Important please read all instructions carefully before installing your
XHO-K15 LED ADD-ON KIT:
The complete ADD-ON KITS weight approximately 2 lbs. Reef Brite has
gone through great care to ensure that the XHO-K30 LED ADD-ON KIT
installs seamlessly to your fixture. Due to various tank sizes/glass
thicknesses and older style mounts offered, before installing it is very
important that you check your tank manufacturers specs as well as
checking the mount you are using to ensure that it is compatible and can
support the additional weight. Reef Brite will not be responsible for
improperly installed kits or any damages that may result.
If you have any questions before or during the installation of your kit, please contact
joy@reefbrite.com and one of our customer service representatives will be glad to assist
you. For faster service please provide your phone number and a good time to call. Thank
you
Installation instructions for RMS mounts:
When working near or around your aquarium make sure all working surfaces are
completely dry before handling any electrical equipment.
Make sure your fixture is unplugged from electrical outlet and
disconnected from the power supply before attempting to install the XHO-
K15 kit.
If fixture was in use even for just a short period let cool. LED’s can get very hot
during operation and can cause personal injury or damage surfaces if
proper care in handling is not taken.
Once cool, place fixture on a secure table or work surface.
Locate the four M5 x 12mm mounting screws included with your XHO-K15 kit. These
screws are required to install the XHO-K15 kit.
Do not attempt to use hardware not supplied with your XHO-K15 kit as
damage to your fixture could result.
Attach the two brackets that came with your XHO-K15 kit by placing them under the
RMS mount on your XR series light so that the holes align with RMS mount and the
threaded holes on your fixture.
Using the provided hardware attach the brackets and mount to fixture. It is
recommended to use care when threading the screws and avoid
overtightening the screws once installed.
Install the two XHO's included with the XHO-K15 kit with the screws provided on the
ends of the XHO's.
Using the supplied 2-way connector plug in each of the two XHO's.
Attach the supplied power supply in your XHO-K15 kit to 2-way connector.
When plugging in the Y connector to the XHO's or power supply to the 2-way connector,
make sure to insert plugs
until you feel them lock in place.
Make sure to locate the power supply in a safe location away from any
contact with water.
Carefully attach your fixture to the aquarium mount, plug in fixture and power supply to
a GFI outlet (Recommended) assuring a proper drip loop is employed.
Important note: Use of power strips located on floors or any location
where water can come in direct contact with them is dangerous and can
cause serious injury or fire. Make sure all electrical plugs and electrical
outlets are safely located so that water cannot splash or spill on them.
Installation instructions for hanging kits:
When working around water make sure all working surfaces are completely dry before
handling any electrical equipment.
Make sure your fixture is unplugged from electrical outlet and
disconnected from the power supply before attempting to install the XHO-
K15 kit.
If fixture was in use even for just a short period let cool. LED’s can get very hot
during operation and can cause personal injury or damage surfaces if
proper care in handling is not taken.
Once cool, place fixture on a secure table or work surface.
Locate the hardware that came with your hanging kit.
Attach the two brackets that came with your XHO-K15 kit by placing them over the top
of the fixture, so that the holes in the XHO-K15 brackets align with the threaded holes
on your fixture.
Using the supplied hardware that came with your hanging kit attach the hanging kit and
brackets to your fixture.
Do not attempt to use hardware not supplied with your hanging kit or
XHO-K15 kit as damage to your fixture could result.
Install the two XHO's included with the kit with the screws provided on the ends of the
XHO's.
Using the supplied 2-way connector plug in each of the two XHO's.
Attach the supplied power supply in your XHO-K15 kit to 2-way connector.
When plugging in the 2-way connector to the XHO's or power supply to the 2-way
connector, make sure to insert plugs until you feel them lock in place.
Make sure to locate the power supply in a safe location away from any
contact with water.
Carefully attach your fixture to the hanging cables, plug in fixture and power supply to a
GFI outlet (Recommended) assuring a proper drip loop is employed.
Important note: Use of power strips located on floors or any location
where water can come in direct contact with them is dangerous and can
cause serious injury or fire. Make sure all electrical plugs and electrical
outlets are safely located so that water cannot splash or spill on them.
IMPORTANT NOTICE:
When installing any lighting product, power supply, or controller
do not install in a manner that will allow any part or component to come
in direct contact with water.
Reef Brite assumes no liability for improperly installed products.
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
ELICA PRF0007263 Datasheet
-
State Water Heaters BTP(V)-540A User manual
-
Tanaka TBC-260SF User manual
-
Samsung CS-53007 User manual
-
Samsung CS-25V5MH User manual
-
-
Samsung CS-21H4ML User manual
-
Samsung CS-25M20MA User manual
-
Kenwood TCX752CR Owner's manual
-
Samsung CS-29M6HT User manual