz. I-I-O-O-O 92 5.1
26
2500
2500Hz –
285
2850Hz @ 7Hz. I-I-O-O-I 94 4.8
27
600
600Hz – 9
00
00Hz
/
/ 0.9s I-I-O-I-O 90 5.5
28
660
660Hz – 6
80
80Hz
/
/ 0.9s I-I-O-I-I 85 4.5
29 6
70
70Hz – 7
25
25Hz
/
/ 0.9s I-I-I-O-O 84 4.2
30
920
920Hz – 7
50
50Hz
/
/ 0.9s I-I-I-O-I 93 6.1
31
700
700Hz -
900
900Hz, 0.3s/0.6s OFF I-I-I-I-O 90 4.6
32
900
900Hz -
760
760Hz, 0.6s/0.3s OFF I-I-I-I-I 91 4
Fig 1 Detector circuit wiring diagram
2
3
Tone Selection and Volume Control
The tone is selected using the 5 way DIL switch on the PCB. Refer to the table opposite for
details of the available tones and the switch settings required to select them.
The sound output of the unit can be reduced by adjusting the potentiometer on the PCB.
Stand-alone installation
The Series 65 Sounder Base can be used as a stand-alone device without a detector. For this
purpose caps are available which are tted instead of the detector.
Part number Product Description
45681-294 White cap
45681-295 Red cap
Technical Data
Operating voltage 17–60V DC
Current consumption 7mA
Volume at 1m 95±3dB(A)
Operating temperature –10° to +55°C
EARTH 1
EARTH 2
–R
L1 IN
L1 OUT
L2
© Apollo Fire Detectors Limited 2006/JDR
Volume control
DIL switch
SNDER – SNDER +
SOUNDER –
SOUNDER +
Fig 2 Series 65 Sounder Base Wiring
T
T one T able
TONE TONE T
YPE
YPE TONE D
ES
ESCRIPTION/
AP
APPLICATION
DIL
SW
SWITCH
1_2_3_4_5
SOUND L
EV
EVEL
(d
BA
BA @ 1m)
A
VE
VERAG
E
E
CURRENT (mA)
1 970Hz (BS5839-1:2002) O-O-O-O-O 91 5
2 800Hz/970Hz @ 2Hz (
BS
BS5839-1:2002) O-O-O-O-I 91 5.2
3 800Hz – 970Hz @ 1Hz (
BS
BS5839-1:2002) O-O-O-I-O 95 5
4
970Hz 1s OFF/1s ON
(Apollo Fire Detectors Alert Tone, BS5839-1:2002)
O-O-O-I-I 91 3
5
970Hz, 0.5s/ 630Hz, 0.5s
(Apollo Fire Detectors
Evacuate
Evacuate
Tone, BS5839-1:2002)
O-O-I-O-O 91 4.2
6
554Hz, 0.1s/ 440Hz, 0.4s
(France - AFNOR NF S 32 001 )
O-O-I-O-I 91 7
7
500 - 1200Hz, 3.5s/ 0.5s OFF
(Netherlands – NEN 2575:2000)
O-O-I-I-O 93 4.2
8
420Hz 0.625s ON/0.625s OFF
(Australia
AS
AS2220 Alert tone)
O-O-I-I-I 84 2.7
9
500 - 1200Hz, 3.75s/ 0.25s OFF
(Australia
AS
AS2220 Evacuation tone)
O-I-O-O-O 90 2
10 550Hz/440Hz @ 0.5Hz O-I-O-O-I 91 5.1
11
970Hz, 0.5s ON/0.5s OFF x 3/ 1.5s OFF
(ISO 8201 Low tone)
O-I-O-I-O 91 2.6
12
2850Hz, 0.5s ON/0.5s OFF x 3/1.5s OFF
(ISO 8201 High tone)
O-I-O-I-I 91 2.2
13
1200Hz – 500Hz @ 1Hz
(DIN 33 404)
O-I-I-O-O 93 3.5
14 400Hz O-I-I-O-I 85 4.2
15 550Hz, 0.7s/1000Hz, 0.33s (‘SafeSound’) O-I-I-I-O 90 5.5
16 1500Hz - 2700Hz @ 3Hz (Vandal Alarm) O-I-I-I-I 88 3.4
See overleaf for tones 17–32
  • Page 1 1
  • Page 2 2

Apollo 65 Series Installation guide

Category
Fire protection
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI