Airlink101 AEN-U35SE Quick Installation Manual

Airlink101
Brand
Airlink101
Model
AEN-U35SE
Category
HDD/SSD enclosures
Type
Quick Installation Manual

Airlink101 AEN-U35SE is a 3.5" USB2.0 SATA/IDE HDD Enclosure. It allows you to connect a 3.5" SATA or IDE hard drive to your computer via a USB 2.0 port. This can be useful for transferring data between your computer and hard drive, or for using the hard drive as an external storage device. The enclosure comes with a power adapter, USB 2.0 cable, screwdriver, and screw set.

Airlink101 AEN-U35SE is a 3.5" USB2.0 SATA/IDE HDD Enclosure. It allows you to connect a 3.5" SATA or IDE hard drive to your computer via a USB 2.0 port. This can be useful for transferring data between your computer and hard drive, or for using the hard drive as an external storage device. The enclosure comes with a power adapter, USB 2.0 cable, screwdriver, and screw set.

Quick Installation Guide
3.5” USB2.0 SATA/IDE HDD Enclosure
Model # AEN-U35SE
Hard Drive Installation
Step 1 Use the provided screwdriver to remove the two top screws on the left
side of the enclosure.
Section 1
Ver. 1A
Package Contents:
• 3.5” SATA/IDE Enclosure
with Stand
• Power adapter
• USB 2.0 Cable
• Quick Installation Guide
• Screwdriver and screw se
t
Step 2 Remove the two bottom screws from the right side of the enclosure.
Step 3 Hold the front and back of the enclosure and pull the two ends away
from each other. The two halves of the enclosure should slide apart exposing
the connectors.
Step 4 Make sure the hard drive you are installing is set to "Master" (refer to
the jumper setting information printed on your hard drive).
Step 5 Attach the connectors to your hard drive.
For IDE hard drives, attach the IDE connectors as shown below:
For SATA hard drives, attach the SATA connectors as shown below:
Note: Connect both the IDE and SATA power connectors will damage your
hard drive.
Step 6 Fasten the hard drive to the bottom of the enclosure with the provided
screws.
Step 7 Line up the two halves of the case.
Step 8 Push the two ends together. The enclosure should slide shut.
Step 9 Replace the four screws that were removed in steps 1 and 2.
Step 10 Connect one end of the power cord to the back of the enclosure and
connect the other end to a power outlet. Then connect one end of the USB
cable to the enclosure and the other end to your computer. Turn the power
switch to the ON position. The new drive is ready to use and you can find it
under “My Computer”.
Congratulations! The hard drive installation is complete.
Technical Support
E-mail: support@airlink101.com
Toll Free: 1-888-746-3238
Website: www.airlink101.com
* Specifications are subject to change without notice. Photos of the product may not reflect the
actual content.
Copyright ©2007 AirLink101® All rights reserved. AirLink101, the stylized AirLink101 logo, specific
product designations, and all other words and logos that are identified as trademarks and/or service
marks are, unless noted otherwise, the trademarks and service marks of AirLink101. All other
product or service names are the property of their respective holders. AirLink101 products are
protected under numerous U.S. and foreign patents and pending applications, mask work rights,
and copyrights.
Section 2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Airlink101 AEN-U35SE Quick Installation Manual

Airlink101
Brand
Airlink101
Model
AEN-U35SE
Category
HDD/SSD enclosures
Type
Quick Installation Manual

Airlink101 AEN-U35SE is a 3.5" USB2.0 SATA/IDE HDD Enclosure. It allows you to connect a 3.5" SATA or IDE hard drive to your computer via a USB 2.0 port. This can be useful for transferring data between your computer and hard drive, or for using the hard drive as an external storage device. The enclosure comes with a power adapter, USB 2.0 cable, screwdriver, and screw set.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents