Western Rubber Cutting Edge Assembly Parts List & Installation Instructions

Brand: Western

Model: Rubber Cutting Edge Assembly

Type: Parts List & Installation Instructions

I ~

WESTERN PRODUCTS

7T NORTH 73RD STREET

P.O. BOX 23045

MILWAUKEE, WISCONSIN 53223

A DIVISiON OF DOUGLAS DYNAMICS, INC.

Rubber Cutting Edge Assembly

INSTALLATION INSTRUCTIONS,

DIAGRAMS & PARTS LIST

WARNING: Block blade in a raised pösition when installng rubber cutting edge. A fallng blade

can cause se.rious injury.

1. Raise blade and position on blocking.

2. Remove steel cutting edge.

3. If required, cut rubber cutting edge and clamp bar as shown in diagrams 1, 2, or 3 below.

4. Install rubber cuting edge, clamp bar, and bolts and

locknuts. Position cutting edge as-high as slots permit be-

fore- tightening bplts.

5: As rubber cutting edge wears; loosen bolts and slide it

down. - Reverse cutting. edge when top of slots is reached.

Install with

bottom end of

slot against

carriage bolt.

Diagram No. 1 - (For 6'6", l' or 7'6" blades)

7' Cut Off

_ 6'6" Cut Off

Il~ n

3.L...l

. 6"

oo U 0 oor r i

J J..311

7' Cut Off

6'6" Cut Off

Cut off both ends

7'6" NO CUT 7'6" 7'6" NO CUT

Diagram No.2 - (For 8',8'6", or 9' Blades except 9' Heavyweights)

8'6" Cut Off

8' Cut Off

I ~ ~ 0

. 3.L .l

6!'

~ !

o DUO oo l l I

J J 3t. 8'6" Cut Off

6" . 8' Cut Off

9' NO CUT

Cut off both ends

9' NO CUT 9'

Diagram NO.3 - (For 9' or 10' Heavyweight Blades)

o 0 ooll 0 oo 0 o 0

Only cut off end with two sets of double holes 12" 9' Cut Off

10' NO CUT

10'

Parts List And Diagram, See Page 2

For No. 1349504 -1- Printe In U.SA

PARTS LIST

Item Part No. Qty. Descr.iption

For 6'6", 7' or 7'6" blades - (Diagram No.1, page 1)

60825 1 RUBBER GUT ASSY 6'6" 7' 7'6"

1 . 60826 1 RUBBER CUT EDGE 6'6" 7' 7'6"

2 . 60827 1 CLAMP BAR 6'6" 7' 7'6"

3 . 90249 8 1/2-13X2-3/4 CB G5 ZP

4 . 91335 8 1/2-.13 PT HX LK NUT NYIS ZYC

PARTS DIAGRAM

For 8', 8'6", or 9' Blades except 9' Heavyweights - (Diagram No.2, page 1)

62556

1 . 62344

2 . 62346

3 . 90249

4 . 91335

RUBBER CUT EDGE ASSY8' 8'6" 9'

RUBBER CUT EDGE 8' 8'6" 9' (Except 9' Heavyweight)

CLAMP BAR 8' 8'6" 9' (Except 9' Heavyweight)

1/2-13X2-3/4 CB G5 ZP

1/2-13 PT HX LK NUT NYIS ZYC

For 9' or 10' Heavyweight Blades - (Diagram No. 3,page 1)

60831 1 RUBBER CUT ASSY 9' 10'

1 . 60832 1 RUBBER CUT EDGE 9' 10' (Heavyweights)

2 . 60833 1 CLAMP BAR 9' 10' (Heavyweights)

3 . 90265 12 5/8-11 X2-3/4 CB G5 ZP

4 . 91337 12 5/8-11 PT HX LK NUT NYIS ZYC

Indented parts are included in the assembly under

which they are listed. Quantities shown are in-

cluded with the assembly.

ABBREVIATION KEY

ASSY Assembly

CB Carriage Bolt

G Grade

HX Hex (Head)

LK Lock

NYIS Nylon Insert

PT Prevailng Torque

ZP Zinc Plated

ZVC . Zinc Yellow Chromate

For No. 134950 -2- Printe In u.S.A

Western Rubber Cutting Edge Assembly Parts List & Installation Instructions

Western Rubber Cutting Edge Assembly Parts List & Installation Instructions

Western Rubber Cutting Edge Assembly Parts List & Installation Instructions

Related papers

Other documents