Endres+Hauser WirelessHART Test Kit SWT70 Operating instructions

Brand: Endres+Hauser

Model: WirelessHART Test Kit SWT70

Category: Modems

Type: Operating instructions

Products Solutions Services

BA01205S/04/EN/02.15

Produktversion 1.00.xx

71308243

Operating Instructions

WirelessHART Test Kit SWT70

Test system for WirelessHART connections

WirelessHART Test Kit SWT70

Endress + Hauser 3

Table of contents

Revision history. . . . . . . . . . . . . . . . . . . . . . . . . 5

Registered trademarks. . . . . . . . . . . . . . . . . . . 5

1 Safety instructions. . . . . . . . . . . . . . . . . . 6

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Installation, commissioning and operation . . . . . . 6

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . 7

1.5 Radio approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.6 Technical improvement . . . . . . . . . . . . . . . . . . . . . . 8

1.7 Conventions used in this manual . . . . . . . . . . . . . . 9

2 Identification . . . . . . . . . . . . . . . . . . . . . 10

2.1 Unpacking the product . . . . . . . . . . . . . . . . . . . . . 10

2.1.1 Visual inspection . . . . . . . . . . . . . . . . . . . . 10

2.1.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . 10

2.1.3 Storage and transportation . . . . . . . . . . . 10

2.2 Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3 Ordering information . . . . . . . . . . . . . . . . . . . . . . . 11

2.4 Additional radio approvals . . . . . . . . . . . . . . . . . . 11

2.5 System requirements . . . . . . . . . . . . . . . . . . . . . . . 12

2.6 Licensing agreement . . . . . . . . . . . . . . . . . . . . . . . 12

3 Function and system design . . . . . . . . 13

4 Installation . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 14

5 Commissioning . . . . . . . . . . . . . . . . . . . 15

5.1 Display and operating elements . . . . . . . . . . . . . 15

5.2 Inserting and connecting the battery unit . . . . . . 15

5.3 Connecting the HART modem and installing the

modem driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.4 Installing the operating program . . . . . . . . . . . . . 17

5.5 Configuring the WirelessHART Test Kit . . . . . . . 18

6 Maintenance and repair. . . . . . . . . . . . 22

6.1 Battery units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.1.1 Replacement . . . . . . . . . . . . . . . . . . . . . . . . 22

6.2 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.3 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.4 Contact addresses at Endress+Hauser . . . . . . . . . 23

7 Troubleshooting . . . . . . . . . . . . . . . . . . 24

8 Technical data . . . . . . . . . . . . . . . . . . . . 25

8.1 Output/wireless interface . . . . . . . . . . . . . . . . . . 25

8.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8.3 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8.4 Mechanical construction . . . . . . . . . . . . . . . . . . . 27

8.5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8.6 Certificates and approvals . . . . . . . . . . . . . . . . . . 28

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

WirelessHART Test Kit SWT70

4Endress + Hauser

WirelessHART Test Kit SWT70

Endress + Hauser 5

Revision history

Registered trademarks

HART®, WirelessHART®

Registered trademarks of the HART Communication Foundation, Austin, USA

Microsoft®, Windows®, Windows XP®, Windows Vista ®, Windows 7 ®and the Microsoft logo

are registered trademarks of the Microsoft Corporation.

Acrobat Reader® is a registered trademark of Adobe Systems Incorporated.

All other brand and product names are trademarks or registered trademarks of the

individual companies and organizations in question.

Product

version

Manual Changes Remarks

1.00.00 BA01205S/04/en/01.12 Original –

1.00.xx BA01205S/04/en/02.15 General Adaption CD/CI

All information about hazardous

areas removed

Safety instructions WirelessHART Test Kit SWT70

6Endress + Hauser

1 Safety instructions

1.1 Designated use

The WirelessHART Test Kit SWT70 is a test system for individual WirelessHART

connections. The WirelessHART Test Kit consists of two WirelessHART test adapters

SWA70 with special test firmware, magnetic fittings and an operating program. The two

WirelessHART test adapters can be configured as a transmitter or receiver and are used to

test and measure individual wireless connections in a WirelessHART network.

The WirelessHART test adapters SWA70 in the WirelessHART Test Kit SWT70 may not be

used to operate field devices. The WirelessHART test adapters SWA70 may not be

permanently installed in a facility or connected to a WirelessHART network.

1.2 Installation, commissioning and operation

The WirelessHART Test Kit SWT70 can be operated safely in compliance with the current

technical safety standards and the applicable EU guidelines.

The WirelessHART Test Kit can be a source of danger if it is not mounted correctly or if it is

used in applications for which it is not intended.

The WirelessHART Test Kit may only be installed, commissioned, operated and maintained

by trained, qualified specialists authorized to perform such work by the facility's owner-

operator. The specialist staff must have read and understood these Operating Instructions

and must follow the instructions they contain. The devices may not be modified or repaired

in any way.

These specifications also apply for the battery unit.

1.3 Operational safety

Applications The WirelessHART Test Kit SWT70 meets the requirements of the EU guidelines for the

various range of applications envisaged for the device. The permitted operating conditions

must be observed. See “Technical data” on page 25.

Battery unit In the WirelessHART Test Kit, power is supplied to the WirelessHART test adapters via high-

power lithium-thionyl chloride battery units. This has implications for operational safety

and storage. Please refer to the hazardous materials regulations provided in the

accompanying Safety Data Sheet (CD-ROM folder: Safety Data Sheet).

The battery units can remain in the test adapters. Once the testing period has elapsed, the

test adapters quit wireless operation and therefore no additional energy is used.

Warning!

• Any tampering with the antenna, electronics or battery unit invalidates Endress+Hauser’s

warranty along with the telecommunications approval.

WirelessHART Test Kit SWT70 Safety instructions

Endress + Hauser 7

Maintenance In the case of the WirelessHART Test Kit, the battery units are the only components that may

be replaced. The WirelessHART Test Kit may not be repaired.If the device is faulty or

malfunctions, return it to Endress+Hauser. Follow the instructions outlined in the “Return”

auf Seite 23. The battery unit must be removed before the device is returned.

1.4 Declaration of Conformity

All the Declarations of Conformity can be found on the accompanying CD-ROM in the

"Documentation\SWT70\Certificates" folder.

EC Declaration of

Conformity

/CE mark

The WirelessHART test adapter SWA70 meets the legal requirements of the relevant

EC guidelines. Endress+Hauser confirms that the WirelessHART test adapter SWA70 has

been successfully tested by affixing to it the CE mark.

Electromagnetic

compatibility

All the modules are suitable for industrial use and meet the conditions of European Directive

2004/108/EC "Electromagnetic Compatibility":

• Interference emission:

EN 61326-1: 2006, Class B

Interference immunity:

EN 61326-1: 2006 Tab. 2 (Industry)

NE21

Safety instructions WirelessHART Test Kit SWT70

8Endress + Hauser

1.5 Radio approvals

Caution!

• A distance of at least 20 cm must be maintained at all times between the device antenna and the

body of the user or any other person in the vicinity irrespective of the application or use.

Note!

• Changes or modifications to the WirelessHART Test Kit that have not been expressly

approved by Endress+Hauser will render invalid the user’s right to operate the test kit.

Brazilian approval ANATEL 2759-11-7311 (EAN Number: 7898994191421)

“Este produto está homologado pela ANATEL, de acordo com os procedimentos

regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados.”

Para maiores informações, consulte o site da ANATEL www.anatel.gov.br

Chinese approval This device has been granted a type approval by the SRRC (State Radio Regulatory

Commission of P. R. China): CMIIT ID 2011DJ5309

ETSI approval

(R&TTE approval)

This device meets the requirements of the EC Telecommunications Directive 1999/5/EC

• EN 300 328: V1.7.1 (2006-10)

• EN 301 489-1: V1.81. (2008)

• EN 301 489-17: V2.1.1 (2009)

FCC and IC approval

(IC=Industry of Canada)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any

interference received, including interference that may cause undesired operation.

Japanese approval This device has been granted a designation number by the Japanese Ministry of Internal

Affairs and Communications according to the Ordinance concerning Technical Regulations

Conformity Certification etc. of Specified Radio Equipment

( )

• Article 2 clause 1 item 19

• Approval n°: 202WW09117711

This device should not be modified (otherwise the granted designation number will be

invalid).

Mexican approval COFETEL RCEPNSW12-0650

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que

este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo

debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no

deseada.

1.6 Technical improvement

Endress+Hauser reserves the right to make technical improvements to the hardware and

software anytime without prior notice. Such improvements are not documented if they do

not affect the operation of the device. A new version of the Operating Instructions is created

if the improvements affect operation.

WirelessHART Test Kit SWT70 Safety instructions

Endress + Hauser 9

1.7 Conventions used in this manual

Typographical emphasis and special symbols have been used to provide a clear structure to

the contents of these Operating Instructions and to highlight important information.

Pay particular attention to the safety conventions and icons used in these Operating

Instructions.

Safety instructions

Electrical symbols

Symbol Meaning

Danger!

This symbol alerts you to dangerous situations. Failure to heed the instructions will

result in a serious or fatal injury.

Warning!

This symbol alerts you to dangerous situations. Failure to heed the instructions can result in

a serious or fatal injury.

Caution!

This symbol alerts you to dangerous situations. Failure to heed the instructions can result in

a mild to medium injury.

Note!

This symbol refers you to procedural information and other facts that do not result in

physical injury.

Symbol Meaning

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

Alternating current

A terminal to which alternating voltage (sine-wave) is applied or through which

alternating current flows.

Ground connection

A grounded terminal which, as far as the operator is concerned, is already grounded via a

grounding system.

Protective ground connection

A terminal which must be connected to ground prior to connecting any other terminals.

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a

potential equalization line or a star grounding system depending on national practice or

company codes of practice.

Identification WirelessHART Test Kit SWT70

10 Endress + Hauser

2 Identification

2.1 Unpacking the product

2.1.1 Visual inspection

When unpacking the product:

• Check the packaging for visible signs of damage in transit.

• Remove the packaging carefully in order to prevent any damage.

• Keep the documentation supplied with the adapter in a safe place.

2.1.2 Scope of delivery

Check that the delivery is undamaged and that nothing is missing before you start

commissioning.

The WirelessHART Test Kit is supplied in a case. The delivery comprises:

• 1 storage medium with the operating program

• 2 modified WirelessHART test adapters SWA70 with magnetic fittings

• These Operating Instructions

Warning!

• If you discover that the battery unit is damaged, proceed as described in the Safety Data

Sheet on the CD-ROM.

• If you discover that the WirelessHART Test Kit SWT70 is damaged, the test system may

not be put into operation.

In this case, contact your Endress+Hauser sales partner. Where possible, return the device

to Endress+Hauser in its original packaging.

2.1.3 Storage and transportation

While the WirelessHART Test Kit is a robust device, appropriate precautions must be taken

to ensure proper storage and transportation:

Storage

Transportation When transporting the WirelessHART Test Kit it must be protected against strong vibrations

or shock.

Warning!

• High-power lithium-thionyl chloride batteries are classified as a Class 9 hazardous

material (HAZMAT Class 9: Miscellaneous).

Condition WirelessHART Test Kit

without battery units

Separate battery unit

Temperature –40 to +85°C/–40 to 185°F Maximum: < 30 °C/86 °F

Recommended 1): < 21 °C/70 °F

Special safety measures None Store in a cool, well-ventilated

environment away from moisture, sources

of heat, naked flames, food and beverages

1) A storage temperature < 21 °C/70 °F is recommended to minimize self-discharging of the battery unit.

WirelessHART Test Kit SWT70 Identification

Endress + Hauser 11

2.2 Nameplate

The nameplate is located on the side of the WirelessHART test adapter, and contains all the

important information such as the order code, serial number and radio approvals. Additional

information about the radio approval is provided on a separate adhesive label. See Figure 2-

2 on page11.

Fig. 2-1: Nameplate (example)

2.3 Ordering information

The WirelessHART Test Kit SWT70 can be ordered with the following approvals:

• 71307754

An additional sticker identifies the test adapter as an integral part of a WirelessHART Test

Kit SWT70, so it is impossible to mix the test adapter up with a normal WirelessHART

adapter SWA70.

2.4 Additional radio approvals

An adhesive label on the antenna lists additional radio approvals.

Fig. 2-2: Location of the adhesive label that lists the additional radio approvals

1 Order code

2 Serial number

3 Radio approval

Made in Germany, D- 79689 Maulburg

XA506F-X

-40°C Tamb +60°C≤≤

XXXXXXXXXXX

Ser.No.:

SWA70-I11A1A1+IKIWZ1

2010-02

NEMA4

0976

Dat.:

1 2

202WW09117711

CMMIT ID 2011DJ5309

Identification WirelessHART Test Kit SWT70

12 Endress + Hauser

2.5 System requirements

An operating program is supplied on a data storage medium for the WirelessHART Test Kit.

The operating program can be used with the following operating systems:

• Microsoft Windows 7 (32-bit, 64-bit)

• Microsoft Windows Vista Ultimate (32-bit)

• Microsoft Windows XP Service Pack 2 and 3 (32-bit)

Windows XP/Vista MUI packs (multilingual user interface) are not supported. If another language

is required, you must install the corresponding version of Windows XP/Vista.

2.6 Licensing agreement

The complete licensing agreement can be found on the CD-ROM. The software required to

read out data and commission the device is either available free of charge or is subject to the

licensing conditions of the manufacturer. By installing the software on your computer you

agree to accept the conditions of the specific licensing agreement.

WirelessHART Test Kit SWT70 Function and system design

Endress + Hauser 13

3 Function and system design

The WirelessHART Test Kit SWT70 is a test system for individual WirelessHART connections. The

test system can either be used to solve problems in existing WirelessHART networks or used in

advance for project planning. The test system works independently of existing WirelessHART

networks.

The WirelessHART Test Kit SWT70 consists of two WirelessHART test adapters SWA70 with a

special test firmware, magnetic fittings and an operating program. Both WirelessHART test adapters

can be configured as a transmitter or receiver. The transmitter and receiver can be easily mounted

at the desired position using the magnetic fittings.

The transmitter and receiver are configured one after another via the operating program.

The transmitter transmits test packets cyclically to all the configured channels. The packets

received by the receiver are evaluated statistically, and the signal quality is determined in

this way.

Fig. 3-1: Structure of a WirelessHART Test Kit SWT70

Top (A): WirelessHART test adapter SWA70 configured as a transmitter

Bottom (B): WirelessHART test adapter SWA70 configured as a receiver and test phase

1 WirelessHART test adapter SWA70 as transmitter

2 HART modem e.g. FXA195

3 WirelessHART test adapter SWA70 as receiver

Installation WirelessHART Test Kit SWT70

14 Endress + Hauser

4 Installation

The WirelessHART test adapters of the WirelessHART Test Kit are mounted on magnetic

surfaces using the magnetic fitting.

4.1 Installation conditions

Note!

In order to avoid attenuation of the electromagnetic waves and any resulting impairment in

the operation of the WirelessHART test adapter, the following must be observed when

mounting the adapter:

• The antenna must be at least 6 cm away from a wall or post (1).

• The antenna of the WirelessHART test adapter should never be located between a wall/

post and the housing (2).

• There must be a distance of at least 6 cm between the antenna and any metal material

running parallel to it (3).

• The antenna must be aligned vertically, and point upwards (4).

• Ideally, there should not be any wall or similar between the transmitter and receiver.

Fig. 4-1: General installation instructions

Wall 12

Wall

Post

WirelessHART Test Kit SWT70 Commissioning

Endress + Hauser 15

5 Commissioning

5.1 Display and operating elements

Note!

• To avoid any restrictions in the functions, do not press the push button.

• All the display and operating elements inside the WirelessHART test adapter do not have

any function on account of the special test firmware.

5.2 Inserting and connecting the battery unit

When you put the unit into operation for the first time, you must open the test adapters in

order to insert the battery units. Please pay attention to the operational safety instructions.

See “Operational safety” on page 6.

Note!

• You require a Torx T10 to open the housing.

Fig. 5-1: Battery compartment with housing open

1 Light emitting diodes (no function)

2 Push button (do not press)

3 Socket for battery connector

4 Battery compartment

5 Terminals 1 to 6 (no function)

6 Terminals (no function)

Commissioning WirelessHART Test Kit SWT70

16 Endress + Hauser

Proceed as follows to connect the battery unit:

1. Insert the battery unit into the battery compartment, making sure that the battery unit

engages with a click.

2. Insert the battery connector into the socket.

3. Close the housing and tighten the housing screws.

Note!

• The battery unit can remain connected. So little energy is consumed that the battery unit

has a service life of maximum 10 years if the WirelessHART Test Kit is not used.

5.3 Connecting the HART modem and installing the mo-

dem driver

The WirelessHART test adapters must be connected to a HART modem for configuration and

measurement purposes. The driver for the HART modem must be installed on the same

computer that runs the "WirelessHART Connectivity Tester" operating program.

Fig. 5-2: Connecting a WirelessHART test adapter to a computer via a modem

Proceed as follows to connect the HART modem and to install the modem driver if it is not

already installed:

1. Connect the HART modem to the terminal lugs of the cable gland of the WirelessHART test

adapter.

– If the modem has a built-in communication resistor, this resistor must be switched on.

– If the modem does not have a built-in communication resistor, proceed as described

in the "Troubleshooting" section. See “Troubleshooting” on page 24., Number 1.

1 Computer with "WirelessHART Connectivity Tester"

operating program

2 Serial port e.g. USB or RS-232

3 HART modem e.g. FXA195

4 WirelessHART test adapter, transmitter or receiver of

the WirelessHART Test Kit

WirelessHART Test Kit SWT70 Commissioning

Endress + Hauser 17

2. Start the computer and then plug the connector of the HART modem into the appropriate

port.

– If you use a USB port, the computer recognizes new hardware. The device driver must

be installed as described in Steps 3-6.

– If you use an RS-232 port, the port is automatically connected to the COM

communication port. Steps 3-7 then do not apply.

3. Click Ok in the dialog box that appears to start the Found New Hardware Wizard.

– Select the Not this time option and press Next.

4. Insert the CD containing the modem driver into the CD drive and press Next.

5. Follow the instructions of the Wizard to install the device driver.

6. After the installation, you must unplug the USB connector and restart your computer.

7. If you insert the USB plug back into the USB port of your computer, the computer will

recognize the HART modem.

– To check the communication port, select Settings > Control Panel > System.

– In the System Properties dialog box, select the Hardware tab and click Device

Manager.

– Open Ports (COM LPT) and check the communication port that has been assigned to

the HART modem.

5.4 Installing the operating program

Proceed as follows to install the operating program:

1. Insert the CD supplied into the CD drive of your computer.

2. A Setup Wizard starts.

– Select the WirelessHART Connectivity Tester option.

– If the Setup Wizard does not start automatically, right-click the CD drive and select

Autoplay.

3. Click Setup.

4. The Setup Wizard is started.

– Click Next to continue the installation.

5. The License Agreement is displayed. Read the license agreement carefully.

– Select I agree and click Next to continue.

– Select I Do Not Agree to reject the agreement. Click Cancel to quit the installation.

Commissioning WirelessHART Test Kit SWT70

18 Endress + Hauser

6. The Select Installation Folder dialog box is displayed. An installation folder is suggested in

the Folder field.

– Click Browse to select another installation folder.

– Chose Everyone or Just me as the user.

– Click Next to continue.

7. The Confirm Installation dialog box is displayed.

– Click Next to start the installation.

– A status window indicates the progress of the installation process.

8. The following dialog box appears when the installation is finished.

– Click Close to close the dialog box and complete the installation.

5.5 Configuring the WirelessHART Test Kit

1. Mount one of the two WirelessHART test adapters at the position of the transmitter.

2. Connect the WirelessHART test adapter to the computer via the HART modem.

Starting the operating

program

3. Start the WirelessHART Connectivity Tester operating program by either clicking the

icon on the desktop or via the menu Start/Windows Icon > All Programs >

Endress+Hauser > WirelessHART Connectivity Tester.

4. The Select the Customer dialog box is displayed.

– Select a customer via the Customer field or enter a new customer name in the field.

– Click Ok. A folder is created for every customer. Path: My Files\WirelessHART

Connectivity Tester\[Customer Name]. All the results of the measurement are saved

to this folder.

WirelessHART Test Kit SWT70 Commissioning

Endress + Hauser 19

5. The Start dialog box is displayed.

Connecting the

transmitter

6. Select the Start Transmitter option to configure the WirelessHART test adapter as a

transmitter. Alternatively you can also choose from the following options:

– Start Receiver: configure the WirelessHART adapter as a receiver. The transmitter

must have already been activated with the same computer.

– Do Maintenance: read information from the WirelessHART test adapter and confirm

battery change.

7. The Connect to Transmitter dialog box is displayed.

– In the COM-Port field, select the port to which the HART modem is connected.

– Click Connect to establish the connection between the WirelessHART test adapter

and the HART modem. The Status field displays the communication status.

Note!

• You can only establish one connection to a WirelessHART test adapter of the test system

via the operating program. It is not possible to connect to other HART or WirelessHART

devices.

Configuring the

transmitter

8. Once the connection has been established successfully, the Transmitter dialog box is

displayed.

Commissioning WirelessHART Test Kit SWT70

20 Endress + Hauser

Configure the transmitter:

– Enter the location of the transmitter in the Location field.

– In the Duration of Test field, enter the total duration of the test from the current

transmission position. Please note the following.

– Select or deselect the channels to be tested in the Blacklist field. Channels 1 to 15 are

enabled by default. Channel 16 is generally not used by WirelessHART and is

therefore disabled.

Note!

• Enter the duration of the test via the Duration of Test field. If the duration of the test is

≤5 hours, the channel is changed every 15 seconds (short-term test). If the duration of

the test is > 5 hours, the channel is changed every minute (long-term test).

9. Click Start to start the test with the configured parameters. Once the test has been

started successfully, the status and the remaining operating life of the battery unit are

updated in the Transmitter Status field. The transmitter is configured.

Connecting the receiver 10.Click Connect to Receiver. The Connect to Receiver dialog box is displayed.

11.Disconnect the first WirelessHART test adapter (transmitter) from the HART modem.

12.Mount the other WirelessHART test adapter at the position of the receiver.

13.Connect the WirelessHART test adapter to the computer via the HART modem.

14.Make the following settings in the Connect to Receiver dialog box:

– In the Com-Port field, select the port to which the HART modem is connected. If you

have not changed the port you can make the settings as explained in Step 7.

– Click Connect to establish the connection between the WirelessHART test adapter

and the HART modem. The Communication Status field displays the communication

status.

Page is loading ...

Endres+Hauser WirelessHART Test Kit SWT70 Operating instructions

Brand: Endres+Hauser

Model: WirelessHART Test Kit SWT70

Category: Modems

Type: Operating instructions

Download PDF

report

Endres+Hauser WirelessHART Test Kit SWT70 Operating instructions

Endres+Hauser WirelessHART Test Kit SWT70 Operating instructions

Related papers

Other documents