Pentair iChlor 523216 Installation guide

Brand: Pentair

Model: iChlor 523216

Type: Installation guide

iCHLOR™ SALT CHLORINE GENERATOR (SCG)

P/N 523216

FOR iCHLOR SCG PC100 POWER CENTER

INSTALLATION GUIDE

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

RISK OF ELECTRIC SHOCK! Disconnect all power from the Power Center at

the circuit breaker before starting any of these procedures. Failure to do so could

result in serious injury or death to servicemen, pool users or others.

Removing the Existing Circuit Board

1. Remove the Phillips-

head screw securing the

power center cover to the

enclosure, and remove the

cover.

2. Remove the three mounting

screws securing the circuit

board assembly to the

bottom of the power center.

See Figure 1.

3. Remove the mounting

hardware that secures the

power connector to the

enclosure. See Figure 1.

(*) Note: Depending on the age of the power center, the mounting hardware will

consist of either four black plastic rivets or four metal bolts/nuts.

4. Remove the four white plastic stand-offs securing the circuit board to the

mounting plate. See Figure 1.

- Continue to next page -

Mounting

Screw

Mounting

Screw

Mounting

Screw

Ground Wire

Power Connector

Mounting Hardware

Stand-offs

(4x)

Figure 1

This kit includes a control board that p ytilibapac revoc loop sedivor

.retneC rewoP 001CP GCS rolhCi eht htiw

(*) See Note in Step 3.

The instructions to install the Control Board kit are as follows:

POOL COVER KIT

Installing the New Circuit

Board

1. There are four white plastic

stand-offs pre-installed on the

new circuit board.

Line the stand-offs up with

the holes in the power center

mounting plate and press the

stand-offs into place until secured

into place. See Figure 2.

2. Secure the new power connector

to the enclosure using the four

black plastic rivets provided with

the kit. See Figure 2.

3. Connect the two RED transformer wires

to the circuit board tabs marked T1 and

T2. See Figure 3.

Note: If connectors feel loose, adjust

with needle nose pliers as needed.

4. Secure the new circuit board assembly

to the bottom of the power center with

the three mounting screws. See Figure 1

on previous page.

5. Remove the wire jumper from the green

connector plug on the top-right corner of

the circuit board. See Figure 4.

6. Insert the wires from the Pool Cover

sensor into the Green connector plug, in

Note: Please refer to your pool cover

manufacturer for additional instructions

and/or parts for your pool cover.

Note

: If the cover position sensor is not

connected after removing the jumper,

the iChlor will be forced into “Cover”

mode.

- Continue to n

ext page -

Figure 3

Figure 4

Wire Jumper

5. Slide the circuit board assembly out of the enclosure and disconnect the two RED

transformer wires.

Note: Older power centers will have a GREEN/YELLOW ground wire connecting

the circuit board to the power center’s grounding lug (see Figure 1 on previous

page). Remove and discard this wire; it will not be used with the new circuit board.

Note: Older power centers will also contain a fuse holder. Using a pair of needle-

nose pliers, unthread the fuse holder nut and remove the fuse holder assembly

from the power center. Plug the hole with the plastic cap provided in this kit.

Figure 2

Stand-Offs

Plastic

Rivets

the same location where the wire jumper

was previously installed.

Green connector

7. Plug the iChlor™ Salt Chlorine Generator (SCG) cell into the power center connector.

8. Once the pool cover is completely open the iChlor

will display a capital “C”,

symbolizing Cover mode, and will default to 5% output.

• User can adjust the desired output percentage for the “Cover Closed” while

in cover mode.

• Value will be stored as “Cover” output percentage.

• Maximum output value allowed, while the cover is closed, will be 50%.

Replace the power center cover and reestablish power.

RISK OF ELECTRIC SHOCK! Disconnect all power from the Power Center at

the circuit breaker before starting any of these procedures. Failure to do so could

result in serious injury or death to servicemen, pool users or others.

1. Open the IntellipH Controller cover and remove the

four Phillips-head screws that secure the control

panel cover.

Unplug the white, 8-position plug from the electronic

board and remove the control panel cover.

This kit contains two wire tap connectors (shown in

Figure 5). These will be used to splice both GREEN

communication wires together and both WHITE

communication wires together, following the steps

below.

Slightly open one of the tap connectors with a

ﬂat-head screwdriver, and insert one GREEN

communication wire into each of the two grooves of

the tap connector. See Figure 6.

Using a pair of , ﬁrmly press the metal tap into

the center of the connector until it is completely

inserted into the plastic connector. See Figure 7.

Close and lock the plastic connector cover over the

metal tap. See Figure 8.

7. Repeat steps 4-6 to splice the two WHITE

communication wires together.

8. IntellipH Controller is now ready to operate in stand-

alone conﬁguration, with a pool cover compatible

iChlor

PC100 power center.

Figure 5

Figure 6

Figure 7

Figure 8

Note: If the pool cover is not available at the time of installation, leave the wire

jumper shown in Figure 4 installed.

Stand-alone Installations with IntellipH

Controller and Pool

Cover Compatible PC100 Power Center

Note: The following installation instructions only apply when installing the

IntellipH Controller with the iChlor

Pool Cover kit.

1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000

10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000

WWW.PENTAIRPOOL.COM

notice..

All Pentair trademarks and logos are owned by Pentair, Inc. iChlor™ and IntellipH® are registered trademarks and/or trademarks of Pentair Water Pool

and Spa, Inc. and/or its affiliated companies in the United States and/ or other countries. Because we are continuously improving our products and services,

Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.

Pentair iChlor 523216 Installation guide

Pentair iChlor 523216 Installation guide

Pentair iChlor 523216 Installation guide

Related papers

Other documents