HySecurity SlideSmart DC Rodent Barrier Plate Installation guide

  • Hello! I've analyzed the installation instructions for the HySecurity SlideSmart DC Rodent Block Plate Kit (MX4366), which helps to protect the gate operator's electrical components from rodent damage. This document provides a step-by-step guide for a technician to install the plate, including necessary tools and parts. I'm ready to answer any questions you have about the installation process or the product itself.
  • What tools are required for installation?
    What is the purpose of the Rodent Block Plate?
    What should be done before starting the installation?
11 support.hysecurity.com
Installation Instructions
SlideSmart DC™ Rodent Block Plate Kit (MX4366)
The following instructions are intended to assist the user in the installation of the Rodent Block Plate in SlideSmart
DC™ gate operators. The plate prevents rodents from entering and damaging SlideSmart DC™ electrical
components. Please read all installation instructions before installing the kit.
REQUIRED TOOLS:
SlideSmart DC™ Cover Key
1/4" , 7/32" Allen Wrench
15/16" (x2) , 9/16" Open-ended Wrench
Blue Loctite™ #242
PARTS:
Verify that all parts are accounted for. See Figure
1 and Table 1.
Figure 1. Rodent Block Plate Kit
WORK SAFETY:
Only a qualifi ed service technician with proper
training should perform this installation. Follow
all shop safety rules and best practices when
performing this installation.
PREPARATION:
1. Make sure gate operator is turned off and
moving components are idle.
RODENT
BLOCK
PLATE
INSTALLATION
INSTRUCTIONS
BLUE
LOCTITE #242
23
4
1
Table 1. Rodent Block Plate Kit
Item
No. Part No. Description QT Y. Notes
1 MX4366 Rodent Block Plate Kit Includes
Items 2-4
2 MX4240 Plate, Rodent Block 1
3 MX001137 Loctite™ #242 1
4 D0840 Instructions, Rodent
Block Plate Installation 1
2. Unlock and remove cover using key.
3. Set the cover aside.
INSTALLATION:
1. Use a 7/32 inch allen wrench and 9/16
inch open-ended wrench to remove flat
head screws (2), fl at washers (2), and nylon
locknuts (2) from idler mount plate. See
Figure 2, A.
2. Set idler mount plate aside.
3. Disconnect magnetic proximity sensor
wires (4) on idler mount plate (1) from main
electrical harness. See Figure 2, B.
4. Use two open-ended 15/16 inch wrenches to
remove roller chain idlers (2), bolts (2), at
washers (6), bushings (2), and nylock nuts
(2) from idler mount plate. See Figure 2, C.
5. Use an 1/4 inch allen wrench to remove set
screws (2) and sprocket (1) from gearbox
shaft. See Figure 2, D.
6. Align rodent block slide plate (1) ush to
SlideSmart DC™ chassis ensuring bended
section avoids contact with gearbox. See
Figure 2, E.
7. Secure rodent block plate by performing Step
1 through Step 5 in reverse order.
CAUTION
DO NOT over-tighten bolts during reassembly.
Over-tightened bolts may damage bushings
causing wheels to drag.
22
D0840 Rev. E ©2022
NYLON
LOCKNUT
(2)
1APPLY BLUE LOCTITE #242
WHEN RE-INSTALLING.
NOTE:
1
BLUE
LOCTITE #242
A
B
C
D
E
SET
SCREWS (2)
SPROCKET (1)
ROLLER CHAIN
IDLERS (2)
FLAT
WASHER (6)
BUSHING
(1)
IDLER
MOUNT
PLATE
(1)
NYLOCK
NUT (2)
BOLT
(2)
FLAT
WASHER (2)
FLAT HEAD
SCREW (2)
RODENT
PROOFING
PLATE (1)
IDLER
MOUNT
PLATE
(1)
MAGNETIC
PROXIMITY
SENSOR (2)
ELECTRICAL
HARNESS
MAGNETIC
PROXIMITY
SENSOR
WIRES (4)
IDLER
MOUNT
PLATE
(1)
Figure 2. Rodent Block Plate Installation
BEFORE Rodent
Plate Install AFTER Rodent
Plate Install
/