LinTronic TT455-RT-238 Quick Manual

Category
Car video systems
Type
Quick Manual
http://lintronic.dk
Get started
TT455-RT-238
Quick guide
Updated 190227
LinTronic
http://lintronic.dk
Get started
In this guide:
Step 1 - Getting started
Step 2 - CommandList
Step 3 - Memory Map
Step 4 - MyScore
Step 5 - MyFeedback
Step 6 - Dealers projects
http://lintronic.dk
Get started
Step 1 - Getting started
This is just a Quick Guide to get you started.
When you have studied this Quick Guide
- we recommend you read it all -
then use the Configurators
HELP button to find the
manual for the CommandList
and Memory Map
http://lintronic.dk
Get started
HELP / GET STARTED
- QuickGudes
NEWS / DOCUMENTATION
- manuals, videos
FIRMWARE UPDATES
- checks for updates of your products
BOOTLOADER
- updates your product
DATASAMPLER
- Comport monitor/control
LOG NOTEPAD
STATISTICS
- to be relased
http://lintronic.dk
Get started
IMPORTANT
FIRST
1. Read next pages about triggers and actions, so you understand the relation.
2. Download and install Configurator.
3. Insert your license related email and password from your customer profile.
4. Connect ComCab cables.
5. Open comport in Configurator.
Then
6. Apply power to your product.
7. Make sure you understand the difference between the
Step 1, CommandList and
Step 2, Memory Map
FAQ:
Our products are designed to work as standalone products with the possibility
of controlling other products by for example infrared, RS232 or relays.
Therefore a USB connector is not very useful in our products, as USB require
that the product is connected to a computer only and we would not be able to
control TV’s, projectors, light systems, relays, etc. etc.
It is strongly recommended that you familiarize yourself with the technical
manual of the product and the dedicated manuals for CommandList and
Memory Map.
See http://lintronic.dk | Support | Get started.
Best regards,
Michael Lindgaard
http://lintronic.dk
Get started
Triggers Actions
Triggers and Actions
Our products are controlled by Triggers, which causes Actions to be executed.
- A remote control command (Bang&Olufsen, Apple, Bose, LinTronic, Logitech, NEC, Samsung, etc.)
- A computer command (RS232 comport working on 2400 - 38400 bps)
- A switch, contact, relay, motion detector, etc. - connected to one or both of the 2 digital inputs
- An activation of the buttons, on the external receiver 8087030
- A 433 MHz signal from a remote control, motion/door/windows sensor, etc.
A Trigger can be for example:
Actions can be for example:
- InfraRed and/or RS232 signals for audio/video products, projectors, screens, curtains,
blinders, shades, light systems, relays, fireplaces, elevation beds, computer, etc.
- Digital or relay outputs for various purposes like relays, data-interface etc.
- 433 MHz signal controlling relays, doorbells, etc.
http://lintronic.dk
Get started
Triggers and Actions
The way you instruct your product on how to be Triggered and what Actions to control, is by setting up
a project which combines the Triggers and Actions.
STEP 1 - COMMANDLIST / ACTIONS
Before you start configuring your product to carry out what you want it to do, you need to get hold of the
commands (Actions) to be carried out. These commands (Actions) are collected in the CommandList.
In the CommandList you can use commands from the built-in database, which are commands shared by
other users uploading their commands to the online database.
If your product is not already covered/supported/shared, then you can copy commands from your own
remote control. If commands cannot be decoded, we can build a new decoder.
We kindly ask you to upload these commands to our database later, when you have tested they work.
RS232
If your product can be controlled by RS232 commands, (more and more screens, projectors, light systems,
etc.) then it is recommended to use RS232 instead of InfraRed, as InfraRed (IR) is much easier disturbed
than RS232.
RS232 requires a cable from the RS232-connector of the product.
In case you want to control another product by RS232 commands, and we do not have the required
commands, then we must embed the commands into the firmware for the product and we provide you with
a set of virtual commands which will generate the commands.
RELAYS
We support both wired and wireless relays, as well as relays controlled by RS232.
CUSTOMIZED SOLUTIONS
We often participate in development of special firmware which will allow our product to carry out your
specific tasks. We work fast and our prices are very attractive.
STEP 2 - MEMORY MAP
The Memory Map is where you select your Triggers and associate them with the Actions to be carried
out.
http://lintronic.dk
Visit - http://lintronic.dk | Support | Download
or
http://lintronic.dk/download.aspx
Download / install the Configurator
DOWNLOAD/INSTALL
http://lintronic.dk
From your online Customer profile:
Enter the license related Email and Password
from your customer profile.
Then generate your LicenseKey.
Please note:
If you later change your email address, then
the login and the license email can be different
as we will keep the first email for your license.
DOWNLOAD/INSTALL
http://lintronic.dk
Get started
Connect communication cable
to the TT455-RT-238.
Insert cable into computers serial
commport.
Serial cable: ComCab-001
Connect communication cable
to the product.
Insert cable into computer.
Do NOT install the enclosed CD.
Let the Windows 10 computer
find the driver online and auto-
install.
Serial cable: ComCab-003
CONNECT
http://lintronic.dk
Get started
Output
Power
Communication
Input Output
Connect computer cables
Insert ComCab-001 into TT455-RT-238 and insert ComCab-001
into computer, or
Insert ComCab-003 into TT455-RT-238 and insert ComCab-003
into computer.
CONNECT
Insert ComCab-004 into LIN-138/LIN-433
Insert ComCab-004 into ComCab-003
Insert ComCab-003 into computer
http://lintronic.dk
Get started
OPEN THE COMPORT ASSIGNED TO YOUR (USB) CABLE
CONNECT
= default
Click USB button in order to find USB port
http://lintronic.dk
Get started
+
-
Negative ring Positive tip
2.1 mm
1)
Front LED should blink for 2 seconds
and then turn on for ½ a second.
2)
Heart beat indicator blinks every second.
This indicator is best viewed from the side.
Follow the red arrow below.
Connect power.
If front LED's do not blink, check power
is set for 12 volt or turn the power plug
in the cable. The -238 is protected
against wrong polarity.
2.1 mm
1)
2)
1.5V 12V
100-240 vac
5 0 / 6 0 H z
12 volt
CONNECT
http://lintronic.dk
Get started
When the right comport is found there is no need to enter the Commport section again. The program
will/should remember the settings next time you start up.
Up to 32 products may work together in an industrial long-range 2-wire RS485 network.
If your product is still not detected:
- check that power supply is connected and set for 12 volt
- Products blinks for 2 seconds when power is applied
- If you use our USB-RS232 ComCab-002/003 cable, did you install the driver ?
- A driver update might be required.
Still no luck ? Contact LinTronic for OnlineSupport.
CONNECT
Product detected
http://lintronic.dk
Step 2 - CommandList
THIS IS WHERE YOU TEST COMMANDS/ACTIONS SO
YOU KNOW THEY WORK. THEN GOTO MEMORY MAP.
Update your database to get the latest commands uploaded
by other users.
Select a product closest to one of your products.
If you can find another typenumber than yours it will most
likely work.
- take it easy - start by testing a few commands
- start with a TV or a CD player
- test play, stop, power or eject
When you know how to handle a few commands you are
ready to move on - as everything is done exactly the
same way.
Mark a product as Favorite if you want to use it a
configuration project.
NEVER UPLOAD COMMANDS UNLESS YOU
HAVE TESTED THEM IN A PROJECT AND THEY WORK.
OTHERS USERS DEPEND ON YOU.
http://lintronic.dk
Get started CommandList
my database
- shows your products
update from online
- downloads new products
favorites
- your projects products
to be uploaded
- your new products
create new product
copy to new
delete
products
products commands
PRODUCTS
COMMANDS / ACTIONS
online codesets
codesets supported by your product
upload to shared database AFTER you have tested they work
Setting product to favorite, will allow you to add it to your projects
search
- in brandname
- in device
- in typenumber
instructs your product to send the selected IR command
when selected IR command is tested, this shows the command you can send from your homeautomation software
If the product performs the same command three times when tested, then adjust repeatnumber
down to 1 (001 - the range is 000 to 255).
If you can use the commands from this product, but your product holds a different typenumber,
then please copy the product into a new product and change the typenumber.
See the complete CommandList manual for more details - and how to copy commands
from your own remote control.
http://lintronic.dk
Get started CommandList
Read this
REPEATNUMBER
TYPENUMBER
http://lintronic.dk
Step 3 - MEMORY MAP
THIS IS WHERE YOU CREATE A PROJECT HOLDING
YOUR CONFIGURATION.
SPECIFY MODE/TRIGGER - SELECT RELATED ACTION.
THAT’S IT.
If you use a B&O remote, then insert the B&O receiver and
use the remote to set MODE and TRIGGER.
START SIMPLE !
Start by controlling a CD player (play, stop, eject) or
a TV (power on/off, channels, volume).
When you know how this works - you can virtually do all.
Get started
http://lintronic.dk
Get started
TT-IR-8087030
IR
Buttons
Included
LIGHT RADIO
TV
CD
DVD
SAT
VTAPE
RECORD
ATAPE
9
8
7
6
5
4
3
2
1
MENU
0
TEXT
GO
EXIT
LIST
STOP
>
>
BANG & OLUFSEN
>
>
>>
>>
Out2
Power
RS232
Input Out1
BUTTONS
INFRARED
If you want to use a B&O remote
as trigger:
See manual for the TT-IR-8087030 IR receiver:
http://lintronic.dk/AppNote_TTIR8087030.pdf
STEREO-EXT-10 (extra)
TRIGGER: B&O
TT455-RT-238
http://lintronic.dk
Get started
If you want to use a remote control
sending out LinTronic codes:
For easy configuration, choose LinTronic (codeset 745)
as trigger and operate the remote.
Point the remote at the front of the TT455-RT-238 and
operate the keys to set Mode and Trigger.
LogiTech Smart can be recommended allowing control
from your smartphone.
TRIGGER: LINTRONIC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

LinTronic TT455-RT-238 Quick Manual

Category
Car video systems
Type
Quick Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI