Chicago Electric 65533 Operating Instructions Manual
- Category
- Power tools
- Type
- Operating Instructions Manual
CAR VACUUM CLEANER
65533
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools
®
.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2008 by Harbor Freight Tools
®
. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SKU 65533 For technical questions, please call 1-800-444-3353. Page 2
SAVE THIS MANUAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month and
year of purchase if product has no num-
ber). Keep this manual and the receipt in
a safe and dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
General Safety Rules
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future
reference.
SAVE THESE INSTRUCTIONS
Work area safety1.
Keep work area clean and well a.
lit. Cluttered or dark areas invite
accidents.
Keep children and bystanders away b.
while operating. Distractions can
cause you to lose control.
Electrical safety2.
Do not expose tools to rain or wet a.
conditions. Water entering a tool
will increase the risk of electric
shock.
Do not abuse the cord. Never b.
use the cord for carrying, pulling
or unplugging the tool. Keep cord
away from heat, oil, sharp edges
or moving parts. Damaged or
entangled cords increase the risk of
electric shock.
Personal safety3.
Stay alert, watch what you are a.
doing and use common sense
when operating.
Dress properly. Do not wear loose b.
clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught
in moving parts.
Tool use and care4.
Do not use the tool if the switch a.
does not turn it on and off. Any tool
that cannot be controlled with the
switch is dangerous and must be
repaired.
Disconnect the plug from the b.
power source before making any
adjustments, changing accessories,
or storing tools. Such preventive
safety measures reduce the risk of
starting the tool accidentally.
Check for misalignment or binding c.
of moving parts, breakage of
parts and any other condition that
may affect the tool’s operation. If
damaged, have the tool repaired
before use. Many accidents are
caused by poorly maintained tools.
Service5.
Have your tool serviced by a a.
SKU 65533 For technical questions, please call 1-800-444-3353. Page 3
identical replacement parts. This
will ensure that the safety of the
tool is maintained.
Specic Safety Rules
Maintain labels and nameplates on 1.
the Vacuum. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
Do not use the Vacuum on liquids or 2.
wet surfaces.
This product is not a toy. Keep it out 3.
of reach of children.
WARNING: Handling the cord on 4.
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and
birth defects or other reproductive
harm. Wash hands after handling.
(California Health & Safety Code §
25249.5, et seq.)
People with pacemakers should 5.
consult their physician(s) before
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition, people
with pacemakers should:
on.
avoid electrical shock.
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
Some dust created by vacuuming, 6.
power sanding, sawing, grinding,
drilling, and other construction
activities, contains chemicals
known [to the State of California] to
cause cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
cement or other masonry products
chemically treated lumber
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
particles. (California Health & Safety
Code § 25249.5, et seq.)
The warnings, precautions, and 7.
instructions discussed in this
instruction manual cannot cover all
possible conditions and situations that
may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
be built into this product, but must be
supplied by the operator.
SKU 65533 For technical questions, please call 1-800-444-3353. Page 4
SPECIFICATIONS
Electrical Requirements 12 VDC, 4 Amps
25,000 RPM
Fuse Type 7 Amp, 250 V
UNPACKING
When unpacking, make sure that
the item is intact and undamaged. If any
parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Push the Tool Adaptor (9) into the 1.
front of the unit and connect the de-
sired attachment (8, 10) to the Adap-
tor. The Hose (7) can be connected
to the Tool Adaptor and an attachment
to reach further.
Plug the end of the Cord (6) into a 2.
compatible 12 VDC power socket.
Push the On/Off Button (4) forward to 3.
start the Vacuum.
Empty the dust bag after each use. 4.
To prevent accidents, turn off the 5.
tool and disconnect its power supply
after use. Clean, then store the tool
indoors out of children’s reach.
USER-MAINTENANCE
INSTRUCTIONS
Procedures not specically
explained in this manual must
be performed only by a qualied
technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Cleaning, Maintenance, and
Lubrication
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
THE FUSE, 2. must be replaced after it
blows. The unit will not function with
a blown fuse. Turn the Tip at the end
of the Plug counterclockwise to re-
move it. Remove the Contact and the
old Fuse, replace with a new 7 Amp
glass fuse and return items to original
orientation. See picture, next page.
SKU 65533 For technical questions, please call 1-800-444-3353. Page 5
Cord (6)
Tip
Contact
Fuse
FILTERS, 3. must be changed when
they become too clogged to be ef-
fective. Push the Release Button (3)
and remove the Canister (2), remove
can be cleaned using pressurized air.
continuing.
AFTER USE,4. clean external surfaces
of the tool with clean cloth.
WARNING! If the supply cord of this
power tool is damaged, it must be
replaced only by a qualied service
technician.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DIS-
TRIBUTOR HAS PROVIDED THE PARTS
OR DISTRIBUTOR MAKES ANY REP-
RESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE
TO THE PRODUCT, OR THAT HE OR
PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DIS-
-
-
CIANS, AND NOT BY THE BUYER. THE
-
OR ARISING OUT OF HIS OR HER IN-
THERETO.
SKU 65533 For technical questions, please call 1-800-444-3353. Page 6
PARTS LIST & ASSEMBLY
DIAGRAM
Part Description Qty
1 Filter (inside canister) 1
2 Canister 1
3 Release Button 1
4 On/Off Button 1
5 Motor Housing 1
6 DC 12V Cord/Plug 1
7 Hose 1
8 Crevice Attachment 1
9 Tool Adaptor 1
10 1
11 Brush 1
12 Storage Bag (not shown) 1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
-
1
-
2
-
3
-
4
-
5
-
6
Chicago Electric 65533 Operating Instructions Manual
- Category
- Power tools
- Type
- Operating Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chicago Electric 96325 User manual
-
-
-
-
Chicago Electric 94071 User manual
-
-
-
-
-
Other documents
-
CHICAGO 93353 Assembly And Operating Instructions Manual
-
Harbor Freight Tools 92917 User manual
-
-
Pacific hydrostar 47906 Set Up And Operating Instructions Manual
-
Drill Master 42307 User manual
-
Central Machinery 43533 User manual
-
-
-
-
