CAMDEN CX-PS300UL User manual

Brand: CAMDEN

Model: CX-PS300UL

Type: User manual

CAMDEN CX-PS300UL is a power supply and charger designed for use with fire alarm systems. It provides a total of 3-amp nominal continuous supply current at 12/24V DC outputs and can accommodate one or two 12 Ah lead acid rechargeable batteries. The CX-PS300UL includes a built-in dedicated charger for sealed lead acid or gel cell type batteries, with a maximum charging current of 1.5 Amps. It also features automatic switch over to standby battery upon AC failure or below V, battery presence detection within 10 seconds, and a temperature compensated battery charger.

Page 1 of 9

CX-PS300UL

POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

Electrified Locks, Relays and Timers

1. DESCRIPTION

The CX-PS300UL series of power supply/charger supplies a total of 3-amp nominal continuous supply current @ 12/24V DC outputs.

It is installed in a large sheet steel enclosure capable of accommodating one or two 12 Ah lead acid rechargeable batteries. The

camden CX-PS300UL has been evaluated for ULC-S533, UL294 and ULC-60839-11-1. This power supply is not intended to power re

notication appliances (Horns, Strobes & Bells).

2. GENERAL SPECIFICATIONS

1. Input = 120 240V AC 50-60Hz, 1.4 Amp maximum.

2. Output 3 Amps continuous supply current PF 0.6 a t nominal 12/24 V DC.

3. Built-in dedicated charger for sealed lead acid or gel cell type batteries.

4. Maximum battery charging current 1.5Amps (not part of the max output current rating).

5. Automatic switch over to stand-by battery upon AC failure or below V .

6. Battery presence detection within 10 seconds.

7. Temperature Compensated Battery Charger. (EN54-4 only,not UL evaluated)

8. Battery Charger Monitor.

9. Battery load test every 48hr.

10. Battery test result indication.

11. Battery Reversal protection.

12. Low Battery indication at 11.40/22.80 Volts.

13. Low Battery disconnect at 10/20.2 Volts.

14. Low Battery, Battery disconnect, No Battery presence, battery charger trouble reporting. (See FAULT TABLE)

15. AC input indication by Green LED. (LED on when AC is present).

16. AC Fault CMOS Relay contact for AC failure

17. LEDs display on enclosure door (Green, Yellow, Blue).

18. DC output indication by Blue LED, on board and enclosure.

19. Overload and short circuit protection on DC output.

20. Battery charging leads included.

21. Board Dimension: 195mm x 110mm

22. Enclosure Dimension: 338 x 448 x 110mm (HP346 for 12Ah Battery)

Page 2 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

3. TECHNICAL SPECIFICATION:

Output Voltage

Output Amperage

Ripple

12/24 V DC Regulated. ClassE, unsupervised

3 Amp

50mVp-pmax

Charging Current

Battery Charging Voltage

1.5A Max, and not part of

max output rating

13.8V/27.6V Nominal

Operating Temperature 0 ˚C to 49 ˚C

4. PERFORMANCE RATINGS

UL294 Performance Levels:

Model

Product

Type

Line Security Destructive

Attack

Endurance

Standby Power

CX-PS300UL Power Supply I I IV III (when used with 12Ah

battery)

CAN/ULC-60839-11-1 Performance Grades:

Model Product Type

Grade

Grade Achievement

CX-PS300UL Power Supply

3 (when used with 12 Ah

battery)

Connect AC & battery

trouble relay outputs to

a grade 3 control unit, to

achieve Grade 3.

5 . LED INDICATIONS

1. Green LED- AC indicator

a. On when AC present.

b. The AC fail Relay activates (opens) within 60 seconds after AC failure.

2. BlueLED– DC Power indicator

a. Powered directly from the power supply DC output and indicates output is present.

3. YellowLED– Battery Charging and Fault indicator

a. The Yellow LED ashing indicates the battery is charging and is also used to indicate

various Fault conditions. See the Fault Condition and Indication table for details.

4. RedLED– Battery/ Charger test Indiicator for Pass or Failure.

a. The Red LED indicates a Battery test Failure or a Battery charger failure in conjunction with

the Yellow LED to indicate other Fault Conditions. See the Fault Conditions and Indication

table for details.

3 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

6. RELAY / OUTPUTS:

Output Output Type Description

AC FAIL NORMALLY CLOSED

OPEN = FAULT

TRIPS WITHIN 60 SEC. AFTER AC FAILS CMOS

RELAY RATING: 30V DC, 60 mA, 16 Ω

BATTERY FAIL NORMALLY CLOSED

OPEN = FAULT

BATTERY

PROBLEM

CMOS RELAY RATING: 30V DC, 60mA ,16 Ω

7. FAULT CONDITION & INDICATIONS:

FAULT LED-G LED-Y LED-R BATT

RELAY AC RELAY LED-B

BATTERY

REVERSED OR

NOT

CONNECTED

ON OPEN

BATTERY LOW ON OPEN

BATTERY

DISCONNECTED ON OPEN

BATTERY

TEST FAIL

5 RAPID FLASHES

STOP 1 SECOND

REPEAT UNTIL

BATTERY IS

REPLACED

OPEN

BATTERY TEST OK OFF

3 FLASHES

1 SEC ON/OFF

CHARGER FAIL

10 RAPID

FLASHES

2 SECONDS

STOP AND

REPEAT

UNTIL OK

OPEN

AC FAIL OFF

OPEN

WITHIN

60 SEC

DC FAIL /

OVERLOAD

OFF

Page 4 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

8. BATTERY OPERATING VALUES

Parameter Output Description

Battery Disconnect voltage 10/20.2V

When AC is o, the battery is disconnected when the battery

voltage drops below this value.

The battery is only reconnected when the AC is restored.

Minimum battery voltage to

pass battery test

11.50V

23.0V

Red LED should ash for 1 sec ON/OFF during 2 minutes

testing. 5 rapid ashes and 1 second pause indicates

battery failure. In such case replace battery.

Low Battery Voltage

Warning

11.40V

22.80V

If the out put voltage drops below this value, a voltage low

warning is generated. See Fault Conditions and Indication table.

9. INSTALLATION INSTRUCTIONS

This power supply should be installed in compliance with National Electrical Code, NFPA70 as well NFPA72 National Fire

Alarm Code, CSA C22.1, Safety Standard for Electrical Installations, Canadian Electrical Code, Part I, CAN/ULC-S524, and

all applicable Local Codes. Installation to be performed by suitably qualied personnel. The power supply shall not be

installed in the fail secure mode unless permitted by the local authority having jurisdiction, and shall not interfere with

the operation of Listed panic hardware.

NOTE: Connect the Mains AC input 120/240V AC as shows in the installation diagram. Entry knocks out on the left of the

enclosure. Keep low voltage wiring away from the AC wiring.

1. Mount the power supply in the desired location using the 4 mounting holes. NOTE: For use in indoor protected area with

controlled environment only. Do not install power supply on exterior doors.

2. With the main power disconnected, connect the LEDs to the AC input terminal block, respecting the wiring phase and polarity

: Ground/Earth=Green/Yellow, Neutral = Blue (White), Live =Black (Brown). This equipment must be connected to the 120-240

Volt Mains via a readily dedicated accessible external disconnect device with maximum 15 Amp branch protection. Select the

operating output DC voltage 12/24 with the jumper SW1. SW1 ON = 12V DC, SW1 OFF = 24V DC.

3. Do not connect the battery at this time.

4. Switch ON the AC power supply and with that Green LED will turn ON indicating AC is present and the AC Fault Relay will be

energized “ON” (closed). When the AC is o, the AC Fault Relay will drop open within 60 seconds (Factory set) activating the

CMOS output “AC Fail”. Connect this output to relevant monitoring devices.

5. Verify the DC output voltage. It should be13.20V DC or 26.40V DC (max). Blue DC LED will turn ON indicating DC output is OK.

6. Yellow LED will only turn on along with open BAT FAULT CMOS relay to indicate the Battery is not attached or connected with

reversed polarity.

7. Connect the Battery or Batteries with respective polarity. Note: Battery should not be connected if the AC is not present rst.

8. If the battery is connected with the correct polarities, the Yellow LED will turn OFF (See Fault Conditions and Indications Table).

Within one minute the Battery Fault Relay will restore and the Yellow LED will ash once every 2 seconds.

9. If the battery is connected with reverse polarity, the Yellow LED will remain ON. (See the Table Fault). The CMOS relay will be

open indicating Battery Fault. Connect this output to relevant monitoring devices.

10. Connect the devices to be powered to the output terminals marked “Vo- Vo+”.

11. See below Fig 1 & Fig 2. for installation of PD4ECB, PD8ECB, MOM8ECB and ACM4ECB need 2 EOLR Resistors (2K2) provided.

12. If Tamper Switch is required, use part # TSW1-02 or TWS2-02 (Refer Fig 3).

13. Use 2K2 EOLR (End Of Line Resistor) Part #EORL-PWX2K2.

14. Connect the fault relays to FACP or ACP for trouble indication.

15. Secure the enclosure with the screw or with the Key Lock (if provided).

5 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

10. ACM4ECB

DESCRIPTION:

The ACM4ECB is a distribution controller to be used with card Access Control, Egress Doors. It provides 12/24V DC through 4 outputs

rated 2.0A (max. 3A total) each with electronic over-current protection set at 2.5A. The 4 outputs will switch ON or OFF security

devices such as Magnetic Locks, Door Strikes, etc. It is connected to FACP or ACP via NO or NC congurable contact input using 2K2

EOLR (Part #EORL-PWX2K2). It also has an input for Reversed Polarity triggering. The ACM4ECB has 2 Dry Contact “Form C” relay

outputs, one is to indicate output status, and another to indicate DC failure on any of the 4 outputs, due to overcurrent or short.

Installation:

1. Output Connections

There are 4 selectable outputs suitable for FAIL safe cong and FAIL secure cong.

a) For FAIL safe operation, connect the positive (+) lead of the device to normally closed (NC) and the negative lead to COM ”Neg”,

connector CN1 to CN4. DC power is present in normal condition and switched OFF when the re alarm from FACP or ACP or Reverse

Polarity input is triggered. FAIL Safe operation devices such as, Magnetic Lock should be connected to this output as show in Fig. 2.

b) For FAIL secure operation, connect the positive(+) lead to Normally Open (NO) instead of normally closed (NC). DC power is not

present in normal condition and will switch ON when the FACP or ACP or Reverse Polarity input is triggered. FAIL secure operation

devices such as Door Strikes should be connected to this output.

2. Fire Alarm and Access Control Interface

Normally Open (NO), Normally Closed (NC) input or Polarity Reverse (Rev. Volt.) input are available to trigger the ACM4ECB

operation. Connect the positive(+) and Negative(-) from the FACP or ACP to the REV. VOLT terminals observing the polarity, (polarity

is referenced in alarm condition) or connect the NO or NC from the FACP or ACP output to the “Fire Trigger“ terminals. Install

PWX2K2 2k2 (EOLR) resistor at the FACP or ACP as show in Fig. 1. Note: No ELOR on Rev. Pol.

3.Engineering RESET/REX Input

This option is avaliable when the Jumper JL is removed (JL OFF). This will cause the ACM4ECB to latch upon receiving Input from the

FACP or ACP with this option in place and when the FIRE/ACP TRIGGER resets.

JL ON will cause the unit to follow the FIRE/ACP TIGGER. Install PWX2K2 2.2K (EOLR) resistor at the Key Switch or Push Button to

perform this operation.

4. Relay Output

a) DC Fail: When one or more of the 8 outputs fail due to over current or short circuit condition, the DC fail Relay will open. Connect

this output to monitoring device. (28V DC, 300mA)

b) Status Output: When the FACP or ACP input activates this will cause the dry contact Relay Form “C” to change state (de-energize).

Connect this output to monitoring device. (28V DC, 300mA)

5. ACM4ECB LED INDICATION

L1 to L4 are the Output RED LEDs, when ON they indicate DC is present (enable), and the Output relays are energized.

When OFF, they represent Relay is de-energized and the output is OFF, NO DC present (disable). LD1 to LD4 are Yellow LEDs. They

indicates overload or short on the output. The output current limit is set @ 2.5Amp, rated at max 2.0Amp. L9 Green LED is normally

OFF. It will switch on upon receiving an alarm from the FACP/ACP. This LED will stay ON following the status of the FACP/ACP input. If

JL was removed, this LED will stay ON until the manual RESET circuit resets.

6. Access Control Panel (ACP)Trigger input.

There are 4 inputs split between CN10 and CN11, each with four terminals, two IN and two GND. Activation of the inputs is achieved

by shorting IN and GND terminals of the respective inputs.

7. FACP/ACP Input Programming

Selectable Output to be Irrelevant on Fire Activation to have the output relay activation follow the FACP or ACP input place the DIP

switch corresponding to desired relay to the “OFF” position. In the “ON position, the correspondent output relay will not be aected

by the FACP,ACP or Rev. Pol input.

Page 6 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

8. Isolated Output Conguration

If any of the outputs requires to be solated DRY CONTACT, remove the respective Jumper J1 through J4 to achieve this conguration,

Form “C”, (C NO NC) available to connectors CN1 through CN4. This connection is now isolated from the internal power source. Relay

Rating: 28V DC, 2A. PF 0.6

7 of 9

CX-PS300UL POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

BATTERY 2

BATTERY CONNECTION NON POWER LIMITED

PWX2K2 EOL RESISTOR

QQ4

QQ3

QQ2

QQ1

SWITCH

DIP

JJ2

JJ1

REMOTE

RESET/REX

R/POL

FIRE TRIG.

OFF 3 2 1 4

SWITCH RELEVANT

FOR FIRE CONTROL

NO NC

CNC

ACM4ECB

FIRE

INPUT

EARTH

GND

POWER CONTROL STATUS

C NO NC

DC TRBL

POSITION TO OFF

NO NC NC

NO NC

POWERPLEX

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4

NC C NO COM (Neg) NC C NO COM (Neg) NC C NO COM (Neg) NC C NO COM (Neg)

IN GND IN GND IN GND IN GND

INPUTINPUT

INPUT

L1 J1 L2 J2 L3 J3 L4 J4

D17

C10

C13

CASCADE

LATCH

MODE

K1 K2 K3 K4

LY1 LY2 LY3 LY4

EARTH

GND

TO MONITOR POINT

RT2

CN3

CN2

CN6 CN7

D16

Q12

D17

C11

C47

IC9

Q12

Q11

C66

C37

LED-B

D25

C54 Q18

IC13

IC12

D5A

Q3A

CY2

CY3

CY6

NTC

OUTPUT

D.C.

BATT.

TEMP

FAIL

BATTERY

GND NL

BATTERY

- +

SW1

12/24

PANEL LED LED-Y LED-R

LED9

T4A/250Vac

NTC

LED-G

CX2

DB1

Q30

CX1

L1A

MOV

PROGRAM

VR1

FAIL

CY5

DX300

ELECTRIC DOOR STRIKE

INSTALL 2K2 EOLR AT FACP

ACP/FACP

2K2

EOLR

KEY SWICTH

MAGNETIC

LOCK

PWX2K2

EOL RESISTOR

POWERPLEX ELECTRONICS INC.

DX-200W-PCB

TAMPER

SWITCH

N/C TAMPER OUT

CONNECTOR

HPVM3 ASSY

TOP LEVER

DATE OF MFG

CABINET GROUND

AWG 14

EARTH

GROUND

STUD

AC INPUT

120 - 240 VAC

50-60Hz 1.4A

G N L

NOTE: PLEASE REFER TO CX-PS300 INSTALLATION MANUAL, PART NO:40-82B302 REV:01

CX-PS300UL

REGULATED POWER SUPPLY CHARGER

UL/ ULC LISTED AS FOLLOWS:

UL294, C A N / ULC60839-11-1,C A N / ULC-S533

POWER SUPPLY FOR ACCESS CONTROL SYSTEM

For use in Indoor

Dry controlled

Environment

G N L

(NEC AND CEC CLASS 2 CIRCUIT, 60950 LPS CIRCUIT)

3 2 3

LOAD (A)

[V]

24V

12V

12AH BATTERY 17.2AH BATTERY

STANDBY OPERATION

[HOURS]

TIME

VOLTAGE

OUTPUT STANDBY OPERATION

[HOURS]

TIME

EOLR

2K2

FACP/ACP

N/O CONFIG.

EOLR

2K2

N/C CONFIG.

2K2

EOLR

KEY SWITCH

N/C CONFIG.

FACP/ACP

FAIL SAFE CONFIG FAIL SECURE CONFIGURATION

KEEP POWER LIMITED WIRING FROM NON POWER LIMITED WIRING AT LEAST 0.25" INCH APART

FOR WIRING SIZE USE 22 TO 14AWG

ACCESS CONTROL

POWER

SUPPLY CHARGER

12/24 VDC 3.0Amp

CN1 CN2 CN3 CN4

CN10 CN11

RESET

EACH OUTPUT RATED AT 2.0AMP, Maximum 3 Amp Total

AMP BATTERY12 / 17.2

ULC-S533, UL 294

21A6

TESTED FOR:

ULC-60839-11 -1

SECURITY

SIGNALING

I.T.E. POWER SUPPLY

E220695

Battery capacity for loss of primary power

at least (see table below) hours for:

SECURITY EQUIPMENT

12 VOLT 12 VOLT

battery jumper

BATTERY 1

AWG14

LED’S PANEL

B AT

A C

GRN

DOOR

PANEL GROUND STUD

YEL

BLU

UL294, CAN/ULC-60839-11-1:

Grade 3"

SPECIAL LOCKING

ARRANGMENT

FIRE PROTECTIVE

This Product must be installed in compliance

with National Electrical CodeNFPA70,

and all applicable codes. CSA C22.1,

Safety Standard for Electrical Installations,

Canadian Electrical Code.

REG# T188047 1-02

REG# T188047 1-01

Canada

Industry

REG# T1880471-03

Fig. 1

TO FIRE INPUT

TERMINAL

TO REVERSED

POLARITY TERMINAL

STATUS

OUTPUT

2K2

EOLR

N/O CONFIGURATION

TO REMOTE RESET

FIRE ALARM MARSHAL OPTION

REMOVE JL

TO LACHT OUPUT

UNTIL REMOTE ACTIVATE

GND

EARTH

LY4

LY3

LY2

LY1

MODE

LATCH

CASCADE

C13

C10

D17

J4L4

J3L3

4321

INPUT INPUT INPUT INPUT

IN GND

NC C NO COM

NC C NO COMNC C NO COMNC C NO COM

OUTPUT 4 (Neg)

OUTPUT 3 (Neg)OUTPUT 2 (Neg)OUTPUT 1 (Neg)

POWERPLEX

NO NCNC

POSITION TO OFF

TRBL

NCNOC

STATUS

CONTROL

POWER

GND

EARTH

INPUT

FIRE

ACM4ECB

++NC

CNO

NCNO

FOR FIRE CONTROL

SWITCH RELEVANT

1 2 3 4

OFF

FIRE TRIG. +

R/POL

RESET/REX

REMOTE

JJ1

JJ2

DIP

SWITCH

KEY PAD

ACCESS CONTROL

PANEL

RELAY OUTPUT

UL N/0 PUSH BUTTON

OUTPUT 1 AND 4 ARE DESABLE TO THE ACP/FACP

OUPUT 2 AND 3 ARE ENABLE TO ACP/FACP

POWER FAIL

OUTPUT FAIL

CONNECT TO

MONITORING

TO AUXLIARY UL LISTED

POWER SUPPLY

NOTE:

IN THIS CONFIGUARTION

J4 MUST BE REMOVED

FOR ISOLATED CONTACT

CONNECTED TO DX300

KEY SWICTH

EOLR

2K2

MAGNETIC

LOCK

ELCTRIC DOOR

STRIKE

MAGNETIC

LOCK

USE UL LISTED EOL RESISTOR

USE ONLY UL LISTED EOL RESISTOR

PART NO: PX3007 REV:01

FIG 2

TYPICAL APPLICATION WIRING DIAGRAM

2 OR MORE CX-PS300 CONNECTED IN CASCADE

SECURE SAFE

CONFIGURATION

FAIL SAFE

CONFIGURATION

1 2 3

4 5 6

7 8 9

* # 0

LY4

LY3

MODE

LATCH

CASCADE

C13

C10

D17

J4L4

J3L3

NC C NO COM

OUTPUT 4 (Neg)

OUTPUT 3 (Neg)

POWERPLEX

NO NC

POSITION TO OFF

DC TRBL

C ON CN

STATUS

CONTROL

POWER

GND

EARTH

INPUT

FIRE

ACM4ECB

++NC

CNO

NCNO

FOR FIRE CONTROL

SWITCH RELEVANT

1 2 3 4

OFF

FIRE TRIG. +

R/POL

RESET/REX

REMOTE

JJ1

JJ2

DIP

SWITCH

LY4

LY3

MODE

LATCH

CASCADE

C13

C10

D17

J4L4

J3L3

NC C NO COM

OUTPUT 4 (Neg)

OUTPUT 3 (Neg)

POWERPLEX

NO NC

POSITION TO OFF

TRBL

C ON CN

STATUS

CONTROL

POWER

GND

EARTH

INPUT

FIRE

ACM4ECB

++NC

CNO

NCNO

FOR FIRE CONTROL

SWITCH RELEVANT

1 2 3 4

OFF

FIRE TRIG. +

R/POL

RESET/REX

REMOTE

JJ1

JJ2

DIP

SWITCH

EOLR

2K2

EOLR

REMOVE JR

TO CONNECT

IN CASCADE

NEXT ACM4ULECB

USE ONLY UL LISTED

EOL RESISTOR

KEY SWITCH

USE UL LISTED EOL RESISTOR

RESET CAN BE PERFORMED

ONLY FROM UNIT 1

TO FACP OR ACP

KEEP POWER LIMITED WIRING FROM NON POWER LIMITED WIRING AT LEAST 0.25" INCH APART

FOR WIRING SIZE USE 22 TO 14AWG

N/C CONFIGURATION

N/0 CONFIGURATION

2K2

REV POL.

CONTROL PANEL

ACP or FACP

2K2

1 INPUT ONLY

REV POL or FACP/ACP

INPUT CAN BE USED.

Page 8 of 9

CX-PS300 POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

Fig. 2

Call: 1.877.226.3369 / 905.366.3377

Visit: www.camdencontrols.com

Opening New Doors to

Innovation, Quality and Support!

CX-PS300 POWER SUPPLY / CHARGER

INSTALLATION INSTRUCTIONS

File: CX-PS300UL_Manual.indd

Rev.: September 19, 2022

Part No.: 40-82B302

Page 9 of 9

Fig. 3

Tamper Switch Connection

DICGU

VM3

CONNECT TO MONITORING POINTCONNECT TO MONITORING POINT

CONNECT TO MONITORING POINT

2 TAMPERS N/O

1 TAMPER N/O

CONNECT TO MONITORING POINT

N/C

N/O

N/C

N/O

N/C

N/O

EOLR

N/O

N/C

N/O

N/C

N/O

N/C

1 TAMPER N/C

2 TAMPERS N/C

File: CX-PS300UL_Manual.indd

Revision: JAN 30th 2023

Part No: # 40-82B302

Fig. 3

CAMDEN CX-PS300UL User manual

CAMDEN CX-PS300UL User manual

CAMDEN CX-PS300UL User manual

Related papers

Other documents