Chicago Electric 38648 Set Up And Operating Instructions Manual

Brand: Chicago Electric

Model: 38648

Category: Power tools

Type: Set Up And Operating Instructions Manual

Chicago Electric 38648 Biscuit Joiner is a versatile tool that enables precise and efficient joining of wood pieces. It features a 120V motor with a no-load speed of 10,000 RPM, providing ample power for smooth cutting. The 4" diameter blade is mounted on a bearing spindle, ensuring stability and accuracy during operation. The biscuit joiner offers adjustable fence angles up to 45 degrees, allowing for angled cuts as needed. Additionally, it comes with preset depth stops at 0, 10, and 20 degrees, making it easy to achieve consistent joint depths.

BISCUIT JOINER

38648

SET UP AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2001 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Cover Revised 09c

SKU 38648 For technical questions, please call 1-800-444-3353. Page 2

SPECIFICATIONS

Motor Speed 10,000 RPM (No Load)

Power Rating 120 V~ / 60 Hz / 6 A

Blade 4” Diameter

Spindle Bearing Mounted

Fence Adjustment Max. Depth: 1-1/8”

Max. Angle: 45°

Preset Depth Stops 0, 10, 20

Power Cord 18 AWG, 3-Prong Plug

SAVE THIS MANUAL

You will need the manual for the safe-

ty warnings and precautions, assembly

instructions, operating and maintenance

procedures, parts list and diagram. Keep

your invoice with this manual. Write the

invoice number on the inside of the front

cover. Keep the manual and invoice in a

safe and dry place for future reference.

GENERAL SAFETY

WARNINGS AND

PRECAUTIONS

KEEP WORK AREA CLEAN AND 1.

DRY. Cluttered, damp or wet work

areas invite injuries.

KEEP CHILDREN AWAY FROM 2.

WORK AREA. Do not allow children

to handle this product.

STORE IDLE EQUIPMENT. 3. When

not in use, tools and equipment

should be stored in a dry location to

inhibit rust. Always lock up tools and

equipment and keep out of reach of

children.

DO NOT USE THIS PRODUCT IF 4.

UNDER THE INFLUENCE OF AL-

COHOL OR DRUGS. Read warning

labels on prescriptions to determine if

your judgment or reexes are im-

paired while taking drugs. If there is

any doubt, do not attempt to use this

product.

USE EYE, HEARING, AND 5.

BREATHING PROTECTION. Wear

ANSI-approved safety impact eye

glasses, ANSI approved hearing

protection, and dust mask or respira-

tor when using this product. ANSI-

approved safety impact eye glasses,

hearing protection, and dust masks

and respirators are available from

Harbor Freight Tools.

DRESS SAFELY. 6. Non-skid footwear

or safety shoes should be used when

working with this product. Do not

wear loose clothing or jewelry as they

can become caught in moving parts.

Wear a protective hair covering to

prevent long hair from becoming

caught in moving parts. If wearing

a long-sleeve shirt, roll sleeves up

above elbows.

INDUSTRIAL APPLICATIONS MUST 7.

FOLLOW OSHA REQUIREMENTS.

DO NOT OVERREACH. 8. Keep prop-

er footing and balance at all times to

prevent tripping, falling, back injury,

etcetera.

STAY ALERT. 9. Watch what you are

doing at all times. Use common

sense. Do not use this product when

you are tired or distracted from the

job at hand.

CHECK FOR DAMAGED PARTS. 10.

Before using this product, carefully

check that it will operate properly and

perform its intended function. Check

for damaged parts and any other

conditions that may affect the opera-

tion of this product. Replace or repair

damaged or worn parts immediately.

SKU 38648 For technical questions, please call 1-800-444-3353. Page 3

REPLACEMENT PARTS AND AC-11.

CESSORIES. When servicing, use

only identical replacement parts.

Only use accessories intended for

use with this product. Approved ac-

cessories are available from Harbor

Freight Tools.

MAINTAIN THIS PRODUCT WITH 12.

CARE. Keep this tool clean and

dry, and keep saw blades clean and

sharp for better and safer perfor-

mance.

MAINTENANCE: 13. For your safety,

service and maintenance should be

performed regularly by a qualied

technician.

USE THE RIGHT PRODUCT FOR 14.

THE RIGHT JOB. There are certain

applications for which this product

was designed. Do not use small

equipment, tools or attachments to

do the work of larger industrial equip-

ment, tools or attachments. Do not

use this product for a purpose for

which it was not intended.

SPECIFIC PRODUCT WARNINGS

AND PRECAUTIONS

GROUND THIS PRODUCT. 1. The

electrical power cord for this tool is

equipped with a grounded 3-prong

plug. Never remove the grounding

prong or modify the plug in any way.

Do not use adapter plugs with this

product. When in use, make sure

this product is always plugged into a

grounded 3-hole electrical receptacle

with an appropriate breaker switch

in-line.

MAKE SURE THE POWER SWITCH 2.

IS IN THE “OFF” POSITION BE-

FORE PLUGGING IN THE POWER

CORD.

DO NOT ABUSE THE POWER 3.

CORD. Do not use the cord to pull

the 3-prong plug from a power outlet.

Keep cord away from heat, oil, sharp

edges, and moving parts. Replace

damaged cord immediately. Route

the power cord safely. Protect it from

being damaged by other equipment

in the shop. Do not route the cord

where it can be walked on or tripped

over.

RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’

50’

75’

100’

150’

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A

* Based on limiting the line

voltage drop to ve volts at

150% of the rated amperes.

IF YOU USE AN EXTENSION 4.

CORD, MAKE SURE TO USE ONLY

UL APPROVED CORDS HAV-

ING THE CORRECT GAUGE AND

LENGTH.

(SEE TABLE A.)

MAINTAIN A SAFE WORK ENVI-5.

RONMENT. Do not use this tool in

or near damp or wet areas. Do not

expose this tool to rain. Keep work

area well lit. Make sure there is ad-

equate surrounding work space. Use

SKU 38648 For technical questions, please call 1-800-444-3353. Page 4

this product in a well ventilated area.

Do not operate this product in the

presence of ammable liquids, gases,

or dust. To avoid accidental electric

shock, do not let your body come in

contact with grounded surfaces such

as pipes, radiators, ranges and refrig-

erators.

DO NOT FORCE THE EQUIPMENT. 6.

This tool will do the work better and

safer at the speed and capacity for

which it was designed.

KEEP ALL GUARDS IN PLACE 7.

AND IN WORKING ORDER.

REMOVE ALL ADJUSTING 8.

WRENCHES FROM THE TOOL BE-

FORE TURNING ON THE BISCUIT

JOINER.

MAKE SURE THAT WHEN IN-9.

STALLING THE CUTTING BLADE

(61) THE SAW TEETH POINT TO-

WARD THE RIGHT SIDE OF THE

BISCUIT JOINER. (See FIGURE E

in OPERATION section.)

AVOID UNINTENTIONAL START-10.

ING. Make sure you are prepared to

begin work before turning the START

switch on.

DO NOT USE THIS TOOL FOR 11.

CUTTING METALS OR BRITTLE

MATERIALS. Do not cut dangerous

materials, such as asbestos which

can cause harmful dust or vapors.

Some woods contain preservatives 12.

such as copper chromium arsenate

(CCA) which can be toxic. When

cutting these materials, extra care

should be taken to avoid inhalation

and minimize skin contact.

BEFORE USING THE BISCUIT 13.

JOINER, MAKE SURE THE CUT-

TING BLADE IS PROPERLY

MOUNTED ON THE BLADE SPIN-

DLE. Make sure the Cutting Blade

(61) is balanced, securely mounted

and is not bent or cracked.

ALLOW THE CUTTING BLADE TO 14.

SPIN UP TO FULL SPEED BEFORE

FEEDING WOOD INTO IT. When

turning it off, allow the Cutting Blade

(61) to spin down and stop on its

own. Do not press against the saw

blade to stop it.

DO NOT FORCE THE CUTTING 15.

BLADE INTO THE MATERIAL BE-

ING CUT. Apply moderate pressure,

allowing the Cutting Blade (61) to cut

without being forced.

NEVER ATTEMPT TO REMOVE 16.

MATERIAL STUCK IN THE MOVING

PARTS OF THE BISCUIT JOINER

WHILE IT IS PLUGGED IN AND

RUNNING.

THE CUTTING BLADE WILL BE-17.

COME HOT WHILE CUTTING.

Allow the Cutting Blade (61) to com-

pletely stop and cool before touching.

WHENEVER POSSIBLE, USE 18.

CLAMPS OR OTHER SAFE, PRAC-

TICAL WAYS TO HOLD AND SUP-

PORT THE WORKPIECE.

ALWAYS DISCONNECT TOOL 19.

FROM ITS ELECTRICAL SUPPLY

SOURCE WHEN NOT IN USE OR

BEFORE PERFORMING ANY SER-

VICES OR MAINTENANCE such as

leaving the work area, moving the

tool from one location to another,

changing the saw blade, cleaning

sawdust from the unit, etcetera.

SKU 38648 For technical questions, please call 1-800-444-3353. Page 5

People with pacemakers should 20.

consult their physician(s) before use.

Electromagnetic elds in close prox-

imity to heart pacemaker could cause

pacemaker interference or pacemak-

er failure. In addition, people with

pacemakers should:

• Avoid operating alone.

• Do not use with power switch locked

on.

• Properly maintain and inspect to

avoid electrical shock.

• Any power cord must be properly

grounded. Ground Fault Circuit Inter-

rupter (GFCI) should also be imple-

mented – it prevents sustained elec-

trical shock.

WARNING: Some dust created by 21.

power sanding, sawing, grinding, drill-

ing, and other construction activities,

contains chemicals known [to the

State of California] to cause cancer,

birth defects or other reproductive

harm. Some examples of these

chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and ce-

ment or other masonry products

• Arsenic and chromium from chemi-

cally treated lumber

Your risk from these exposures var-

ies, depending on how often you do

this type of work. To reduce your

exposure to these chemicals: work in

a well ventilated area, and work with

approved safety equipment, such as

those dust masks that are specially

designed to lter out microscopic

particles. (California Health & Safety

Code § 25249.5, et seq.)

WARNING: Handling the cord on 22.

this product will expose you to lead,

a chemical known to the State of

California to cause cancer, and birth

defects or other reproductive harm.

Wash hands after handling. (Califor-

nia Health & Safety Code § 25249.5,

et seq.)

The warnings, precautions, and in-23.

structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

Vibration Safety

This tool vibrates during use. Re-

peated or long-term exposure to

vibration may cause temporary or

permanent physical injury, particularly

to the hands, arms and shoulders. To

reduce the risk of vibration-related

injury:

Anyone using vibrating tools regu-1.

larly or for an extended period should

rst be examined by a doctor and

then have regular medical check-

ups to ensure medical problems are

not being caused or worsened from

use. Pregnant women or people

who have impaired blood circulation

to the hand, past hand injuries, ner-

vous system disorders, diabetes, or

Raynaud’s Disease should not use

this tool. If you feel any symptoms

related to vibration (such as tingling,

numbness, and white or blue ngers),

seek medical advice as soon as pos-

sible.

Do not smoke during use. Nico-2.

tine reduces the blood supply to the

hands and ngers, increasing the risk

of vibration-related injury.

REV 09c

SKU 38648 For technical questions, please call 1-800-444-3353. Page 6

Wear suitable gloves to reduce the 3.

vibration effects on the user.

Use tools with the lowest vibration 4.

when there is a choice.

Include vibration-free periods each 5.

day of work.

Grip tool as lightly as possible (while 6.

still keeping safe control of it). Let

the tool do the work.

To reduce vibration, maintain the tool 7.

as explained in this manual. If any

abnormal vibration occurs, stop use

immediately.

SAVE THESE

INSTRUCTIONS.

REV 09c

SKU 38648 For technical questions, please call 1-800-444-3353. Page 7

UNPACKING

When unpacking, make sure the

product is intact and undamaged. If any

parts are missing or broken, please call

Harbor Freight Tools at 1-800-444-3353 as

soon as possible.

OPERATING INSTRUCTIONS

NOTE: All parts below refer to the parts

listed and shown in the parts list and

diagram near the end of this manual.

To Attach The Dust Bag:

FIGURE B

1. Insert the Dust Bag Adapter (75) into

the small opening of the Dust Bag

(45). Then, slide the Dust Bag Adapt-

er onto the Dust Porthole located at

the rear of the Joiner until it snaps

into place. (See Figure B.)

To remove the Dust Bag (45), pull the 2.

release tab located on the right side

of the Dust Porthole and slide the

Dust Bag off.

To empty the Dust Bag (45), hold the 3.

Dust Bag over a trash can and slide

the plastic clip off the end of the Bag

Clamp (63).

NOTE: For efcient dust pickup, empty the

Dust Bag (45) frequently.

To Attach The Adjustable Fence:

Remove both Allen Screws (67) on

the front of the Joiner Base (43), us-

ing the Hex Wrench provided. Slide

the Adjustable Fence (64) backward

onto the Joiner Base and secure the

Adjustable Fence with the two Allen

Screws.

(See Figures C and D.)

To Attach The Spacer:

Turn the Biscuit Joiner upside down.

Simply push the 2 Spacers (60) into

the holes in the bottom of the Biscuit

Joiner; one Spacer ts across the

front and the other Spacer ts across

the back (see Assembly Diagram).

To Set The Depth Stops:

Figure C

The biscuit joiner has 3 settings for

rapid adjustment to size 0, 10, or

20 biscuits. The Preset Depth Ad-

justment Dial (48) is located on the

adjusting screw at the rear of the

base plate, and has 3 pair of notches

marked 0, 10, and 20. An arrow is

molded into the base to the left of

the dial at the 9 o’clock position.

The number next to the arrow is the

selected biscuit size. To change the

setting, pull the dial out, the rotate it

to the desired size. (See Figure C)

Rev 02e

SKU 38648 For technical questions, please call 1-800-444-3353. Page 8

Adjusting Cutter Depth

The jointer should be pre-set at the factory

for the included biscuits. The depth of the

cut should be one half the width of the bis-

cuits you are using. If further adjustment

is necessary, proceed as follows.

Note: Any change made will affect all 3

preset positions.

Unplug the Joiner.1.

Position the preset dial to the biscuit 2.

size you are adjusting.

Turn the joiner upside down, bracing 3.

the handle against a solid surface.

Grasp the front of the base plate, and 4.

pull rearward until it stops.

Rotate the exposed blade so that one 5.

carbide tip is at maximum travel from

the face of the base plate.

Figure D

6. Use a small scale to measure this

distance, then turn Depth Adjustment

Dial (48) adjusting screw as needed.

The amount of exposed cutter should

be one half of the biscuit width.

(See Figure D.)

To Change The Cutting Blade:

Unplug the Joiner.1.

FIGURE E

FIGURE F

2. Turn the Biscuit Joiner upside down

and remove both Allen Screws (67)

on the Adjustable Fence (64), using

the Hex Wrench provided. Remove

the Adjustable Fence by sliding it for-

ward. (See Figures E and F.)

Rev 02e

SKU 38648 For technical questions, please call 1-800-444-3353. Page 9

FIGURE G

3. Place a Crescent Wrench on the

Spindle (1) and rmly hold to prevent

the Spindle from rotating. (See Fig-

ure G.)

Place the Arbor Wrench (included 4.

accessory) on the Blade Bolt (62) and

loosen counterclockwise to remove

the Blade Bolt. (See Figure G)

Note: Be aware of the sharp blade; handle

with care.

Slide the Cutting Blade (61) out, not-5.

ing the direction of the Blade Teeth.

Install the new Cutting Blade (61) 6.

onto the Spindle (1), making sure

the Blade Teeth are facing toward

the right of the Biscuit Joiner. (See

Figure F.)

Note: Be aware of the sharp blade; handle

with care.

Replace the Blade Bolt (62) and 7.

tighten clockwise until secure.

Reassemble the Adjustable Fence 8.

(64) to the Joiner Base (43) using the

two Allen Screws (67).

To Use The Locking On/Off Switch:

NOTE: The Biscuit Joiner Switch (35) is

located under the Hold Covers (28,

29). The orange Switch Lock Button

on the left side of the Cover locks the

Switch in the “ON” position for long

cutting operations.

(See Assy. Drawing.)

To turn the Biscuit Joiner on without 1.

locking it in the “ON” position, press

and hold the Switch (35) in. When

pressure is released, the Switch

snaps back to the “OFF” position.

To lock the Switch (35) in the “ON” 2.

position, press and hold the Switch

in. Then, press in the orange Switch

Lock Button on the left Hold Cover

(28).

To unlock the Switch (35) from the 3.

“ON” position, press and release the

orange Switch Lock Button.

Rev 02e

SKU 38648 For technical questions, please call 1-800-444-3353. Page 10

To Mark Slot Locations For Standard

Cuts:

FIGURE I

1. Always begin with the Joiner Base

(43) cutting into the end of the wood,

rather than the side. (See Figures H

and I.)

Mark the center of the slot at a point 2.

at least 2-1/2” from the outer edge of

the board.

NOTE: Allow at least 1” between slots in

multiple plate applications for best

results. Mark all slots on both boards

at the same time to assure proper

alignment.

Align the center line on the Adjustable 3.

Fence (64) with the pencil mark on

the wood. (See Figures B and C.)

Hold the Biscuit Joiner rmly with 4.

both hands. Turn the power “ON”

and push the Biscuit Joiner forward

slowly and smoothly.

When the Joiner Base (43) has butt-5.

ed completely against the wood sur-

face to be cut, pull the Biscuit Joiner

back and turn the power “OFF”.

To Mark Slot Locations For Other Types

Of Cuts:

NOTE: When making preparations for

cutting slots for T-butt, miter, edge-to-

edge, leg and rail, and square pattern

joints, there are two important steps

to ensure proper alignment of the

joints:

Align all boards as you want them to a.

appear when nished, then mark the

center line for the slots on all boards

at the same time.

Set the plate depth b. before making

the cuts.

Rev 02e

FIGURE H

SKU 38648 For technical questions, please call 1-800-444-3353. Page 11

CLEANING, INSPECTION,

AND MAINTENANCE

CAUTION: Always disconnect the Biscuit

Joiner from its electrical power supply

source before performing any clean-

ing, inspection, or maintenance.

Do not introduce water into the elec-1.

tric motor through the motor vents.

Do not use solvents to wipe off the 2.

Biscuit Joiner, as damage may result.

With a brush or soft cloth, remove all 3.

the sawdust from the Biscuit Joiner.

If necessary, wipe with a damp cloth. 4.

You may use a mild detergent.

Once clean, lubricate all moving parts 5.

with a light oil.

When storing, keep the Biscuit Joiner 6.

in a box, or cover with a cloth cover.

Before each use, inspect the general 7.

condition of the Biscuit Joiner. In-

spect switch, power plug and cord as-

sembly, and extension cord (if used)

for damage. Check for loose screws,

misalignment, binding of moving

parts, improper mounting, broken

parts, loose or damage Cutting Blade

and any other condition that may af-

fect its safe operation. If abnormal

noise or vibration occurs, turn off the

Biscuit Joiner immediately and have

the problem corrected before further

use.

Do not use damaged equipment.

Included in the Biscuit Joiner kit are 8.

two additional Motor Carbon Brushes

(23). In the event the old Carbon

Brushes need replacing, it is recom-

mended that only a qualied techni-

cian perform this service.

PLEASE READ THE FOLLOWING

CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR

HAS PROVIDED THE PARTS DIAGRAM IN THIS

MANUAL AS A REFERENCE TOOL ONLY. NEI-

THER THE MANUFACTURER NOR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY

OF ANY KIND TO THE BUYER THAT HE OR SHE

IS QUALIFIED TO MAKE ANY REPAIRS TO THE

PRODUCT OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN

FACT, THE MANUFACTURER AND/OR DISTRIBU-

TOR EXPRESSLY STATES THAT ALL REPAIRS

AND PARTS REPLACEMENTS SHOULD BE UN-

DERTAKEN BY CERTIFIED AND LICENSED TECH-

NICIANS AND NOT BY THE BUYER. THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT

OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO,

OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

SKU 38648 For technical questions, please call 1-800-444-3353. Page 12

PARTS LIST

Rev 02e

Part Description

Qty

1 Spindle 1

2 Straight Key 4 x 12 1

3 Circlips for Hole 1

4 Ball Bearing 80101 1

5 Screw M4 x 14 4

6 Washer M4 8

7 Packing Gland 1

8 Plate 2

9 Gear 1

10 Spindle Ring 1

11 Spindle Sleeve 1

12 Tapping Screw 4

13 Gear Cover 1

14 Nut M6 1

15 Washer M6 1

16 Pinion 1

17 Ball Bearing 80100 1

18 Clamp 1

19 Armature Assembly 1

20 Ball Bearing 80018 1

21 Hoop 1

22 Stator Assembly 1

23 Carbon Brush 2

24 Spring 2

25 Brush Hold Assembly 1

26 Rubber Gauge Washer 1

27 Housing Assembly 1

28 Hold Cover 1

29 Hold Cover 1

30 Tapping Screw 2

31 Washer M4 8

32 Wire Assembly 2

33 Name Plate 1

34 Tapping Screw 4

35 Switch 1

36 Cord Armor 1

37 Cord Clip 1

Part Description

Qty

38 Tapping Screw 2

39 Cord Assembly 1

40 Spring 1

41 Lock Pin 1

42 Washer 1

43 Joiner 1

45 Dust Bag 1

46 Depth Adjust. Screw 1

47 Spring 1

48 Depth Adjusting Dial (preset) 1

49 Square Nut 1

51 Bolt M6 4

52 Washer M6 2

53 Top Handle 1

54 Allen Screw M10 2

60 Spacer 2

61 Cutting Blade 1

62 Blade Bolt 1

63 Bag Clamp 1

64 Adjustable Fence 1

65 L-shaped Guide 2

66 Mounting Brackets 2

67 Allen Screw M5 2

68 Washer M5 2

69 Nut M5 4

70 Nut M6 2

75 Dustbag Adapter 1

ACCESSORIES

Assorted Biscuits: 0, 10, 20 gauge•

Carbon motor brush set•

4 mm Hex wrench•

Arbor wrench•

Glue bottle•

SKU 38648 For technical questions, please call 1-800-444-3353. Page 13

Note: Some parts are

listed and shown

for illustration

purposes only, and

are not available

individually as re-

placement parts.

ASSEMBLY DIAGRAM

SKU 38648 For technical questions, please call 1-800-444-3353. Page 14

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that this prod-

uct is free from defects in materials and workmanship for the period of 90 days from

the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,

criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental,

contingent, special or consequential damages arising from the use of our product. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-

LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection veries the defect, we will ei-

ther repair or replace the product at our election or we may elect to refund the purchase

price if we cannot readily and quickly provide you with a replacement. We will return re-

paired products at our expense, but if we determine there is no defect, or that the defect

resulted from causes not within the scope of our warranty, then you must bear the cost

of returning the product.

This warranty gives you specic legal rights and you may also have other rights

which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

REV 09c

Chicago Electric 38648 Set Up And Operating Instructions Manual

Brand: Chicago Electric

Model: 38648

Category: Power tools

Type: Set Up And Operating Instructions Manual

Download PDF

report

Chicago Electric 38648 Set Up And Operating Instructions Manual

Chicago Electric 38648 Set Up And Operating Instructions Manual

Related papers

Other documents