CAMDEN CX-PS150UL User manual

Brand: CAMDEN

Model: CX-PS150UL

Type: User manual

CAMDEN CX-PS150UL Power Supply

The CAMDEN CX-PS150UL Power Supply is a versatile and reliable power solution for access control and egress doors.

With its ability to supply a total of 1.7 amps nominal continuous supply at nominal 12/24VDC, it can power various access control devices, including magnetic locks, electric strikes, and access devices.

The built-in battery charger supports 1 - 4Ah batteries, providing backup power in the event of an AC power failure.

Additionally, the CX-PS150UL features overcurrent protection and battery reversal protection for enhanced safety and reliability.

CAMDEN CX-PS150UL Power Supply

The CAMDEN CX-PS150UL Power Supply is a versatile and reliable power solution for access control and egress doors.

The built-in battery charger supports 1 - 4Ah batteries, providing backup power in the event of an AC power failure.

Additionally, the CX-PS150UL features overcurrent protection and battery reversal protection for enhanced safety and reliability.

Page 1 of 3

CX-PS150UL

POWER SUPPLY / CHARGER FOR ACCESS CONTROL AND EGRESS DOORS

INSTALLATION INSTRUCTIONS

Electrified Locks, Relays and Timers

1. DESCRIPTION

This is a power supply /charger that supplies a total of 1.7 amps nominal continuous supply at nominal 12/24VDC. There are 2

outputs for Magnetic Lock or Electric Strike each with over current protected by 2.5 amp P.T.C. The CX-PS150UL can accommodate

1 - 4Ah battery. UL listed with UL294 Edition 7th. ULC-S533.

2. GENERAL SPECIFICATIONS

1. Input : 60Hz 1.8A max,120VAC for CX-PS150

2. Output 1 Amp continuous supply current at Nominal 12/24VDC controlled output for Maglock and Electric Strike.

Auxiliary Output 200mA at 12/24VDC for Access Device.

3. Built in Battery Charger of 500 mA for sealed lead acid or gel cell batteries.

4. Battery reversal protection.

5. Automatic switch over to stand-by battery upon AC failure.

6. LEDs display on enclosure door (LED Green for AC ,Led Blue for DC).

7. Enclosure dimension CX-PS150 8” x 9” x 3.5” (204mm x 231 x 89mm)

UL 294 7th Edition Access Control Performance Level:

Destructive Attack - I, Endurance - IV, Line Security – I, Standby Power – IV. Note: when using Standby

battery of 12VDC (CX-PS150UL) Standby Power rating is -- I.

3. BATTERY STAND-BY SPECIFICATION

Output: Stand-by 4 hr Alarm 5 min

12VDC /4AHBaery 500mA 1A

24VDC /4AHBaery 500mA 1A

This power supply should be installed in compliance with the National Electric Code (NFPA 70) CSAC22.1, Canadian Electric Code,

Part 1 and all applicable Local Codes. Installation to be performed byqualiedtechnical personnel.

Page 2 of 3

CX-PS150UL Power Supply

INSTALLATION INSTRUCTIONS

4. INSTALLATION

This power supply should be installed in compliance with the National Electrical Code (NFPA 70), CSA ,C22.1, Canadian Electrical

Code, Part 1 and all applicable Local Codes. Installation to be performed by suitably qualied technical personnel.

1. Mount the power supply in the desired location using the 4 mounting holes. NOTE: For use in Indoor Protected Area with

Controlled Environment only. Do not Install Power Supply in Exterior Conditions.

2. With the Mains power disconnected, connect the leads to the AC Input Fuse Terminal Block, respecting the wiring phase and

polarity :Ground/Earth=Green/Yellow, Neutral = White,(Blue), Live =Black (Brown). This equipment must be connected to the 120

Volt Mains via a readily dedicated accessible external disconnect device with maximum 15 Amp branch protection. Select the

operating output DC voltage 12/24 with the jumper. Jumper OFF 12VDC, Jumper ON 24VDC. Measure the output voltage before

connecting the MagLock or Electric Strike to conrm wright rate of the devices.

NOTE: Connect the Mains AC input 120/240VAC as shows in the installation diagram. Entry knocks out on the left of the

enclosure. Keep low voltage wiring away from the AC wiring.

3. Switch ON the AC. Green LED will come ON indicating AC is present , Blue LED will come ON indicating the output voltage is active.

4. Connect the locking device: Magnetic Lock respecting the positive polarity to terminal + Mag Lock and negative polarity to terminal

–COM. Electric Strike positive polarity to the terminal +STRIKE and the negative polarity to the terminal negative -COM.

Fire Alarm / Access Control Interface Connection

Normally Open (NO), Normally Closed (NC) input from the FACP or ACP are available to trigger PWX series operation. Connect the

NO or NC from the FACP or ACP output to the FIRE/ACP TRIGGER terminals. Install the 2K2 Ohm end of line resistor (EOLR provided)

at the FACP or ACCESS CONTROL PANEL as shown on the diagram. (Fig 1)

REX/Engineering Reset Input Connection

This option is available when the Jumper JL is removed (JL OFF). This will cause the PWX to latch upon receiving alarm from the FACP

or ACP with this option in place and when the FIRE/ACP TRIGGER resets, PWX will only reset by activating the RESET/REX input. JL ON

will cause the unit to follow the FIRE/ACP TIGGER. Install the 2.2K Ohms RESISTOR, Part provided at the Key Switch or Push Button to

perform this operation. (Fig 1)

5. Secure enclosure with 4 screws or lock if is provided.

VOLTAGE SELECTION CHART:

Output JV1 Posion Stand-by Load Alarm Load Baery (oponal)

12VDC OFF 500mA 1AMP 12VDC

24VDC ON 500mA 1AMP 24VDC

Terminal Block Connecon Descripon

ACAC Low voltage input from Transformer

AUX+/- Auxiliary 12/24 VDC out put to power Access Devices. Output not aected by

Fire Alarm Triggering, Access Request, Reset Switch.

FIRETRIGGER Supervised Fire Input with choice of N/O or N/C conguraon.

RESET Supervised input with choice of N/O or N/C conguraon Reset Switch to

reset to a normal operaon when in Latch Mode or Fire Marshal Operaon.

RequestAccess Shorng this input will unlock the MagLockor ElectricStrike.

Baery +/- Baery connecons for Stand-by operaon.

LED INDICATIONS:

GREEN LED ON AC ON, LED OFF LOSS OF AC

BLUE LED ON DC OUTPUT ON, LED OFF NO OUTPUT

YELLOW LED ON UNIT TRIGGRED BY FACP/ACCES CONTROL PANEL,

Call: 1.877.226.3369 / 905.366.3377

Visit: www.camdencontrols.com

Opening New Doors to

Innovation, Quality and Support!

Page 3 of 3

CX-PS150UL Power Supply

INSTALLATION INSTRUCTIONS

File: CX-PS150UL_Power_Supply_Manual.indd

Rev.: September 19, 2022

Part No.: 40-82B301

GREEN

WHITE

BLACK

FUSE

TRANSFORMER

AT LEAST 0.25" INCH APART

KEEP POWER LIMITED WIRING FROM NON POWER LIMITED WIRING

12/24VDC 300mA MAX.

GROUND

EARTH

JL OFF = LATCHING MODE

JV OFF = 12VDC, JV ON = 24VDC

LATCH JUMPER

SELECT VOLTAGE JUMPER

ACCESS CONTROL PANEL

TO OPEN LOCKING DEVICES

NORMALLY OPEN INPUT

N/0

SHORTING TO GROND

PANEL

CLASS 2 RATED POWER LIMITED

FIG.1

12/24VDC 1.0 AMP MAX.

CONNECTIONS DIAGRAM

STRIKE

ELECTRIC

OUTPUT

AUXLIARY

CONTROL PANEL

FIRE ALARM

N/C

N/O

CONFIG.

2K2 EOL

CONFIG.

N/O

N/C

LOCATION

RESET SWITCH

AC LED, DC LED

BATTERIES

STAND-BY

120VAC

FX1-V.02

KEY SWITCH

LACHT

FACP TRIG.

AC ON

JL OFF

YELLOW

GREEN

24V-ON

12V-OFF

ELECT.

LOCK

+MAG

+STKE

-COM

TRIGGER

FIRE

RESET

ACCESS

REQUEST

-BAT

+BAT

AUX

EGRESS FIRE EXIT DOOR

12345 612345

EARTH

GROUND

CN1 CN2

CN3

CX-PS150UL

PANEL

MAGNETIC

LOCK

CAMDEN CX-PS150UL User manual

Brand: CAMDEN

Model: CX-PS150UL

Type: User manual

CAMDEN CX-PS150UL Power Supply

The CAMDEN CX-PS150UL Power Supply is a versatile and reliable power solution for access control and egress doors.

The built-in battery charger supports 1 - 4Ah batteries, providing backup power in the event of an AC power failure.

Additionally, the CX-PS150UL features overcurrent protection and battery reversal protection for enhanced safety and reliability.

Download PDF

report

CAMDEN CX-PS150UL User manual

CAMDEN CX-PS150UL User manual

Related papers

Other documents