User’s Guide

Model: H2ORB-RGWB-FC7NS

H2Orb™

SAVE THESE INSTRUCTIONS

Please ONLY use

manufacturer-provided USB

cord. Max 5V/2A adapter.

TABLE OF CONTENTS

Notice ..............................................................................................................................1

Parts List ..........................................................................................................................3

Setting up the Light ...................................................................................................4

Default Settings ...........................................................................................................5

Product Specications ............................................................................................... 5

Limited Warranty .........................................................................................................6

Caution ............................................................................................................................ 6

Cleaning Instructions .................................................................................................6

Disposal...........................................................................................................................6

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that

to which the receiver is connected.

• Do not submerge the unit or leave in the water for extended periods of time.

• Do not store or use this device near ammable gasses.

• Do not place the light inside a microwave or high voltage equipment.

• Follow the battery safety and charging safety guidelines when charging the unit.

BATTERY SAFETY

• Do not attempt to take apart or repair this unit. This can lead to leakage, re, or

• Do not ship the unit in stand-by mode or with a charged battery, as this could result

• Do not dispose of the battery as household waste. Refer to local regulations for disposal.

• All rechargeable batteries have a limited lifespan. After many repeated charging

Important Health & Safety Notice

PHOTOSENSITIVE EPILEPSY: IF YOU HAVE A HISTORY OF EPILEPSY OR SEIZURES, CONSULT A

DOCTOR BEFORE USE. CERTAIN PATTERNS MAY TRIGGER SEIZURES WITH NO PRIOR HISTORY.

BEFORE USING THIS PRODUCT, CAREFULLY READ THE INSTRUCTION MANUAL.

Important Health & Safety Information

Seizures induced by light stimulation (Photosensitive Epilepsy)

If you have an epileptic condition or have had seizures, consult your doctor prior to using

Eye soreness, altered vision, migraine, muscle twitching, convulsion or other involuntary

movements, blackout, loss of awareness, or confusion or disorientation.

In addition to the above, DISCONTINUE USE IMMEDIATELY if you experience any of the

following symptoms:

Headache, dizziness, nausea, fatigue, similar symptoms to motion sickness, or discomfort or

pain in any body part such as eyes, ears, hands, arms, feet whilst watching.

If the condition persists, seek medical attention.

CHARGING SAFETY

• To avoid risk of electric shock, dry the unit completely before charging.

• The charging cord is intended for indoor use only.

• Maximum safe charging temperature is 30ºC/86ºF.

• Ensure the charging port is clean and free of debris before charging.

• Do not connect your battery to a high-voltage power supply as this could result in

• Do not touch the charger or charging port with wet hands.

• Do not place heavy items on the power cord.

• Unplug the charger before cleaning the device.

• Unplug the charger when the device is not in use.

IMPORTANT NOTE:

The H2Orb is designed to be used with a power adapter that is 4.65 - 5.2V max. DO NOT

between 41°F to 100°F (5°C to 37°C).

ensure that all parts are present and in good condition. Notify the retailer immediately and

retain packing material for inspection if any parts appear damaged from shipping or the

carton itself shows signs of mishandling. Save the carton and all packing materials. In the

event that the xture must be returned, it is important that the xture be returned in the

original factory box. Please see parts list below for box contents.

PARTS LIST:

1) H2Orb

SETTING UP THE LIGHT

until the eect turns o. Stand-by mode holds a charge for roughly12 hours. The red

indicator light will ash when battery is low. If there is no light, the battery is depleted.

3. Short press the power button to adjust brightness. Short press the middle button

to cycle through default projection/swirl eects. Short press the last button to cycle

through preset LED colors.

4. The H2Orb has a built-in battery saver mode. It also has a light sensor, which allows

the light to turn on automatically when it gets dark, and a motion sensor, which can

control power on/o with a hand wave near the unit. These are all features that can be

toggled on or o via the physical buttons or the app. See the chart below for detailed

button functions.

DEFAULT SETTINGS

Once the unit is turned on, it will enter the default mode where all eects are on. This light

has a rechargeable battery that is designed to last for approximately 6 hours of operation.

Use the BlissHome app to control brightness, control eect color, set rotation speed, and